Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355865 AUTOMATIC TRANSMISSION SYSTEM C

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  61  Speed Sensor No. 2 Malfunction  


DESCRIPTION

The No. 2 vehicle speed sensor (SP2) detects the rotation speed of the transmission output shaft and sends signals to the TCM. The TCM determines the vehicle speed based on these signals.

AC voltage is generated in the No. 2 vehicle speed sensor (SP2) coil as the rotor mounted on the output shaft rotates, and this voltage is sent to the TCM.

The gear shift point and lock-up timing are controlled by the TCM based on the signals from the output speed sensor and throttle position sensor.

DTC No. DTC Detection Condition Trouble Area
61 All conditions below are detected 500 times or more continuously (2 trip detection logic):
1.

No signal from No. 2 vehicle speed sensor (SP2) is input to TCM while 4 pulses of No. 1 vehicle speed sensor signal are sent

2.

Vehicle speed is 5 km/h (3.1 mph) or more for at least 4 sec.

3.

Shift lever not on P or N


·

Open or short in No. 2 vehicle speed sensor (SP2) circuit

·

No. 2 vehicle speed sensor (SP2)

·

TCM



MONITOR DESCRIPTION

The output speed sensor (SP2) monitors the output shaft speed. The TCM controls the gear shift point and the lock-up timing based on the signals from the output speed sensor (SP2) and throttle position sensor.

If the TCM detects no signal from the output speed sensor (SP2) even while the vehicle is moving, the TCM will conclude that the output shaft speed sensor (SP2) is malfunctioning. The TCM will blinks the O/D OFF indicator light and set the DTC.

WIRING DIAGRAM

C119175E18
0.969,0.583 3.063,0.771 2.094,0.188 10 false NO. 2 Vehicle Speed Sensor 6.094,0.375 6.635,0.542 0.542,0.167 10 false TCM 5.865,0.958 6.406,1.125 0.542,0.167 10 false SP2+ 5.865,1.948 6.406,2.115 0.542,0.167 10 false SP2-

PROCEDURE

1.CHECK SPEED SENSOR (INSTALLATION)
a.
C159067E18
0.448,0.531 0.76,0.729 0.313,0.198 10 false *a 2.333,0.531 2.646,0.729 0.313,0.198 10 false *b 2.583,2.563 2.896,2.76 0.313,0.198 10 false *c

Check the speed sensor installation.

OK:

Installation bolt is tightened properly and there is no clearance between sensor and transmission case.


Text in Illustration
*a Correct
*b Incorrect
*c Clearance


Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 2 VEHICLE SPEED SENSOR

NG

SECURELY INSTALL SPEED SENSOR OR REPLACE SPEED SENSOR

2.INSPECT NO. 2 VEHICLE SPEED SENSOR
a.

Disconnect the no. 2 vehicle speed sensor connector from the transmission.


b.
C058536E42
1.177,1.792 1.406,1.24 true 2.25,1.813 1.969,1.26 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *1 1.115,1.813 1.385,2.01 0.271,0.198 10 false 2 2.281,1.823 2.552,2.021 0.271,0.198 10 false 1

C174768E03
0.625,0.313 1.063,0.531 0.438,0.219 1.479,1.427 1.292,0.917 true 0.75,1.49 1.292,1.104 true 0.708,0.333 1.167,0.531 0.458,0.198 10 false B78 0.188,0.104 0.49,0.302 0.302,0.198 10 false *1 0.406,1.438 0.844,1.635 0.438,0.198 10 false SP2- 1.396,1.448 1.833,1.646 0.438,0.198 10 false SP2+ 2.75,2.646 3.365,2.844 0.615,0.198 10 false 2 V/DIV. 2.844,3.365 3.333,3.552 0.49,0.188 10 false GND 1.615,4.125 2.635,4.344 1.021,0.219 10 false 20 msec./DIV.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω


Text in Illustration
*1 Component without harness connected:
(No. 2 Vehicle Speed Sensor)

HINT:

Reference: Inspect using an oscilloscope.

Check the waveform of the TCM connector.


OK:

Refer to illustration

Item Content
Tester Connection B78-3 (SP2+) - B78-16 (SP2-)
Tool Setting 2 V/DIV., 20 msec./DIV.
Condition Vehicle speed 20 km/h (12 mph)


Text in Illustration
*1 Component with harness connected:
(TCM)


Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (NO. 2 VEHICLE SPEED SENSOR - TCM)

NG

REPLACE NO. 2 VEHICLE SPEED SENSOR

3.CHECK WIRE HARNESS (NO. 2 VEHICLE SPEED SENSOR - TCM)
a.
C174764E14
0.677,0.229 1.104,0.438 0.427,0.208 1.292,1.531 1.583,1.938 true 1.292,1.688 0.698,1.969 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *1 0.76,0.25 1.146,0.448 0.385,0.198 10 false B78 0.354,1.927 0.781,2.104 0.427,0.177 10 false SP2- 1.604,1.917 2.031,2.094 0.427,0.177 10 false SP2+

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B78-3 (SP2+) - B78-16 (SP2-) 20°C (68°F) 560 to 680 Ω
B78-3 (SP2+) - Body ground 20°C (68°F) 10 kΩ or higher
B78-16 (SP2-) - Body ground 20°C (68°F) 10 kΩ or higher


Text in Illustration
*1 Rear view of wire harness connector:
(TCM)


Result:
Proceed to
OK
NG



OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR