Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355865 AUTOMATIC TRANSMISSION SYSTEM C

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  38  Transmission Fluid Temperature Sensor Circuit Malfunction  


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the ATF temperature into a resistance value which is input into the Transmission Control Module (TCM).

The TCM applies a voltage to the temperature sensor.

The sensor resistance changes with the ATF temperature.

One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature becomes higher.

The TCM calculates the ATF based on the voltage signal.

DTC No. DTC Detection Condition Trouble Area
38 ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1 trip detection logic)
·

Short in ATF temperature sensor circuit

·

ATF temperature sensor

·

TCM


ATF temperature sensor resistance is more than 156 kΩ for 15 minutes or more after the engine starts
DTC is detected for 0.5 sec. or more (1 trip detection logic)
·

Open in ATF temperature sensor circuit

·

ATF temperature sensor

·

TCM



MONITOR DESCRIPTION

ATF temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and the TCM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω or more than 156 kΩ, the TCM interprets this as a fault in the ATF sensor or wiring. The TCM will blinks the O/D OFF indicator light and store the DTC.

WIRING DIAGRAM

C174733E03
2.094,1.292 4.219,1.49 2.125,0.198 10 false NO.1 ATF Temperature Sensor 2.083,3.271 4.208,3.469 2.125,0.198 10 false NO.2 ATF Temperature Sensor 5.906,1.104 6.354,1.281 0.448,0.177 10 false TCM 5.625,1.646 6.073,1.823 0.448,0.177 10 false THO 5.625,2.635 6.01,2.813 0.385,0.177 10 false E2 5.625,3.625 6.052,3.802 0.427,0.177 10 false OIL2

PROCEDURE

1.INSPECT NO.1 ATF TEMPERATURE SENSOR
a.
G022837E06
1.26,1.688 1.542,1.094 true 2.115,1.698 1.865,1.094 true 2.125,1.708 2.365,1.917 0.24,0.208 10 false 1 1.177,1.708 1.417,1.917 0.24,0.208 10 false 2 0.156,0.146 0.479,0.354 0.323,0.208 10 false *1

Disconnect the NO.1 ATF temperature sensor connector from the transmission.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 79 to 156 kΩ
1 - Body ground Always 10 kΩ or higher
2 - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected:
(NO.1 ATF Temperature Sensor)

HINT:

If the resistance is not within the specified range for either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.


Standard Resistance:
ATF Temperature Specified Condition
20°C (68°F) 10.3 to 13.9 kΩ
110°C (230°F) 0.68 to 0.88 kΩ



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (NO.1 ATF TEMPERATURE SENSOR - TCM)

NG

REPLACE NO.1 ATF TEMPERATURE SENSOR

2.CHECK WIRE HARNESS (NO.1 ATF TEMPERATURE SENSOR - TCM)
a.
C174770E03
0.75,0.208 1.156,0.427 0.406,0.219 1.656,0.208 2.063,0.427 0.406,0.219 0.531,1.948 0.948,1.708 true 1.542,1.927 1.688,1.708 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *1 0.833,0.229 1.146,0.427 0.313,0.198 10 false B78 1.75,0.24 2.135,0.427 0.385,0.188 10 false A61 0.396,1.958 0.708,2.156 0.313,0.198 10 false E2 1.354,1.958 1.708,2.146 0.354,0.188 10 false THO

Disconnect the TCM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A61-15 (THO) - B78-20 (E2) Always 79 to 156 kΩ
A61-15 (THO) - Body ground Always 10 kΩ or higher
B78-20 (E2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Rear view of wire harness connector:
(to TCM)


Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (NO.2 ATF TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT TRANSMISSION WIRE (NO.2 ATF TEMPERATURE SENSOR)
a.
C174453E11
2.24,1.229 2.688,0.99 true 2.25,1.552 2.698,1.813 true 2.76,0.896 3.156,1.094 0.396,0.198 10 false OT+ 0.177,0.156 0.49,0.354 0.313,0.198 10 false *1 2.781,1.781 3.177,1.979 0.396,0.198 10 false OT-

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (OT+) - 5 (OT-) 10°C (50°F) 5.80 to 7.09Ω
1 (OT+) - 5 (OT-) 110°C (230°F) 0.231 to 0.263Ω


Text in Illustration
*1 Component without harness connected:
(Transmission Wire)


Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (NO.2 ATF TEMPERATURE SENSOR - TCM)

NG

REPLACE TRANSMISSION WIRE (NO.2 ATF TEMPERATURE SENSOR)

4.CHECK WIRE HARNESS (NO.2 ATF TEMPERATURE SENSOR - TCM)
a.
C174764E13
0.74,0.177 1.146,0.406 0.406,0.229 0.625,2.021 0.958,1.708 true 1.406,1.979 1.042,1.51 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *1 0.813,0.208 1.198,0.396 0.385,0.188 10 false B78 0.417,1.948 0.729,2.135 0.313,0.188 10 false E2 1.458,1.948 1.896,2.135 0.438,0.188 10 false OIL2

Disconnect the TCM connector.


b.

Measure the resistance of the wire harness side connector.

Standard Resistance:
Tester Connection Condition Specified Condition
B78-6 (OIL2) - B78-20 (E2) 10°C (50°F) 5.80 to 7.09Ω
B78-6 (OIL2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Rear view of wire harness connector:
(to TCM)


Result:
Proceed to
OK
NG



OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR