Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM U

N04C-UH ENGINE CONTROL  ECD SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE CHART


If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.


DTC No. Detection Item Fail-safe Operation Fail-safe Deactivation Condition
P0045 Turbo / Supercharger Boost Control Solenoid Circuit / Open Limits engine power Ignition switch Off
P0087 Fuel Rail / System Pressure - Too Low
[Fuel pressure sensor system malfunction]
Limits engine power Ignition switch off to on
P0088 Fuel Rail / System Pressure - Too High
[Common rail system malfunction]
Limits engine power Ignition switch off to on
P0093 Fuel System Leak Detected - Large Leak
[Fuel leaks in common rail system]
Limits engine power for 1 minute and then stalls engine Ignition switch off to on
P0095 Intake Air Temperature Sensor 2 Circuit Intake air (intake manifold) temperature is fixed at 90°C (194°F) Normal condition is restored
P0095 Intake Air Temperature Sensor 2 Circuit Limits engine power*1 Normal condition is restored*2
P0096 Intake Air Temperature Sensor 2 Circuit Range / Performance Limits engine power*1 Normal condition is restored*2
P0097 Intake Air Temperature Sensor 2 Circuit Low Intake air (intake manifold) temperature is fixed at 90°C (194°F) Normal condition is restored
P0097 Intake Air Temperature Sensor 2 Circuit Low Limits engine power*1 Normal condition is restored*2
P0098 Intake Air Temperature Sensor 2 Circuit High Intake air (intake manifold) temperature is fixed at 90°C (194°F) Normal condition is restored
P0098 Intake Air Temperature Sensor 2 Circuit High Limits engine power*1 Normal condition is restored*2
P0100 Mass or Volume Air Flow Circuit Limits engine power*1 Normal condition is restored*2
P0101 Mass Air Flow Circuit Range / Performance Problem Limits engine power*1 Normal condition is restored*2
P0102 Mass or Volume Air Flow Meter Circuit Low Input Limits engine power*1 Normal condition is restored*2
P0103 Mass or Volume Air Flow Meter Circuit High Input Limits engine power*1 Normal condition is restored*2
P0105 Manifold Absolute Pressure / Barometric Pressure Circuit
[Intake air pressure sensor]
Manifold absolute pressure is fixed at specified value Normal condition is restored
P0105 Manifold Absolute Pressure / Barometric Pressure Circuit
[Intake air pressure sensor]
Limits engine power*1 Normal condition is restored*2
P0106 Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem Limits engine power*1 Normal condition is restored*2
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
[Intake air pressure sensor low input]
Manifold absolute pressure is fixed at specified value Normal condition is restored
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
[Intake air pressure sensor low input]
Limits engine power*1 Normal condition is restored*2
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input
[Intake air pressure sensor high input]
Manifold absolute pressure is fixed at specified value Normal condition is restored
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input
[Intake air pressure sensor high input]
Limits engine power*1 Normal condition is restored*2
P0110 Intake Air Temperature Circuit
[Intake air temperature sensor]
Intake air temperature is fixed at specified value Normal condition is restored
P0112 Intake Air Temperature Circuit Low Input
[Intake air temperature sensor low input]
Intake air temperature is fixed at specified value Normal condition is restored
P0113 Intake Air Temperature Circuit High Input
[Intake air temperature sensor high input]
Intake air temperature is fixed at specified value Normal condition is restored
P0115 Engine Coolant Temperature Circuit
[Engine coolant temperature sensor]
Engine coolant temperature sensor output is fixed at specified value (fixed value varies depending on conditions) Normal condition is restored
P0117 Engine Coolant Temperature Circuit Low Input
[Engine coolant temperature sensor low input]
Engine coolant temperature sensor output is fixed at specified value (fixed value varies depending on conditions) Normal condition is restored
P0118 Engine Coolant Temperature Circuit High Input
[Engine coolant temperature sensor high input]
Engine coolant temperature sensor output is fixed at specified value (fixed value varies depending on conditions) Normal condition is restored
P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit
[Throttle position sensor]
Limits engine power Ignition switch off
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
[Throttle position sensor low input]
Limits engine power Ignition switch off
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
[Throttle position sensor high input]
Limits engine power Ignition switch off
P0168 Fuel Temperature Too High
[Fuel temperature sensor rationality]
Limits engine power Normal condition is restored
P0180 Fuel Temperature Sensor "A" Circuit
[Fuel temperature sensor]
Fuel temperature is fixed at specified value Normal condition is restored
P0182 Fuel Temperature Sensor "A" Circuit Low Input
