Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355865 AUTOMATIC TRANSMISSION SYSTEM C

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  77  Linear Solenoid for Line Pressure Control Circuit Malfunction (SLT)  


DESCRIPTION

D002290E05
0.198,0.667 1.375,1.031 1.177,0.365 10 false Line Pressure Control Pressure 0.771,1.99 2.406,2.167 1.635,0.177 10 false Current Flow to Solenoid

The throttle pressure that is applied to the primary regulator valve (which modulates the line pressure) causes the solenoid valve SLT, under electronic control, to precisely modulate and generate the line pressure according to the extent that the accelerator pedal is depressed or the output of engine power.

This controls the line pressure and provides smooth shifting characteristics.

Upon receiving a signal of the throttle valve opening angle, the TCM controls the line pressure by sending a predetermined duty ratio* to the solenoid valve, modulating the line pressure and generating throttle pressure.

BE04056E06
0.375,1.313 0.74,1.51 0.365,0.198 10 false OFF 0.438,0.604 0.75,0.802 0.313,0.198 10 false ON 1.365,1.698 1.948,1.885 0.583,0.188 10 false 1 cycle

HINT:

*: The duty ratio is the ratio of the current ON time (A) to the total of the current ON and OFF time (A + B).

Duty Ratio (%) = A / (A + B) x 100


DTC No. DTC Detection Condition Trouble Area
77 TCM detects shift solenoid valve SLT circuit malfunction (1 trip detection logic)
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

TCM



WIRING DIAGRAM

C119177E24
2.167,1.417 2.604,1.604 0.438,0.188 10 false SLT+ 5.865,1.292 6.302,1.479 0.438,0.188 10 false SLT+ 2.198,2.333 2.635,2.521 0.438,0.188 10 false SLT- 5.854,2.24 6.292,2.427 0.438,0.188 10 false SLT- 2.635,1.177 2.885,1.365 0.25,0.188 10 false 2 2.656,2.104 2.906,2.292 0.25,0.188 10 false 6 5.531,1.177 5.781,1.365 0.25,0.188 10 false 26 5.521,2.104 5.771,2.292 0.25,0.188 10 false 25 0.479,2.74 0.865,2.917 0.385,0.177 10 false B19 0.49,2.927 2.708,3.292 2.219,0.365 10 false Transmission Wire (Electronically Controlled Transmission Solenoid) 6.063,2.74 6.5,2.927 0.438,0.188 10 false B78 6.063,2.938 6.5,3.125 0.438,0.188 10 false TCM

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C174453E15
1.969,1.219 2.469,0.917 true 1.99,1.573 2.448,1.854 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *1 2.531,0.813 3,1.01 0.469,0.198 10 false SLT+ 2.5,1.813 2.969,2.01 0.469,0.198 10 false SLT-

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SLT+) - 6 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
2 (SLT+) - Body ground 20°C (68°F) 10 kΩ or higher
6 (SLT-) - Body ground 20°C (68°F) 10 kΩ or higher


Text in Illustration
*1 Component without harness connected:
(Transmission Wire)


Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (SHIFT SOLENOID VALVE SLT - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK WIRE HARNESS (SHIFT SOLENOID VALVE SLT - TCM)
a.
C174764E18
0.635,0.177 1.063,0.406 0.427,0.229 0.479,1.969 0.479,1.677 true 1.198,1.99 0.552,1.677 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *1 0.719,0.208 1.073,0.406 0.354,0.198 10 false B78 0.323,1.99 0.771,2.146 0.448,0.156 10 false SLT+ 1.24,1.99 1.708,2.156 0.469,0.167 10 false SLT-

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B78-26 (SLT+) - B78-25 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
B78-26 (SLT+) - Body ground 20°C (68°F) 10 kΩ or higher
B78-25 (SLT-) - Body ground 20°C (68°F) 10 kΩ or higher


Text in Illustration
*1 Rear view of wire harness connector:
(to TCM)


Result:
Proceed to
OK
NG



OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C204845E12
0.917,0.833 1.542,1.052 true 1,2.917 1.542,3.167 true 2.448,0.833 1.885,1.052 true 2.458,2.906 1.896,3.188 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.771,0.698 1,0.896 0.229,0.198 10 false 1 0.844,2.802 1.073,3 0.229,0.198 10 false 1 2.521,0.719 2.75,0.917 0.229,0.198 10 false 2 2.521,2.802 2.75,3 0.229,0.198 10 false 2 2.875,3.594 3.281,3.792 0.406,0.198 10 false 21W

Remove the shift solenoid valve SLT.


b.

Measure the resistance between the solenoid valve terminal and solenoid valve body.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω


Text in Illustration
*1 Component without harness connected:
(Shift Solenoid Valve SLT)


c.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.


d.
C174771E03
0.583,0.229 1.021,0.479 0.438,0.25 0.427,1.521 0.427,1.042 true 1.229,1.542 0.49,1.063 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *1 0.677,0.271 1.031,0.458 0.354,0.188 10 false B78 0.292,1.552 0.698,1.74 0.406,0.188 10 false SLT+ 1.24,1.563 1.646,1.75 0.406,0.188 10 false SLT- 2.76,2.51 3.375,2.708 0.615,0.198 10 false 5 V/DIV. 2.99,3.5 3.396,3.688 0.406,0.188 10 false GND 1.583,4.031 2.5,4.219 0.917,0.188 10 false 1 msec./DIV.

Check the operating noise of terminal 1 of the solenoid valve.

OK:

The solenoid makes operating sounds.


HINT:

Reference: Inspection using an oscilloscope.

Check the waveform of the TCM connector.


OK:

Refer to illustration

Item Content
Tester Connection B78-26 (SLT+) - B78-25 (SLT-)
Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Engine idle speed


Text in Illustration
*1 Component with harness connected:
(TCM)


Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE SLT