Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TORQUE CONVERTER AND DRIVE PLATE › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355875 TORQUE CONVERTER AND DRIVE PLATE G

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

a.
C372971E01
0.969,0.042 2.615,1.063 1.646,1.021 10 false Sample showing maximum amount of powder in ATF 1.365,3.99 2.552,4.313 1.188,0.323 10 false Actual Size

Determine the condition of the torque converter assembly.

i.

If the inspection result of the torque converter assembly meets the following items, replace the torque converter assembly.

Malfunction item:

Any metallic sound is heard from the torque converter assembly during stall test or when the shift lever is in neutral position.

The one-way clutch is free or locked in both directions.

Fine powders exceeding the sample limit are identified in ATF. (See the sample.)


HINT:

The sample shows the auto fluid of approx. 0.25 liters (0.26 US qts, 0.22 lmp. qts) that is taken out from the removed torque converter assembly.




b.

Change the ATF in the torque converter assembly.

i.

If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter assembly and drain it with the face for installation facing up.



c.
C011090

Clean and check the oil cooler and oil pipe line.

i.

If the torque converter assembly is inspected or the ATF is changed, clean the oil cooler and oil pipe line.

HINT:
·

Spray compressed air of 196 kPa (2 kgf/ cm 2 , 28 psi) from the inlet hose.

·

If plenty of fine powders are identified in the ATF, add new ATF using a bucket pump and clean it again.




ii.

If the ATF is cloudy, inspect the oil cooler (radiator).



d.
D025368E99
1.729,1.865 2.219,1.042 false 0.49,0.177 0.896,0.417 0.406,0.24 10 false OK 1.531,0.188 2.021,0.49 0.49,0.302 10 false NG 2.281,0.948 3.135,1.5 0.854,0.552 10 false The Bottom is Damaged

Prevent deformation of the torque converter assembly.

i.

When there is any damage on the end of the bolt for the torque converter assembly and on the bottom of the bolt hole, replace the bolt and the torque converter assembly.


ii.

All of the bolts shall have the same length.


iii.

Do not lose the spring washers.



e.
C153934

Temporarily mount the torque converter assembly to the drive plate. Set up a dial indicator and measure the torque converter clutch sleeve runout.

Maximum runout:

0.30 mm (0.0118 in.)


If runout is not within specification, try to correct by changing the installation direction of the converter clutch.

HINT:

Mark the position of the converter clutch to reinstall it correctly.



f.

Remove the torque converter assembly.


Hide 32101A 2.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
C153935

Set up a dial indicator with a roller instrument and measure the drive plate runout.


b.

Check for damage of the ring gear.

Maximum runout:

0.25 mm (0.0098 in.)


If runout is not within specification or ring gear is damaged, replace the drive plate.

Torque:

190 N*m (1940 kgf*cm, 140 ft.*lbf)