Home › Engine / Hybrid System › 1BZ-FPE (ENGINE CONTROL) › ELECTRONIC CONTROLLED CARBURETOR SYSTEM › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073136 1BZ-FPE ENGINE CONTROL _0355837 ELECTRONIC CONTROLLED CARBURETOR SYSTEM C

1BZ-FPE ENGINE CONTROL  ELECTRONIC CONTROLLED CARBURETOR SYSTEM  P0110  Intake Air Temperature Circuit  


DESCRIPTION

A429919E01
1.604,1.99 1.875,1.5 1.875,1.5 2.021,1.5 true 0.052,0.458 1.042,0.698 0.99,0.24 10 false Resistance kΩ 2.115,1.396 2.906,1.635 0.792,0.24 10 false Acceptable 1.292,4.208 2.542,4.427 1.25,0.219 10 false Temperature °C (°F) 0.563,0.771 0.875,0.969 0.313,0.198 10 false 30 0.563,0.948 0.875,1.146 0.313,0.198 10 false 20 0.563,1.24 0.875,1.438 0.313,0.198 10 false 10 0.635,1.542 0.948,1.74 0.313,0.198 10 false 5 0.635,1.781 0.948,1.979 0.313,0.198 10 false 3 0.635,1.979 0.948,2.177 0.313,0.198 10 false 2 0.625,2.271 0.938,2.469 0.313,0.198 10 false 1 0.521,2.583 0.833,2.781 0.313,0.198 10 false 0.5 0.521,2.813 0.833,3.01 0.313,0.198 10 false 0.3 0.521,2.99 0.833,3.188 0.313,0.198 10 false 0.2 0.51,3.313 0.823,3.51 0.313,0.198 10 false 0.1 0.823,3.677 1.135,3.875 0.313,0.198 10 false -20 0.823,3.865 1.135,4.063 0.313,0.198 10 false (-4) 1.219,3.688 1.531,3.885 0.313,0.198 10 false 0 1.135,3.865 1.448,4.063 0.313,0.198 10 false (32) 1.521,3.688 1.833,3.885 0.313,0.198 10 false 20 1.479,3.865 1.792,4.063 0.313,0.198 10 false (68) 1.844,3.688 2.156,3.885 0.313,0.198 10 false 40 1.771,3.865 2.188,4.063 0.417,0.198 10 false (104) 2.177,3.688 2.49,3.885 0.313,0.198 10 false 60 2.115,3.865 2.594,4.083 0.479,0.219 10 false (140) 2.521,3.688 2.833,3.885 0.313,0.198 10 false 80 2.458,3.865 2.885,4.094 0.427,0.229 10 false (176) 2.792,3.688 3.135,3.885 0.344,0.198 10 false 100 2.792,3.865 3.208,4.094 0.417,0.229 10 false (212)

The intake air temp. sensor is mounted on the air cleaner cap and sensors the intake air temp.

A thermistor built in the sensor changes the resistance value according to the intake air temp. The lower the intake air temp. the greater the thermistor resistance value, and the higher the intake air temp. the lower the thermistor resistance value.

The air intake temp. sensor is connected to the engine ECU (See below). The 5V power source voltage in the engine ECU is applied to the intake air temp. sensor from the terminal THA via a resistor R.

That is the resistor R and the intake air temp. sensor are connected in series. When the resistance value of the intake air temp. sensor changes in accordance with changes in the intake air temp. the potential at terminal THA also changes. Based on this signal, the engine ECU increases the fuel injection volume to improve driveability during cold engine operation.

If the engine ECU detects the DTC "P0110", it operates the fail safe function in which the intake air temp. is assumed to be 20°C (68°F).

DTC No. DTC Detecting Condition Trouble Area
P0110/24 Open or short in intake air temp. sensor circuit for 0.5 sec. or more
·

Open or short in intake air temp. sensor circuit

·

Intake air temp. sensor

·

Engine ECU



HINT:

After confirming DTC P110 use the hand-held tester to confirm the intake air temp. from "CURRENT DATA".


