Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355865 AUTOMATIC TRANSMISSION SYSTEM C

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  42  Vehicle Speed Sensor Signal Circuit Malfunction  


DESCRIPTION

The vehicle speed sensor (SPD1) outputs a 4 pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the TCM. The TCM determines the vehicle speed based on the frequency of these pulse signals.

DTC No. DTC Detection Condition Trouble Area
42 All conditions below are detected 500 times or more continuously (2 trip detection logic):
(a) No signal from vehicle speed sensor (SPD1) is input to TCM if either of following condition is met:
(b) Vehicle speed is 5 km/h (3.1 mph) or more for at least 4 seconds
(c) Shift lever not on P or N
·

Open or short in vehicle speed sensor (SPD1) circuit

·

Vehicle speed sensor (SPD1)

·

Combination meter

·

TCM



WIRING DIAGRAM

C122128E27
0.646,1.104 1.99,1.302 1.344,0.198 10 false Combination Meter 5.948,0.833 6.458,1.01 0.51,0.177 10 false TCM 5.771,1.896 6.281,2.073 0.51,0.177 10 false SPD1

PROCEDURE

1.CHECK SPEEDOMETER OPERATION
a.

Check the speedometer reading in the combination meter.

HINT:

If the vehicle speed sensor has any malfunctions, the speedometer shows abnormal readings.


OK:

Speedometer operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK TCM (SPD1 SIGNAL)

NG

CHECK SPEEDOMETER CIRCUIT (INCLUDING SPEED SENSOR)

2.CHECK TCM (SPD1 SIGNAL)
a.
C174767E03
0.729,0.229 1.125,0.438 0.396,0.208 1.198,0.844 1.292,1.427 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *1 0.792,0.25 1.198,0.448 0.406,0.198 10 false B78 1.25,1.458 1.792,1.667 0.542,0.208 10 false SPD1 2.75,2.458 3.354,2.667 0.604,0.208 10 false 5 V/DIV. 2.875,3.396 3.365,3.594 0.49,0.198 10 false GND 1.677,3.885 2.677,4.083 1,0.198 10 false 20 msec./DIV.

During idling, check the waveform of the TCM connectors using an oscilloscope.


b.

Move the shift lever to N.


c.

Jack up one of the rear wheels.


d.

Measure the voltage of the TCM connectors as the wheel is turned slowly.

OK:

Refer to illustration

Item Content
Tester Connection B78-4 (SPD1) - Body ground
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Turn the rear wheel slowly


Text in Illustration
*1 Component with harness connected:
(TCM)

HINT:

When the wheel is turning slowly, voltage is output intermittently.



Result:
Proceed to
OK
NG



OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR