Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › DIESEL THROTTLE BODY › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355845 DIESEL THROTTLE BODY A

N04C-UH ENGINE CONTROL  DIESEL THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 26100 1.INSTALL VENTURI ASSEMBLY

a.

Remove any seal packing material from the contact surface.


b.
A146656E03
1.813,0.896 0.802,0.188 false 0.625,0.031 0.792,0.188 0.167,0.156 10 false *a 0.896,1.896 1.156,2.052 0.26,0.156 10 false : *1

Apply a continuous bead of seal packing (width: 1.5 to 2.5 mm (0.059 to 0.098 in.)) as shown in the illustration.

Text in Illustration
*1 Seal Packing
*a 70 mm (2.75 in.)

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from contact surface.

·

Apply seal packing to the inner side of the bolt holes.

·

Install the venturi assembly within 3 minutes of applying the seal packing.

·

Do not run the engine for at least 2 hours after installing.




c.

Install the venturi assembly with the 4 nuts onto the intake pipe.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



Hide 17113 2.INSTALL INTAKE PIPE WITH VENTURI ASSEMBLY

a.

Remove any seal packing material from the contact surface.


b.
A146658E02
0.901,1.82 1.143,1.978 0.242,0.158 10 : *1

Apply a continuous bead of seal packing (width: 1.5 to 2.5 mm(0.059 to 0.098 in. )) as shown in the illustration.

Text in Illustration
*1 Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from contact surface.

·

Apply seal packing to the inner side of the bolt holes.

·

Install the venturi assembly within 3 minutes of applying the seal packing.

·

Do not run the engine for at least 2 hours after installing.




c.

Install the intake pipe with venturi assembly with the 2 nuts and 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



d.

Install the oil level dipstick guide with the bolt.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



e.

Connect the vacuum hose to the intake pipe.


f.

Connect the diesel throttle position sensor connector and the throttle control motor connector.


Hide 17342P 3.INSTALL NO. 2 AIR HOSE

a.
A226325E01
0.523,0.335 0.693,0.496 0.17,0.161 10 *a 1.062,0.949 1.232,1.109 0.17,0.161 10 *b 2.578,2.696 2.748,2.857 0.17,0.161 10 *c 2.103,3.192 2.273,3.353 0.17,0.161 10 *d 2.698,4.045 2.869,4.206 0.17,0.161 10 *e 2.784,3.842 2.784,4.024 false

Connect the No. 2 air hose and install the bolt.

Text in Illustration
*a Upper Side
*b Outside
*c Inside
*d Front Side
*e Paint Mark

Torque:

18 N*m (184 kgf*cm, 13 ft.*lbf)



b.

Tighten the hose clamp (intercooler air hose side), as shown in the illustration.


c.

Tighten the hose clamp (venturi side) until its end portion is overlapped to the paint mark.


d.

Connect the connector and the 2 hose clamps.


Hide 53712C 4.INSTALL FRONT FENDER APRON LH

a.

Install the front fender apron LH with the 6 bolts.

Torque:

7.0 N*m (71 kgf*cm, 62 in.*lbf)



Hide 51441D 5.INSTALL NO. 1 ENGINE UNDER COVER (for Plastic Type)

Hide 51441D 6.INSTALL NO. 1 ENGINE UNDER COVER (for Metal Type)

Hide 51459 7.INSTALL ENGINE SIDE COVER STAY (for TCAP Made)

Hide 58701A 8.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for LHD)

Hide 58701A 9.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for RHD)

Hide 33504F 10.INSTALL SHIFT LEVER SUB-ASSEMBLY (for Manual Transmission)

Hide 58841A 11.INSTALL SHIFTING HOLE COVER (for Automatic Transmission)

Hide 33503F 12.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for Automatic Transmission)

Hide 33820B 13.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)

Hide 33820B 14.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)

Hide 58848A 15.INSTALL SHIFT LEVER HOLE COVER WITH BOOTS (for RHD)

Hide 33531B 16.INSTALL SHIFT AND SELECT LEVER SHAFT DUST BOOT (for LHD)

Hide 58534A 17.INSTALL TRANSMISSION COVER MAT (for Manual Transmission)

Hide 58420 18.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY (for Automatic Transmission)

Hide 33820B 19.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 33820B 20.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 21. SHIFT LEVER POSITION (for Automatic Transmission)

Hide 58420 22.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58521D 23.INSTALL ENGINE SERVICE HOLE COVER MAT (w/o Carpet)

Hide 58734B 24.INSTALL ENGINE SERVICE COVER REAR WEATHERSTRIP

Hide 58410 25.INSTALL ENGINE SERVICE HOLE COVER

Hide 58521D 26.INSTALL ENGINE SERVICE HOLE COVER MAT (w/ Carpet)