Temp. Displayed Malfunction
- 40°C (- 40°F) Open circuit
140°C (284°F) or more Short circuit

WIRING DIAGRAM

A401741E01
0.5,1.833 0.958,2.031 0.458,0.198 10 false B33 0.5,2.042 2.167,2.281 1.667,0.24 10 false Intake Air Temp. Sensor 1.708,0.635 2.052,0.865 0.344,0.229 10 false THA 1.802,1.167 2.073,1.365 0.271,0.198 10 false E2 2.135,0.615 2.333,0.813 0.198,0.198 10 false 2 2.125,1.167 2.365,1.344 0.24,0.177 10 false 1 4.865,0.563 5.063,0.74 0.198,0.177 10 false 5 4.792,0.781 5.125,0.979 0.333,0.198 10 false B77 4.875,1.115 5.073,1.292 0.198,0.177 10 false 9 4.792,1.313 5.094,1.5 0.302,0.188 10 false B77 5.156,0.667 5.479,0.865 0.323,0.198 10 false THA 5.156,1.188 5.406,1.385 0.25,0.198 10 false E2 6.094,0.208 6.427,0.458 0.333,0.25 10 false 5 V 6.177,0.594 6.448,0.792 0.271,0.198 10 false R 5.844,1.896 6.167,2.104 0.323,0.208 10 false E1 5.646,2.271 6.583,2.469 0.938,0.198 10 false Engine ECU

CAUTION / NOTICE / HINT

HINT:
·

Read freed frame data using hand-held tester. Because freeze frame records the engine conditions when the malfunction is detected, when troubleshooting it is useful for determining whether the vehicle was running or stopped, the engine warmed up or not, the air-fuel ratio lean or rich, etc. at the time of the malfunction.

·

If DTC "P0105" (Vacuum Sensor Circuit Malfunction), "P0110" (Intake Air Temp. Circuit Malfunction), "P0115" (Water Temp. Circuit Malfunction), "P0120" (Throttle Position Sensor Circuit Malfunction) are output simultaneously, E2 (Sensor Ground) may be open.



PROCEDURE

1.Connect the hand-held tester, and read value of intake air temp.

PREPARATION:

a.

Connect the hand-held tester to DLC3.


b.

Turn ignition switch ON and push the hand-held tester main switch ON.


CHECK:

Read temp. value on the hand-held tester.

OK:

Same as actual intake air temp.


HINT:
·

If there is open circuit, hand-held tester indicates -40°C (- 40°F).

·

If there is short circuit, hand-held tester indicates 140°C (284°F) or more.



Result:
Result Proceed to
Same as actual intake air temp A
-40°C (-40°F) B
140°C (284°F) or more C



A

B

2.Check for open in harness or engine ECU.

C

4.Check for short in harness and engine ECU.
2.Check for open in harness or engine ECU.
A429923E02
0.802,0.271 1.125,0.469 0.323,0.198 10 false ON 0.063,1.719 1.583,1.938 1.521,0.219 10 false Intake Air Temp. Sensor 1.573,0.917 1.896,1.146 0.323,0.229 10 false 2 1.583,1.531 1.896,1.729 0.313,0.198 10 false 1 2.344,0.854 2.656,1.052 0.313,0.198 10 false 5 2.365,1.604 2.677,1.802 0.313,0.198 10 false 9 2.594,1.042 2.844,1.229 0.25,0.188 8 false THA 2.958,0.813 3.271,1.01 0.313,0.198 10 false 5V 2.625,1.26 2.938,1.458 0.313,0.198 10 false E2 2.938,1.479 3.25,1.677 0.313,0.198 10 false E1 2.271,1.073 2.583,1.271 0.313,0.198 10 false B77 2.26,1.385 2.573,1.583 0.313,0.198 10 false B77 2.552,1.781 3.354,1.99 0.802,0.208 10 false Engine ECU

PREPARATION:

a.

Disconnect the intake air temp. sensor connector.


b.

Connect sensor wire harness terminals together.


c.

Turn ignition switch ON.


CHECK:

Read temp. value on the hand-held tester.

OK:

Temp. value: 140°C (284°F) or more


Result:
Proceed to
OK
NG



OK

Confirm good good connection at sensor. If OK, replace intake air temp. sensor.

