Home › Engine / Hybrid System › 1BZ-FPE (ENGINE CONTROL) › RELAY › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073136 1BZ-FPE ENGINE CONTROL _0355840 RELAY G

1BZ-FPE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT IG1 NO. 3 RELAY (IG1 NO. 3)

a.
A167865E14
1.979,0.708 1.521,0.354 false 2.656,0.719 3.063,0.344 false 2.531,1.125 3.063,1.125 false 2.531,1.625 3.073,1.625 false 1.208,0.76 1.344,1.01 0.135,0.25 10 false 5 0.208,0.771 0.375,0.979 0.167,0.208 10 false 3 1.229,1.302 1.385,1.594 0.156,0.292 10 false 2 0.198,1.302 0.385,1.521 0.188,0.219 10 false 1 1.427,0.26 1.615,0.479 0.188,0.219 10 false 1 3.115,0.219 3.271,0.51 0.156,0.292 10 false 2 3.115,1.552 3.281,1.76 0.167,0.208 10 false 3 3.115,1.042 3.25,1.292 0.135,0.25 10 false 5

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the IG1 NO. 3 relay.



Hide 2.INSPECT IG1 NO. 4 RELAY

a.
A167865E01
1.207,0.665 1.342,0.919 0.135,0.253 10 5 0.205,0.67 0.371,0.882 0.166,0.211 10 3 1.227,1.194 1.383,1.481 0.156,0.288 10 2 0.199,1.202 0.384,1.419 0.185,0.217 10 1 1.435,0.147 1.621,0.364 0.185,0.217 10 1 3.122,0.139 3.278,0.427 0.156,0.288 10 2 3.122,1.437 3.288,1.648 0.166,0.211 10 3 3.122,0.93 3.257,1.183 0.135,0.253 10 5 2.008,0.589 1.556,0.242 false 2.674,0.601 3.083,0.226 false 2.541,1.014 3.071,1.014 false 2.538,1.516 3.083,1.516 false

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the IG1 NO. 4 relay.



Hide 3.INSPECT ENG MAIN/LPG RELAY (ENG MAIN/LPG)

a.
A167865E01
1.207,0.665 1.342,0.919 0.135,0.253 10 5 0.205,0.67 0.371,0.882 0.166,0.211 10 3 1.227,1.194 1.383,1.481 0.156,0.288 10 2 0.199,1.202 0.384,1.419 0.185,0.217 10 1 1.435,0.147 1.621,0.364 0.185,0.217 10 1 3.122,0.139 3.278,0.427 0.156,0.288 10 2 3.122,1.437 3.288,1.648 0.166,0.211 10 3 3.122,0.93 3.257,1.183 0.135,0.253 10 5 2.008,0.589 1.556,0.242 false 2.674,0.601 3.083,0.226 false 2.541,1.014 3.071,1.014 false 2.538,1.516 3.083,1.516 false

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the ENGMAIN/LPG relay.



Hide 4.INSPECT ENG STOP RELAY (ENG STOP)

a.
E235262

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage not applied Below 1 Ω
3 - 4 Battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage not applied 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the ENG STOP relay.



Hide 5.INSPECT NO. 2 INTEGRATION RELAY

NOTICE:
·

The EDU relay, IG2 relay, EFI relay and A/F HTR relay is built into the No. 2 integration relay.

·

Before performing the relay inspection for the relay of the No. 2 integration relay, inspect the EDU fuse, IG2 NO. 1 fuse, EFI-MAIN fuse and A/F HTR fuse.



a.
A398651E01
0.76,1.479 1.052,1.646 0.292,0.167 1.896,1.479 2.188,1.646 0.292,0.167 2.719,1.479 3.01,1.646 0.292,0.167 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.833,1.49 1.146,1.688 0.313,0.198 10 false 2C 1.969,1.49 2.281,1.688 0.313,0.198 10 false 2D 2.781,1.49 3.094,1.688 0.313,0.198 10 false 2E

Inspect the EDU relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - 2C-4 Battery voltage not applied to terminals 2C-2 and 2C-3 10 kΩ or higher
Battery voltage applied to terminals 2C-2 and 2C-3 Below 1 Ω


Text in Illustration
*a Component without harness connected (No. 2 Integration Relay)

If the result is not as specified, replace the No.2 integration relay.



b.
A398651E01
0.76,1.479 1.052,1.646 0.292,0.167 1.896,1.479 2.188,1.646 0.292,0.167 2.719,1.479 3.01,1.646 0.292,0.167 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.833,1.49 1.146,1.688 0.313,0.198 10 false 2C 1.969,1.49 2.281,1.688 0.313,0.198 10 false 2D 2.781,1.49 3.094,1.688 0.313,0.198 10 false 2E

Inspect the IG2 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - 2C-8 Battery voltage not applied to terminals 2C-6 and 2C-7 10 kΩ or higher
Battery voltage applied to terminals 2C-6 and 2C-7 Below 1 Ω


Text in Illustration
*a Component without harness connected (No. 2 Integration Relay)

If the result is not as specified, replace the No.2 integration relay.



c.
A398651E01
0.76,1.479 1.052,1.646 0.292,0.167 1.896,1.479 2.188,1.646 0.292,0.167 2.719,1.479 3.01,1.646 0.292,0.167 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.833,1.49 1.146,1.688 0.313,0.198 10 false 2C 1.969,1.49 2.281,1.688 0.313,0.198 10 false 2D 2.781,1.49 3.094,1.688 0.313,0.198 10 false 2E

Inspect the EFI relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - 2D-4 Battery voltage not applied to terminals 2D-2 and 2D-3 10 kΩ or higher
Battery voltage applied to terminals 2D-2 and 2D-3 Below 1 Ω


Text in Illustration
*a Component without harness connected (No. 2 Integration Relay)

If the result is not as specified, replace the No.2 integration relay.



d.
A398651E01
0.76,1.479 1.052,1.646 0.292,0.167 1.896,1.479 2.188,1.646 0.292,0.167 2.719,1.479 3.01,1.646 0.292,0.167 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.833,1.49 1.146,1.688 0.313,0.198 10 false 2C 1.969,1.49 2.281,1.688 0.313,0.198 10 false 2D 2.781,1.49 3.094,1.688 0.313,0.198 10 false 2E

Inspect the A/F HTR relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - 2D-8 Battery voltage not applied to terminals 2D-6 and 2D-7 10 kΩ or higher
Battery voltage applied to terminals 2D-2 and 2D-3 Below 1 Ω


Text in Illustration
*a Component without harness connected (No. 2 Integration Relay)

If the result is not as specified, replace the No.2 integration relay.