[Fuel temperature sensor low input]
Fuel temperature is fixed at specified value Normal condition is restored
P0183 Fuel Temperature Sensor "A" Circuit High Input
[Fuel temperature sensor high input]
Fuel temperature is fixed at specified value Normal condition is restored
P0190 Fuel Rail Pressure Sensor Circuit
[Fuel pressure sensor]
Limits engine power Normal condition is restored
P0192 Fuel Rail Pressure Sensor Circuit Low Input
[Fuel pressure sensor low input]
Limits engine power Normal condition is restored
P0193 Fuel Rail Pressure Sensor Circuit High Input
[Fuel pressure sensor high input]
Limits engine power Normal condition is restored
P0200 Injector Circuit / Open
[EDU system for injector malfunction]
When one injector circuit is malfunctioning, engine power is limited; when 2 or more ignition circuits are malfunctioning, engine is stopped Ignition switch off to on
P0234 Turbo / Supercharger Overboost Condition Limits engine power Ignition switch off
P0299 Turbocharger / Supercharger Underboost Limits engine power Ignition switch off
P0335 Crankshaft Position Sensor "A" Circuit
[Crankshaft position sensor]
Engine stopped Normal condition is restored
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low Limits engine power*1 Normal condition is restored*2
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High Limits engine power*1 Normal condition is restored*2
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance
[Intake shutter]
Limits engine power Ignition switch off
P0500 Vehicle Speed Sensor "A"
[Vehicle speed sensor]
Vehicle speed is fixed at 0 km/h (0 mph) Normal condition is restored
P0544 Exhaust Gas Temperature Sensor Circuit
(Bank1 Sensor 1)
Limits engine power Ignition switch off
P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank1 Sensor 1) Limits engine power Ignition switch off
P0546 Exhaust Gas Temperature Sensor Circuit High (Bank1 Sensor 1) Limits engine power Ignition switch off
P0627 Fuel Pump Control Circuit / Open
[Common rail system malfunction]
Engine stopped Ignition switch off to on
P1229 Fuel Pump System
[Common rail system malfunction]
Limits engine power Ignition switch off to on
P1251 Turbo/Super Charger Overboost Condition
(Too High)
Limits engine power Ignition switch off
P1425 Differential Pressure Sensor Circuit Differential pressure is fixed at specified value Ignition switch off
P1427 Differential Pressure Sensor Circuit Low Differential pressure is fixed at specified value Ignition switch off
P1428 Differential Pressure Sensor Circuit High Differential pressure is fixed at specified value Ignition switch off
P1611 RUN PULSE
[ECM]
Engine stopped Ignition switch off
P1674 Solenoid for Exhaust Brake Circuit Malfunction Exhaust brake stop operation Normal condition is restored
P2002*3 Particulate Trap Efficiency Below Threshold
(Bank 1)
Limits engine power Ignition switch off
P2031 Exhaust Gas Temperature Sensor Circuit
(Bank 1 Sensor 2)
Limits engine power Ignition switch off
P2032 Exhaust Gas Temperature Sensor Circuit Low
(Bank 1 Sensor 2)
Limits engine power Ignition switch off
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2) Limits engine power Ignition switch off
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit
[Accelerator pedal position sensor (sensor 1)]
Limits engine power Normal condition is restored
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
[Accelerator pedal position sensor rationality (sensor 1)]
Limits engine power Normal condition is restored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input
[Accelerator pedal position sensor low input (sensor 1)]
Limits engine power Normal condition is restored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input
[Accelerator pedal position sensor high input (sensor 1)]
Limits engine power Normal condition is restored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit
[Accelerator pedal position sensor (sensor 2)]
Limits engine power Normal condition is restored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input
[Accelerator pedal position sensor low input (sensor 2)]
Limits engine power Normal condition is restored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input
[Accelerator pedal position sensor high input (sensor 2)]
Limits engine power Normal condition is restored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation
[Accelerator pedal position sensor malfunction]
Limits engine power Normal condition is restored
P2226 Barometric Pressure Circuit
[ECM]
Atmospheric pressure is fixed at specified value Normal condition is restored
P2228 Barometric Pressure Circuit Low Input [ECM] Atmospheric pressure is fixed at specified value Normal condition is restored
P2229 Barometric Pressure Circuit High Input [ECM] Atmospheric pressure is fixed at specified value Normal condition is restored
P2BAB NOx Exceedance - Incorrect EGR Flow Limits engine power*1 Normal condition is restored*2
P2BAC NOx Exceedance - Deactivation of EGR Limits engine power*1 Normal condition is restored*2

