Home › Engine / Hybrid System › 1BZ-FPE (ENGINE CONTROL) › ELECTRONIC CONTROLLED CARBURETOR SYSTEM › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073136 1BZ-FPE ENGINE CONTROL _0355837 ELECTRONIC CONTROLLED CARBURETOR SYSTEM C

1BZ-FPE ENGINE CONTROL  ELECTRONIC CONTROLLED CARBURETOR SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit  


DESCRIPTION

A398967E01
0.104,1.792 1.646,2.031 1.542,0.24 10 false Throttle Position Sensor 2.063,0.51 2.375,0.708 0.313,0.198 10 false VC 1.99,0.823 2.354,1.021 0.365,0.198 10 false VTA 2.052,1.083 2.365,1.281 0.313,0.198 10 false IDL 2.073,1.344 2.385,1.542 0.313,0.198 10 false E2 2.667,0.313 2.979,0.51 0.313,0.198 10 false 5 V 2.896,0.594 3.208,0.792 0.313,0.198 10 false +B 2.375,1.927 3.208,2.104 0.833,0.177 10 false Engine ECU

The throttle position sensor is mounted in the throttle body and detects the throttle valve opening angle.

When the throttle valve opening angle is less than 5°, the IDL contacts in the throttle position sensor are on, so the voltage at the terminal IDL of the engine ECU becomes 0 V. At this time, a voltage of approximately 0.6 V is applied to terminal VTA of the engine ECU. When the throttle valve is opened, the IDL contacts go off and thus the power source voltage of approximately 12 V in the engine ECU is applied to the terminal IDL of the engine ECU. The voltage applied to the terminal VTA of the engine ECU increases in proportion to the opening angle of the throttle valve and becomes approximately 3.2 - 4.9 V when the throttle valve is fully opened. The engine ECU judges the vehicle driving conditions from these signals input from terminals VTA and IDL, and uses them as one of the conditions for deciding the air-fuel ratio correction, power increase correction and fuel-cut control etc.

DTC No. DTC Detecting Condition Trouble Area
P0120/41 Open or short in throttle position sensor circuit for 0.5 sec. or more
·

Open or short in throttle position sensor

·

Throttle position senor

·

Engine ECU



HINT:

After confirming "DTC P0120" use the hand-held tester to confirm the throttle valve opening percentage and closed throttle position switch condition.


Throttle valve opening position expressed as percentage Trouble Area
Throttle valve fully closed Throttle valve fully open
0 % 0 % VC line open
VTA line open or short
Approx. 100 % Approx. 100 % E2 line open

WIRING DIAGRAM

A398968E01
2.698,1.167 3.01,1.365 0.313,0.198 10 false VC 2.625,2.302 3,2.51 0.375,0.208 10 false VTA 2.677,2.906 2.99,3.104 0.313,0.198 10 false IDL 2.708,3.51 3.021,3.708 0.313,0.198 10 false E2 1,4.24 1.313,4.438 0.313,0.198 10 false B31 1,4.417 2.865,4.583 1.865,0.167 10 false Throttle Position Sensor 3.042,3.5 3.354,3.698 0.313,0.198 10 false 1 3.042,2.906 3.354,3.104 0.313,0.198 10 false 2 3.042,2.302 3.354,2.5 0.313,0.198 10 false 3 3.042,1.156 3.354,1.354 0.313,0.198 10 false 4 4.917,1.104 5.229,1.302 0.313,0.198 10 false 11 4.875,1.313 5.188,1.51 0.313,0.198 10 false B77 5.208,1.292 5.521,1.49 0.313,0.198 10 false VC 4.875,2.479 5.188,2.677 0.313,0.198 10 false B77 4.885,3.063 5.198,3.26 0.313,0.198 10 false B77 4.885,3.646 5.198,3.844 0.313,0.198 10 false B77 4.917,2.271 5.229,2.469 0.313,0.198 10 false 10 5.208,2.469 5.604,2.677 0.396,0.208 10 false VTA 4.917,2.854 5.229,3.052 0.313,0.198 10 false 12 5.219,3.042 5.563,3.25 0.344,0.208 10 false IDL 4.958,3.427 5.271,3.625 0.313,0.198 10 false 9 5.208,3.635 5.521,3.833 0.313,0.198 10 false E2 5.458,4.25 6.427,4.49 0.969,0.24 10 false Engine ECU

CAUTION / NOTICE / HINT

HINT:
·

Read freed frame data using hand-held tester. Because freeze frame records the engine conditions when the malfunction is detected, when troubleshooting it is useful for determining whether the vehicle was running or stopped, the engine warmed up or not, the air-fuel ratio lean or rich, etc. at the time of the malfunction.

