Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OVERDRIVE PLANETARY GEAR, OVERDRIVE DIRECT AND OVERDRIVE DIRECT DRUM ASSEMBLY › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355881 OVERDRIVE PLANETARY GEAR, OVERDRIVE DIRECT AND OVERDRIVE DIRECT DRUM ASSEMBLY G

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  OVERDRIVE PLANETARY GEAR, OVERDRIVE DIRECT AND OVERDRIVE DIRECT DRUM ASSEMBLY  INSPECTION  


PROCEDURE

Hide 34714 1.INSPECT OVERDRIVE 1 WAY CLUTCH

a.
Q002732

Hold the overdrive direct clutch drum sub-assembly, and turn the input shaft.


b.

Check that the overdrive 1 way clutch turns freely clockwise and locks counterclockwise.

NOTICE:

If there is a problem with the overdrive 1 way clutch, replace the new one.



Hide 35633D 2.INSPECT OVERDRIVE DIRECT CLUTCH CLUTCH DISC

a.
C086967

Check whether the sliding surfaces of the 3discs, the 3 plates, and the flange are worn or burnt. If necessary, replace them.

NOTICE:

If the linings of the discs are peeled off or discolored, or if any part of the printed numbers is damaged, replace all discs.



Hide 34602 3.INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
Q000470

Check that the check ball is free by shaking the piston.


b.

Check that the valve does not have leaks by applying low-pressure compressed air.


Hide 34601 4.INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

a.
C086968

Using a dial indicator, measure the inside diameter of the overdrive direct clutch drum sub-assembly bushing.

Standard inside diameter:

26.500 to 26.521 mm (1.0433 to 1.0441 in.)


Limit inside diameter:

26.57 mm (1.0461 in.)


NOTICE:

Measure it at several positions and take the average. If the value is over the limit, replace the new direct clutch drum sub-assembly.



Hide 34710 5.INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY

a.
C086969

Using a dial indicator, measure the inside diameter of the overdrive planetary gear assembly bushing.

Standard inside diameter:

12.00 to 12.018 mm (0.4724 to 0.4731 in.)


Limit inside diameter:

12.070 mm (0.4752 in.)


NOTICE:

Measure it at several positions and take the average. If the value is over the limit, replace the new overdrive planetary gear assembly.



b.
C086970

Using a feeler gauge, measure the overdrive planetary gear pinion thrust clearance.

Standard clearance:

0.20 to 0.59 mm (0.0008 to 0.0020 in.)


Limit clearance:

0.8 mm (0.0315 in.)


NOTICE:

If the clearance is greater than the standard clearance, replace the overdrive planetary gear assembly.



Hide 6.INSPECT PISTON STROKE OF OVERDRIVE DIRECT CLUTCH

a.
Q002786

Place the oil pump body on the torque converter clutch.


b.
C086952

Install the overdrive direct clutch assembly to the front oil pump assembly.

NOTICE:

Be careful not to damage the front oil pump oil seal ring.



c.
C403422E01
0.917,0.646 1.469,0.906 false 0.604,0.542 1.125,0.771 0.521,0.229 10 false SST

Install the SST to the dial indicator, and then set them to the direct clutch piston vertically.

SST
09350-36010  (09350-06110)

NOTICE:

Do not let the SST touch except the piston.



d.

Make sure the piston moves smoothly when applying compressed air to the oil hole of the oil pump body.

Standard:

1.80 to 2.07 mm (0.0709 to 0.0815 in.)


NOTICE:

Measure it at several positions and take the average. If the value is over the limit, check the flange, and then replace the defective parts.


HINT:
Clutch flange Mark thickness
35675-60070 A 4.50 to 4.60mm (0.1772 to 0.1811 in.)
35675-60080 B 4.67 to 4.77 mm (0.1839 to 0.1878 in.)
35675-60090 C 4.84 to 4.94 mm (0.1906 to 0.1945 in.)
35675-60100 D 5.01 to 5.11 mm (0.1972 to 0.2012 in.)