A183106E09
2.615,0.458 2.802,0.458 false 2.802,0.458 3.208,1.51 false 6.063,0.385 6.219,0.385 false 6.219,0.385 6.396,1.615 false 0.313,1.927 0.75,2.167 0.438,0.24 10 false IG ON 3.833,1.896 4.271,2.135 0.438,0.24 10 false IG ON 0.24,2.406 0.75,2.646 0.51,0.24 10 false IG OFF 3.781,2.365 4.292,2.604 0.51,0.24 10 false IG OFF 0.323,2.698 1.219,3.24 0.896,0.542 10 false Malfunction is detected 0.781,1.188 1.948,1.5 1.167,0.313 10 false MIL starts blinking 1.385,1.677 3.167,1.948 1.781,0.271 10 false Total IG ON time 36 hours 0.594,0.365 2.594,0.74 2,0.375 10 false MIL remains blinking and engine output limiting control starts 1.479,2.781 3.219,3.125 1.74,0.344 10 false Idle signal is input or engine speed 200 rpm or less 3.344,2.708 4.5,3.208 1.156,0.5 10 false Vehicle returns to normal condition 4.583,2.708 5.771,3.167 1.188,0.458 10 false Normal condition is determined 4.083,1.448 5.021,1.74 0.938,0.292 10 false MIL is blinking 3.302,3.375 5.74,3.729 2.438,0.354 10 false *2: Engine output limiting control stops 0.156,3.375 3.26,3.75 3.104,0.375 10 false *1: Engine output limiting control is being enabled 4.531,0.313 6.115,0.667 1.583,0.354 10 false MIL stays on or goes off 4.417,0.865 4.646,1.104 0.229,0.24 10 false *1 6.51,0.865 6.74,1.104 0.229,0.24 10 false *2 5.813,2.74 7.115,3.271 1.302,0.531 10 false Idle signal is input or engine speed 200 rpm or less

HINT:
·

*1: The ECM will start measuring the time elapsed after the malfunction is detected at the same time the MIL starts blinking. If an idle signal is input or engine speed 200 rpm or less after the total ignition-on time has reached 36 hours have elapsed and the MIL is still blinking, engine output will be limited to 75%.

·

*2: If an idle signal is input or engine speed 200 rpm or less after the MIL stops blinking, the engine output limiting control will stop. After the ECM determines that the vehicle has returned to normal condition for 3 successive trips, the MIL will stop blinking. If the MIL is blinking, the DTC cannot be cleared using the tester.

·

*3: Fail-safe operation is not performed when a DTC is detected because of deterioration of the DPF catalyst (built into center exhaust pipe assembly).