NG

3.Check for open in harness or engine ECU.
3.Check for open in harness or engine ECU.
A429924E01
1.75,3.198 1.469,2.708 true 2.083,3.302 2.26,2.729 true 0.833,0.281 1.146,0.479 0.313,0.198 10 false ON 0.052,2.042 1.573,2.26 1.521,0.219 10 false Intake Air Temp. Sensor 2.594,2.083 3.406,2.281 0.813,0.198 10 false Engine ECU 2.385,1.125 2.594,1.333 0.208,0.208 10 false 5 2.302,1.344 2.635,1.521 0.333,0.177 10 false B77 2.313,1.667 2.625,1.865 0.313,0.198 10 false B77 2.396,1.906 2.604,2.115 0.208,0.208 10 false 9 3.042,1.042 3.313,1.26 0.271,0.219 10 false 5V 2.677,1.542 2.948,1.76 0.271,0.219 10 false E2 3.01,1.76 3.281,1.979 0.271,0.219 10 false E1 2.646,1.281 2.906,1.427 0.26,0.146 8 false THA 1.333,2.542 1.74,2.729 0.406,0.188 10 false THA 2.177,2.531 2.5,2.74 0.323,0.208 10 false E2

PREPARATION:

a.

Remove the side trim bracket.


b.

Connect between terminals THA and E2 of engine ECU connector.

HINT:

Intake air temp. sensor connector is disconnected. Before checking, do a visual and contact pressure check for the engine ECU connector (Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).



c.

Turn ignition switch ON.


CHECK:

Read temp. value on the hand-held tester.

OK:

Temp. value: 140°C (284°F) or more


Result:
Proceed to
OK
NG



OK

Open in harness between terminals E2 or THA repair or replace harness.

NG

Confirm good connection at engine ECU. If OK, replace engine ECU.

4.Check for short in harness and engine ECU.
A429925E01
0.083,1.802 1.677,2.01 1.594,0.208 10 false Intake Air Temp. Sensor 0.885,0.281 1.198,0.479 0.313,0.198 10 false ON 1.271,0.927 1.469,1.135 0.198,0.208 10 false 2 1.271,1.563 1.469,1.75 0.198,0.188 10 false 1 2.313,0.875 2.521,1.073 0.208,0.198 10 false 5 2.25,1.094 2.563,1.292 0.313,0.198 10 false B77 2.333,1.625 2.552,1.833 0.219,0.208 10 false 9 2.521,1.802 3.292,2.042 0.771,0.24 10 false Engine ECU 2.948,1.5 3.188,1.667 0.24,0.167 10 false E1 2.969,0.813 3.281,1.01 0.313,0.198 10 false 5V 2.583,1.031 2.875,1.219 0.292,0.188 8 false THA 2.25,1.396 2.563,1.594 0.313,0.198 10 false B77 2.604,1.271 2.844,1.438 0.24,0.167 10 false E2

PREPARATION:

a.

Disconnect the intake air temp. sensor connector.


b.

Turn ignition switch ON.


CHECK:

Read temp. value on the hand-held tester.

OK:

Temp. value: -40°C (- 40°F)


Result:
Proceed to
OK
NG



OK

Replace intake air temp. sensor.

NG

5.Check for short in harness or engine ECU.
5.Check for short in harness or engine ECU.
A398965E01
1.927,3.74 2.188,4 true 0.604,0.281 0.917,0.479 0.313,0.198 10 false ON 0.063,1.917 1.781,2.156 1.719,0.24 10 false Intake Air Temp. Sensor 2.625,1.917 3.406,2.146 0.781,0.229 10 false Engine ECU 3.052,0.781 3.365,0.979 0.313,0.198 10 false 5 V 2.656,1.063 2.958,1.26 0.302,0.198 8 false THA 2.677,1.354 2.99,1.552 0.313,0.198 10 false E2 3.031,1.583 3.344,1.781 0.313,0.198 10 false E1 2.094,4.042 2.417,4.229 0.323,0.188 10 false B77 2.448,4.031 3.208,4.25 0.76,0.219 10 false Connector

PREPARATION:

a.

Remove the side trim bracket.


b.

Disconnect the connector of engine ECU.

HINT:

Intake air temp. sensor connector is disconnected.



c.

Turn ignition switch ON.


CHECK:

Read temp. value on the hand-held tester.

OK:

Temp. value: -40°C (- 40°F)


Result:
Proceed to
OK
NG



OK

Repair or replace harness or connector.

NG