Home › Engine / Hybrid System › 1BZ-FPE (ENGINE CONTROL) › ELECTRONIC CONTROLLED CARBURETOR SYSTEM › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073136 1BZ-FPE ENGINE CONTROL _0355837 ELECTRONIC CONTROLLED CARBURETOR SYSTEM C

1BZ-FPE ENGINE CONTROL  ELECTRONIC CONTROLLED CARBURETOR SYSTEM  P0500  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The vehicle speed sensor outputs a 4 pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of these pulse signals.

G036498E02
2.385,0 3.344,0.198 0.958,0.198 10 false 4 Pulse Signal 4.083,0 5.042,0.198 0.958,0.198 10 false 4 Pulse Signal 5.135,1.354 5.51,1.552 0.375,0.198 10 false ECM 3.146,1.344 4.385,1.552 1.24,0.208 10 false Combination Meter 1.781,1.354 2.677,1.552 0.896,0.198 10 false Transmission

DTC No. DTC Detection Condition Suspected Area
P0500/42 While vehicle is being driven, no vehicle speed sensor signal to ECM
·

Open or short in speed sensor circuit

·

Vehicle speed sensor

·

Combination meter

·

ECM



WIRING DIAGRAM

A227401E03
0.667,2.573 0.979,2.781 0.313,0.208 10 false J1 0.667,2.75 2.083,3.177 1.417,0.427 10 false Combination Meter 2.073,1.531 2.313,1.708 0.24,0.177 10 false 6 5.813,2.604 6.26,2.865 0.448,0.26 10 false ECM 5.333,2.208 5.646,2.448 0.313,0.24 10 false E1 5.333,1.833 5.75,2.094 0.417,0.26 10 false SPD 5.01,2.01 5.281,2.229 0.271,0.219 10 false 24 4.969,2.198 5.354,2.417 0.385,0.219 10 false B76 5.063,1.458 5.25,1.635 0.188,0.177 10 false 9 4.969,1.656 5.292,1.958 0.323,0.302 10 false A51 1.729,1.656 2.031,1.896 0.302,0.24 10 false +S

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

OK:

Speedometer operation is normal.


HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in speedometer malfunction.




Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (SPD VOLTAGE)

NG

CHECK SPEEDOMETER CIRCUIT

2.INSPECT ECM (SPD VOLTAGE)
A227404E02
0.719,0.427 1.115,0.677 0.396,0.25 2.448,0.438 2.844,0.688 0.396,0.25 0.583,1.135 0.417,1.906 true 2.375,1.042 2.531,1.917 true 0.802,0.469 1.146,0.646 0.344,0.177 10 false B76 0.104,0.073 0.344,0.25 0.24,0.177 10 false *1 3.01,4.073 3.177,4.229 0.167,0.156 10 false *2 2.521,0.479 2.885,0.656 0.365,0.177 10 false A51 0.344,3.906 0.583,4.052 0.24,0.146 10 false 0 V 0.167,2.677 0.552,3.01 0.385,0.333 10 false 4.5 to 5.5 V 0.313,1.938 0.5,2.094 0.188,0.156 10 false E1 2.396,1.948 2.719,2.104 0.323,0.156 10 false SPD

a.

Move the transmission gear select lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage of the ECM connectors as the wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A51-9 (SPD) - B76-24 (E1) Ignition switch ON Voltage is generated intermittently


Text in Illustration
*1 Component with harness connected
(ECM)
*2 Wheel Turned

HINT:

The output voltage should fluctuate up and down (as shown in the illustration) when the wheel is turned slowly.



Result:
Proceed to
OK
NG



OK

REPLACE ECM

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
J1-6 (+S) - A51-9 (SPD) Always Below 1 Ω
J1-6 (+S) or A51-9 (SPD) - Body ground Always 10 kΩ or higher


d.

Reconnect the ECM connector.


e.

Reconnect the combination meter connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR