Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355865 AUTOMATIC TRANSMISSION SYSTEM C

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  86  Engine Speed is not Input  


DESCRIPTION

Engine speed signal is input from ECM to TCM.

DTC No. DTC Detection Condition Trouble Area
86 When all conditions below remain for 4 sec. (2 trip detection logic):
1.

Engine speed is less than 300rpm.

2.

Shift lever not on P or N.


·

Open or short in engine speed signal (NE) circuit

·

ECM

·

TCM



WIRING DIAGRAM

C401814E01
1.594,0.177 2.052,0.375 0.458,0.198 10 false ECM 1.927,1.073 2.333,1.26 0.406,0.188 10 false TAC 5.167,0.167 5.625,0.365 0.458,0.198 10 false TCM 4.969,1.083 5.323,1.281 0.354,0.198 10 false NE

PROCEDURE

1.READ DTC OUTPUT
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.


Result:
Display Proceed to
DTC is not output A
DTC is output B



A

2.CHECK TCM (NE SIGNAL)

B

GO TO DTC CHART

2.CHECK TCM (NE SIGNAL)
a.
C175163E03
0.594,0.229 1.031,0.458 0.438,0.229 2.229,0.219 2.667,0.448 0.438,0.229 1.375,1.542 1.375,0.896 true 2.823,1.563 2.625,0.885 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *1 0.677,0.26 1.042,0.448 0.365,0.188 10 false B78 2.323,0.25 2.688,0.438 0.365,0.188 10 false B79 1.281,1.583 1.646,1.771 0.365,0.188 10 false NE 2.802,1.604 3.063,1.76 0.26,0.156 10 false E 2.771,2.563 3.385,2.76 0.615,0.198 10 false 2 V/DIV. 2.927,3.552 3.333,3.75 0.406,0.198 10 false GND 1.729,4.104 2.802,4.323 1.073,0.219 10 false 20 msec./DIV.

During idling, check the waveform of the TCM connectors using an oscilloscope.

OK:

Refer to illustration

Item Content
Tester Connection B78-1 (NE) - B79-2 (E)
Tool Setting 2 V/DIV., 20 msec./DIV.
Condition Idling


Text in Illustration
*1 Component with harness connected:
(TCM)


Result:
Proceed to
OK
NG



OK

REPLACE TCM

NG

3.CHECK WIRE HARNESS (ECM - TCM)
3.CHECK WIRE HARNESS (ECM - TCM)
a.

Disconnect the ECM connector.


b.

Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester connection Condition Specified Condition
A54-6 (TAC) - B78-1 (NE) Always Below 1Ω
A54-6 (TAC) or B78-1 (NE) - Body ground Always 10kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR