Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition".
Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A52-2 (BATT) - B60-7 (E1) | GR - BR | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| A54-16 (IGSW) - B60-7 (E1) | B - BR | Ignition switch | Ignition switch ON | 11 to 14 V |
| A54-1 (+B) - B60-7 (E1) | B - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A54-13 (MREL) - B60-7 (E1) | W - BR | EFI relay | Ignition switch ON | 11 to 14 V |
| 5 seconds after ignition switch off | 0 to 2 V | |||
| B59-18 (VC) - B59-28 (E2) | L - R | Power source of sensor (a specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| A54-22 (VPA) - A54-28 (EPA) | G - LG | Accelerator pedal position sensor (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.6 to 1.0 V |
| Ignition switch ON, accelerator pedal fully depressed | 2.8 to 3.6 V | |||
| A54-23 (VPA2) - A54-29 (EPA2) | GR - G | Accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 1.4 to 1.8 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.6 to 4.4 V | |||
| A54-20 (VCPA) - A54-28 (EPA) | B*3 - LG
L*4 - LG |
Power source of accelerator pedal position sensor | Ignition switch ON | 4.5 to 5.5 V |
| B60-24 (VG) - B60-32 (EVG) | G - L | Mass air flow meter sub-assembly | Engine is warmed up: Idling | 1.5 to 1.9 V |
| B59-31 (THA) - B59-28 (E2) | V - R | Intake air temperature sensor
(built into mass air flow meter sub-assembly) |
Engine is warmed up: Idling, IAT at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| B59-20 (THIA) - B59-28 (E2) | Y - R | Intake air temperature sensor (after turbocharged) | Engine is warmed up: Idling, IAT at 0 to 80°C (32 to 176°F) | 1.0 to 4.4 V |
| B59-19 (THW) - B59-28 (E2) | G - R | Engine coolant temperature sensor | Idling, ECT at 80 to 120°C (176 to 248°F) | 0.2 to 1.0 V |
| B59-24 (#1) - B60-7 (E1)
B59-23 (#2) - B60-7 (E1) B59-22 (#3) - B60-7 (E1) B59-21 (#4) - B60-7 (E1) |
P - BR
LG - BR LG - BR GR - BR |
Injector assembly | Injector assembly Idling with warm engine | Pulse generation (See waveform 1) |
| B60-23 (G+) - B60-31 (G-) | R - G | Camshaft position sensor | Idling with warm engine | Pulse generation (See waveform 2) |
| B59-27 (NE+) - B59-34 (NE-) | B - W | Crankshaft position sensor | Idling with warm engine | Pulse generation (See waveform 2) |
| A54-18 (STP) - B60-7 (E1) | P - BR | Stop light switch assembly | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | 0 to 2 V | |||
| A54-8 (ST1-) - B60-7 (E1) | V - BR | Stop light switch assembly (opposite to STP) | Ignition switch ON, brake pedal depressed | 0 to 2 V |
| Ignition switch ON, brake pedal released | 11 to 14 V | |||
| A54-17 (TC) - B60-7 (E1) | P - BR | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| B60-18 (STA) - B60-7 (E1) | B - BR | Starter signal | Cranking | 6 V or more |
| A54-6 (TAC) - B60-7 (E1) | B - BR | Engine speed | Idling | Pulse generation (See waveform 3) |
| A54-9 (W) - B60-7 (E1) | L - BR | MIL | MIL illuminated | 0 to 2 V |
| MIL not illuminated | 11 to 14 V | |||
| A54-19 (SPD) - B60-7 (E1) | V*3 - BR
Y*4 - BR |
Speed signal from combination meter | Ignition switch ON, driving wheel slowly rotated | Pulse generation (See waveform 4) |
| B60-28 (PIM) - B59-28 (E2) | P - R | Manifold absolute pressure sensor | Applied negative pressure of 93 kPa [abs] (697 mmHg, 27.5 in.Hg) | 0.2 to 0.5 V |
| Applied positive pressure of 150 kPa [abs] (1125 mmHg, 44.3 in.Hg) | 1.0 to 1.4 V | |||
| A54-14 (IREL) - B60-7 (E1) | R - BR | EDU relay | Ignition switch ON or Idling | 0 to 2 V |
| B59-26 (PCR1) - B59-28 (E2) | L - R | Fuel pressure sensor (built into common rail assembly) | Idling (Approximately 30 MPa (306 kgf/cm2, 4351 psi)) | 1.3 to 1.7 V |
| B59-29 (THF) - B59-28 (E2) | Y - R | Fuel temperature sensor (built into injection or supply pump assembly) | Ignition switch ON | 1.2 to 1.6 V |
| B60-22 (VCG) - B60-31 (G-) | L - G | Power source of camshaft position sensor | Ignition switch ON | 4.5 to 5.5 V |
| B59-2 (PCV+) - B59-1 (PCV-) | L - L | Suction control valve (built into injection or supply pump assembly) | Idling | Pulse generation (See waveform 5) |
| B60-33 (EGLS) - B59-28 (E2) | V - R | EGR position sensor (built into EGR valve assembly) | Ignition switch ON | 3.8 to 4.2 V |
| Idling with warm engine | 3.0 to 3.5 V | |||
| B60-3 (EGRS) - B60-7 (E1) | G - BR | EGR valve assembly | Ignition switch ON | 0 to 2 V |
| Engine is warmed up, engine speed 1500 rpm | Pulse generation (See waveform 6) | |||
| B59-25 (INJF) - B60-7 (E1) | B - BR | Injector driver assembly | Idling with warm engine | Pulse generation (See waveform 7) |
| B60-20 (VLU) - B59-28 (E2) | W - R | Throttle position sensor (built into diesel throttle body assembly) | Ignition switch ON, throttle valve fully closed | 0.5 to 1.5 V |
| Ignition switch ON, throttle valve fully opened | 3.2 to 4.2 V | |||
| B60-4 (LUSL) - B60-7 (E1) | W - BR | Throttle actuator (built into diesel throttle body assembly) duty signal | Accelerator pedal released → Accelerator pedal depressed (when throttle motor is operating) | Pulse generation (See waveform 8) |
| B60-1 (THCO) - B59-28 (E2) | W - R | Exhaust gas temperature sensor (down stream) | Idling with warm engine | 4.5 to 4.9 V |
| B60-2 (THCI) - B59-28 (E2) | R - R | Exhaust gas temperature sensor (up stream) | Idling with warm engine | 4.5 to 4.9 V |
| B60-27 (PEX) - B59-28 (E2) | P - R | Differential pressure sensor | Idling with warm engine | 0.5 to 1.0 V |
| A52-15 (RGSW) - B60-7 (E1) | R - BR | DPF switch signal | DPF switch on | 11 to 14 V |
| DPF switch off | 0 to 2 V | |||
| B60-8 (EXB) - B60-7 (E1) | GR - BR | Exhaust brake | Exhaust brake operating | 11 to 14 V |
| A54-10 (W2) - B60-7 (E1) | R - BR | DPF indicator | DPF indicator on (Ignition switch ON) | 0 to 2 V |
| DPF indicator off (idling) | 11 to 14 V | |||
| B60-16 (PMB) - B60-7 (E1) | G - BR | DPF warning buzzer | Buzzer off | 11 to 14 V |
| Buzzer on | Alternating 0 to 2 Vand 11 to 14 V at intervals of 0.5seconds | |||
| A52-16 (NUSW) - B60-7 (E1)*1 | GR - BR | Exhaust brake neutral switch assembly | Ignition switch ON, shift position is neutral | 11 to 14 V |
| Ignition switch ON, shift position is not neutral | 0 to 2 V | |||
| A52-9 (CLSW) - B60-7 (E1)*2 | G - BR | Exhaust brake clutch switch (exhaust retarder switch assembly) | Clutch pedal depressed | 0 to 2 V |
| A52-13 (EXSW) - B60-7 (E1) | GR*3 - BR
P*4 - BR |
Combination switch | Exhaust brake switch on | 11 to 14 V |
| Exhaust brake switch off | 0 to 2 V | |||
| B60-12 (RSW) - B60-7 (E1)*1 | R - BR | Back-up light switch | Back-up light switch off | 0 to 2 V |
| Back-up light switch on | 11 to 14 V | |||
| A52-10 (NSW) - B60-7 (E1)*2 | B - BR | Park/neutral position switch | Ignition switch ON, shift lever position not in P or N | 11 to 14 V |
| Ignition switch ON, shift lever position in P or N | 0 to 2 V | |||
| A52-17 (CANH) - B60-7 (E1) | B - BR | CAN communication line | Engine stop and Ignition switch ON | Pulse generation (See waveform 9) |
| A52-28 (CANL) - B60-7 (E1) | W - BR | CAN communication line | Engine stop and Ignition switch ON | Pulse generation (See waveform 10) |
| A54-31 (EFI+) - B60-7 (E1)*2 | P - BR | Communication line (between ECM and TCM) | Idling | Pulse generation (See waveform 11) |
