Home › Drivetrain › CLUTCH › CLUTCH PEDAL(w/ Turn Over)
RM2850E _52 Drivetrain _073140 CLUTCH _0355885 CLUTCH PEDAL(w/ Turn Over) A

CLUTCH  CLUTCH PEDAL(w/ Turn Over)  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.
C371464

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31453B 2.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

a.

Install a new clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.

HINT:

Install the clutch master cylinder push rod clevis bush from the left side of the vehicle.



b.
C371479

Apply MP grease to the inside of the clutch master cylinder push rod clevis bush.

Text in Illustration
V100135

MP grease


Hide 31301B 3.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.
C371482

Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31301C 4.INSTALL CLUTCH PEDAL BUSH

a.
C377143E01
2.458,1.104 2.219,1.104 2.219,1.104 1.927,0.51 false 0.688,1.396 0.885,1.396 0.885,1.396 1.021,0.76 false 2.302,0.385 2.76,0.385 false 2.49,1.021 2.729,1.25 0.24,0.229 10 false *1 2.802,0.302 3.031,0.542 0.229,0.24 10 false *2 0.469,1.313 0.698,1.563 0.229,0.25 10 false *2

Apply MP grease to both sides of 2 new clutch pedal bushes and the clutch pedal shaft collar.

Text in Illustration
*1 Clutch Pedal Shaft Collar
*2 Clutch Pedal Bush
V100135

MP grease


b.

Install the 2 clutch pedal bushes and clutch pedal shaft collar to the clutch pedal sub-assembly.


Hide 31353 5.INSTALL CLUTCH PEDAL SPRING HOLDER

C371481E01
2.656,0.188 2.865,0.188 2.865,0.188 3.063,0.573 false 2.958,1.479 2.75,1.479 2.75,1.479 2.604,1.052 false 2.146,1.688 1.938,1.688 1.938,1.688 1.792,1.26 false 1.271,1.844 1.063,1.844 1.063,1.844 0.917,1.417 false 3,1.385 3.25,1.635 0.25,0.25 10 false *1 2.177,1.604 2.396,1.823 0.219,0.219 10 false *2 1.313,1.76 1.531,1.99 0.219,0.229 10 false *3 2.438,0.104 2.656,0.333 0.219,0.229 10 false *4

a.

Apply MP grease to the inside of the clutch pedal spring holder, inside of the clutch pedal spring, hook of the clutch pedal spring and both sides of a new clutch pedal bush.

Text in Illustration
*1 Clutch Pedal Spring Holder
*2 Clutch Pedal Spring
*3 Clutch Pedal Bush
*4 E-Ring
V100135

MP grease


b.

Install the clutch pedal spring holder, clutch pedal spring and clutch pedal bush to the clutch pedal bracket sub-assembly with a new E-ring.


Hide 31301 6.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.
C368728

Install the clutch pedal sub-assembly to the pedal bracket sub-assembly with the bolt, spring washer and nut.

Torque:

30 N*m (306 kgf*cm, 22 ft.*lbf)


NOTICE:

Turn the nut while holding the bolt.



Hide 31453A 7.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

a.
C377144E01
0.708,0.219 0.969,0.458 0.26,0.24 10 false *a 1.75,0.208 2,0.427 0.25,0.219 10 false *b

Apply MP grease to the clutch master cylinder push rod clevis with hole pin.

Text in Illustration
*a OK
*b NG
V100135

MP grease


b.

Install the clutch master cylinder push rod clevis with hole pin with a new clip as shown in the illustration.


Hide 31301P 8.INSTALL CLUTCH PEDAL TURNOVER BUSH

a.

Install a new clutch pedal turnover bush to the clutch pedal sub-assembly.


b.
C371476

Apply MP grease to the contact surface of the clutch pedal turnover bush and turn over clutch pedal spring.

Text in Illustration
V100135

MP grease


Hide 31301R 9.INSTALL TURN OVER SPRING SEAT COMPRESSION SPRING

a.
C375007

Apply MP grease to the inside of the turn over spring seat compression spring and hook of the turn over spring seat compression spring.

Text in Illustration
V100135

MP grease


b.
C368727

While the clutch pedal is fully depressed, install the turn over spring seat compression spring.


Hide 10.INSTALL CLUTCH PEDAL STOPPER BOLT

a.

w/o Exhaust Brake:

i.
C368724

Install the clutch pedal stopper bolt to the clutch pedal bracket sub-assembly and temporarily install the lock nut.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.




Hide 84640C 11.INSTALL EXHAUST RETARDER SWITCH ASSEMBLY

a.

w/ Exhaust Brake:

i.
C368725

Temporarily install the exhaust retarder switch assembly to the clutch pedal bracket sub-assembly with the lock nut.


ii.
C368719E02
1.177,1.854 1.417,2.073 0.24,0.219 10 false *a

Adjust the exhaust retarder switch assembly by turning it so that the gap between the thread of the exhaust retarder switch assembly and No. 1 clutch pedal cushion reaches the standard clearance when the clutch pedal is released slowly.

Standard Clearance:

0 to 0.5 mm (0 to 0.0196 in.)


Text in Illustration
*a 0 to 0.5 mm (0 to 0.0196 in.)

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



iii.
C371475

Connect the connector and attach the clamp.



Hide 12.INSPECT AND ADJUST CLUTCH PEDAL