·

If DTC "P0105" (Vacuum Sensor Circuit Malfunction), "P0110" (Intake Air Temp. Circuit Malfunction), "P0115" (Water Temp. Circuit Malfunction), "P0120" (Throttle Position Sensor Circuit Malfunction) are output simultaneously, E2 (Sensor Ground) may be open.



PROCEDURE

1.Connect the hand-held tester and read the throttle valve opening percentage.
FI07052

PREPARATION:

a.

Connect the hand-held tester to DLC3.


b.

Turn ignition switch ON and push the hand-held tester main switch ON.


CHECK:

Read the throttle valve opening percentage.

OK:
Throttle valve Throttle valve opening position expressed as percentage
Fully open Approx. 70 %
Fully closed Approx. 10 %


Result:
Proceed to
OK
NG



OK

Check for intermittent problems.

NG

2.Check voltage between terminal 4 (VC) of wire harness side connector and body ground.
2.Check voltage between terminal 4 (VC) of wire harness side connector and body ground.
A398969E01
2,1.74 1.677,1.344 true 0.667,0.271 0.979,0.469 0.313,0.198 10 false ON 1.906,1.781 2.5,2 0.594,0.219 10 false VC (+)

PREPARATION:

a.

Disconnect the throttle position sensor connector.


b.

Turn ignition switch ON.


CHECK:

Measure voltage between terminals VC of wire harness side connector and body ground.

OK:

4.5 - 5.5 V


Result:
Proceed to
OK
NG



OK

3.Check throttle position sensor.

NG

5.Check voltage between terminals VC and E2 of engine ECU connector.
3.Check throttle position sensor.
A401585E01
0.531,1.135 1.115,0.833 true 0.552,1.854 1.094,1.354 true 0.552,1.375 1.115,1.021 true 0.552,1.615 1.135,1.167 true 0.063,0.052 0.604,0.583 0.542,0.531 10 false Throttle Position Sensor 0.427,1.042 0.625,1.24 0.198,0.198 10 false 4 0.417,1.292 0.615,1.49 0.198,0.198 10 false 3 0.417,1.542 0.615,1.74 0.198,0.198 10 false 2 0.417,1.792 0.615,1.99 0.198,0.198 10 false 1

PREPARATION:

Disconnect the throttle position sensor connector.

CHECK:

Measure resistance between terminals 1, 3 and 4 of the throttle position sensor.

OK:
Terminals Throttle valve Resistance kΩ
1 - 4 - 3.5 - 6.5
1 - 3 Fully closed 0.2 - 5.7
Fully open 2.0 - 10.2


Result:
Proceed to
OK
NG



OK

4.Check voltage between terminals VTA and E2 of engine ECU connector.

NG

Replace throttle position sensor.

4.Check voltage between terminals VTA and E2 of engine ECU connector.
A401586E01
2,1.031 1.74,0.49 true 2.083,1.042 2.323,0.469 true 0.531,0.229 0.844,0.427 0.313,0.198 10 false ON 1.594,1.833 1.906,2.031 0.313,0.198 10 false (+) 1.594,0.292 1.906,0.49 0.313,0.198 10 false VTA 2.25,0.281 2.563,0.479 0.313,0.198 10 false E2 2.333,1.833 2.646,2.031 0.313,0.198 10 false (-)

PREPARATION:

a.

Remove the side trim bracket.


b.

Turn ignition switch ON.


CHECK:

Measure voltage between terminals VTA and E2 of engine ECU connector.

OK:
Throttle valve Voltage
Fully closed 0.3 - 1.0 V
Fully open 3.2 - 4.9 V


Result:
Proceed to
OK
NG



OK

NG

Check for open and short in harness and connector between engine ECU and throttle position sensor (VTA line).

5.Check voltage between terminals VC and E2 of engine ECU connector.
A401587E01
2.073,1.042 2.281,0.479 true 1.917,1.042 1.563,0.469 true 0.542,0.188 0.854,0.385 0.313,0.198 10 false ON 1.448,0.292 1.76,0.49 0.313,0.198 10 false VC 2.198,0.292 2.51,0.49 0.313,0.198 10 false E2 1.563,1.833 1.875,2.031 0.313,0.198 10 false (+) 2.271,1.833 2.583,2.031 0.313,0.198 10 false (-)

PREPARATION:

a.

Remove the side trim bracket.


b.

Turn ignition switch ON.


CHECK:

Measure voltage between terminals VC and E2 of engine ECU connector.

OK:

Voltage 4.5 - 5.5 V


Result:
Proceed to
OK
NG



OK

Check for open in harness and connector between engine ECU and sensor (VC line).

NG