| A54-30 (EFI-) - B60-7 (E1)*2 | GR - BR | Communication line (between ECM and TCM) | Idling | Pulse generation (See waveform 12) |
| A54-25 (ECT+) - B60-7 (E1)*2 | R - BR | Communication line (between ECM and TCM) | Idling | Pulse generation (See waveform 11) |
| A54-24 (ECT-) - B60-7 (E1)*2 | G - BR | Communication line (between ECM and TCM) | Idling | Pulse generation (See waveform 12) |
| B60-7 (E1) - Body ground | BR - - | Ground | Always | Below 1 Ω |
| B59-28 (E2) - Body ground | R - - | Ground | Always | Below 1 Ω |
| B59-7 (E01) - Body ground | BR - - | Ground | Always | Below 1 Ω |
| B59-6 (E02) - Body ground | BR - - | Ground | Always | Below 1 Ω |
| B60-19 (EC) - Body ground | BR - - | Ground | Always | Below 1 Ω |
*1: for Manual Transmission
*2: for Automatic Transmission
*3: RHD
*4: LHD
Waveform 1
Injector assembly No. 1 injection signal (A)
Injector assembly No. 3 injection signal (B)
Injector assembly No. 4 injection signal (C)
Injector assembly No. 2 injection signal (D)
| Terminal No. (Symbol) | (A) B59-24 (#1) - B60-7 (E1)
(B) B59-22 (#3) - B60-7 (E1) (C) B59-21 (#4) - B60-7 (E1) (D) B59-23 (#2) - B60-7 (E1) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the injector injection.
Waveform 2
Crankshaft position sensor signal (A)
Camshaft position sensor signal (B)
| Terminal No. (Symbol) | (A) B59-27 (NE+) - B59-34 (NE-)
(B) B60-23 (G+) - B60-31 (G-) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the engine speed.
Waveform 3
Engine speed signal
| Terminal No. (Symbol) | A54-6 (TAC) - B60-7 (E1) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
Waveform 4
Vehicle speed signal
| Terminal No. (Symbol) | A54-19 (SPD) - B60-7 (E1) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Ignition switch ON, driving wheel slowly rotated |
The wavelength becomes shorter as the vehicle speed increases.
Waveform 5
Suction control valve signal
| Terminal No. (Symbol) | B59-2 (PCV+) - B59-1 (PCV-) |
| Tool Setting | 10 V/DIV., 5 msec./DIV. |
| Condition | Idling |
The waveform varies depending on the suction control valve operation.
Waveform 6
EGR position sensor signal
| Terminal No. (Symbol) | B60-3 (EGRS) - B60-7 (E1) |
| Tool Setting | 5 V/DIV., 5 msec./DIV. |
| Condition | Engine is warmed up, engine speed 1500 rpm |
Waveform 7
Injector injection confirmation signal
| Terminal No. (Symbol) | B59-25 (INJF) - B60-7 (E1) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the injector injection.
Waveform 8
Throttle actuator signal
| Terminal No. (Symbol) | B60-4 (LUSL) - B60-7 (E1) |
| Tool Setting | 1 V/DIV., 2 msec./DIV |
| Condition | Accelerator pedal released → Accelerator pedal depressed (when throttle motor is operating) |
The waveform varies depending on the throttle valve operation
Waveform 9 (Reference)
CAN communication signal
| Terminal No. (Symbol) | A52-17 (CANH) - B60-7 (E1) |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine stop and Ignition switch ON |
The waveform varies depending on the CAN communication signal.
Waveform 10 (Reference)
CAN communication signal
| Terminal No. (Symbol) | A52-28 (CANL) - B60-7 (E1) |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine stop and Ignition switch ON |
The waveform varies depending on the CAN communication signal.
Waveform 11
Communication line (between ECM and TCM)
| Terminal No. (Symbol) | A54-31 (EFI+) - B60-7 (E1)
A54-25 (ECT+) - B60-7 (E1) |
| Tester Range | 1 V/DIV., 2 msec./DIV. |
| Condition | Idling |
Waveform 12
Communication line (between ECM and TCM)
| Terminal No. (Symbol) | A54-30 (EFI-) - B60-7 (E1)
A54-24 (ECT-) - B60-7 (E1) |
| Tester Range | 1 V/DIV., 2 msec./DIV. |
| Condition | Idling |