Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355865 AUTOMATIC TRANSMISSION SYSTEM C

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  62  S1 Solenoid Valve Electrical Malfunction  63  S2 Solenoid Valve Electrical Malfunction  


DESCRIPTION

Shifting from 1st to O/D is performed in combination with the ON and OFF operation of the shift solenoid valves S1 and S2 controlled by the TCM. If an open or short circuit occurs in either of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valve to allow the vehicle to be operated safely (fail-safe function).

Fail-safe function:

If either of the shift solenoid valve circuits develops an open or short, the TCM turns the other shift solenoid ON and OFF to shift to the gear positions shown in the table below. The TCM also turns the shift solenoid valve SL and ST OFF at the same time. If both solenoids are malfunctioning, electronic hydraulic control does not operate and must be performed manually. Manual shifting as shown in the following table must be performed.

In case of a short circuit, the TCM stops sending current to the circuit.

Position Normal Shift Solenoid Valve S1 Malfunctioning
Solenoid valve Gear Solenoid valve Gear
S1 S2 S1 S2
D ON OFF 1st X ON 3rd
ON ON 2nd X ON 3rd
OFF ON 3rd X ON 3rd
OFF OFF O/D X OFF O/D
2 ON OFF 1st X ON 3rd
ON ON 2nd X ON 3rd
OFF ON 3rd X ON 3rd
L ON OFF 1st X OFF 1st
ON ON 2nd X ON 2nd

Position Shift Solenoid Valve S2 Malfunctioning Both Solenoids Malfunctioning
Solenoid valve Gear Gear when shift selector is manually operated
S1 S2
D ON X 1st O/D
OFF X O/D O/D
OFF X O/D O/D
OFF X O/D O/D
2 ON X 1st 3rd
OFF X 3rd 3rd
OFF X 3rd 3rd
L ON X 1st 1st
ON X 1st 1st

HINT:

X: Malfunction


DTC No. DTC Detection Condition Trouble Area
62 TCM detects open or short in solenoid valve S1 circuit 8 times when solenoid valve S1 is operated (1 trip detection logic)
·

Open or short in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

Transmission wire

·

TCM


63 TCM detects open or short in solenoid valve S2 circuit 8 times when solenoid valve S2 is operated (1 trip detection logic)
·

Open or short in shift solenoid valve S2 circuit

·

Shift solenoid valve S2

·

Transmission wire

·

TCM



MONITOR DESCRIPTION

The TCM controls gear shift by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, blinks the O/D OFF indicator light and stores the DTC.

The TCM performs the fail-safe function and turns the normally functioning shift solenoid valve ON/OFF.

In case of an open or short circuit, the TCM stops sending current to the circuit.

WIRING DIAGRAM

C119176E08
2.271,1.771 2.521,1.938 0.25,0.167 10 false 4 1.76,2.01 2.281,2.198 0.521,0.188 10 false SOL1 1.74,2.75 2.26,2.938 0.521,0.188 10 false SOL2 2.271,2.479 2.521,2.646 0.25,0.167 10 false 8 0.229,3.021 0.625,3.198 0.396,0.177 10 false B19 0.229,3.219 2.417,3.594 2.188,0.375 10 false Transmission Wire (Electronically Controlled Transmission Solenoid) 5.313,1.792 5.563,1.958 0.25,0.167 10 false 13 5.333,2.5 5.583,2.667 0.25,0.167 10 false 12 5.667,1.917 5.958,2.083 0.292,0.167 10 false S1 5.667,2.635 5.958,2.802 0.292,0.167 10 false S2 5.938,3.375 6.344,3.542 0.406,0.167 10 false B78 5.917,3.563 6.375,3.729 0.458,0.167 10 false TCM

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1/S2)
a.
C174453E12
0.885,0.927 1.229,1.229 true 0.885,1.802 1.219,1.573 true 0.177,0.125 0.49,0.323 0.313,0.198 10 false *1 0.469,0.823 0.948,1.021 0.479,0.198 10 false SOL1 0.479,1.74 0.958,1.938 0.479,0.198 10 false SOL2

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SOL1) - Body ground 20°C (68°F) 11 to 15 Ω
8 (SOL2) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*1 Component without harness connected:
(Transmission Wire)


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE S1/S2 - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE S1/S2
2.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE S1/S2 - TCM)
a.
C174764E15
0.635,0.177 1.063,0.406 0.427,0.229 0.479,1.948 0.479,1.542 true 1.271,2.01 0.552,1.531 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *1 0.719,0.208 1.073,0.406 0.354,0.198 10 false B78 0.385,1.958 0.74,2.156 0.354,0.198 10 false S1 1.333,1.958 1.688,2.156 0.354,0.198 10 false S2

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B78-13 (S1) - Body ground 20°C (68°F) 11 to 15 Ω
B78-12 (S2) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*1 Rear view of wire harness connector:
(to TCM)


Result:
Proceed to
OK
NG



OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE S1/S2
a.
C213093E02
0.229,0.125 0.542,0.323 0.313,0.198 10 false *1

Remove the shift solenoid valve S1/S2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Solenoid body 20°C (68°F) 11 to 15 Ω


Text in Illustration
*1 Shift solenoid valve (S1/S2)


c.

Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.


d.

Check the operating noise of the solenoid valve.

OK:

The solenoid makes an operating sound.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE S1/S2