11101
1.INSPECT CYLINDER HEAD SUB-ASSEMBLY
Using a precision straightedge and feeler gauge, measure the warpage on the cylinder block side and the intake and exhaust manifold sides.
0.10 mm (0.00394 in.)
|
If the warpage is more than the maximum, replace the cylinder head sub-assembly. |
|
| *a | Cylinder Block Side |
| *b | Intake Manifold Side |
| *c | Exhaust Manifold Side |
Using a dye penetrant, check the cylinder head sub-assembly for cracks.
If there are cracks, replace the cylinder head sub-assembly.
2.INSPECT INNER COMPRESSION SPRING
Using a steel square, measure the deviation of the inner compression spring.
2.0 mm (0.0787 in.)
|
If the deviation is more than the maximum, replace the inner compression spring. |
|
| *a | Deviation |
Using a vernier caliper, measure the free length of the inner compression spring.
85.1 mm (3.35 in.)
82.1 mm (3.23 in.)
If the free length is less than the minimum, replace the inner compression spring.
13711
3.INSPECT INTAKE VALVE
Visually check the valves for damage, burns, carbon or warpage, and check the valve heads, valve stems and valve stem grooves for cracks.
If excessive wear, burns, warpage or cracks are present, replace the intake valves.
Check the valve seating condition.
Lightly apply Prussian blue marking compound to the valve face.
Tapping the valve against the seat, check the seating condition.
If the Prussian blue mark is not concentric or the compound is scattered all around the valve face or seat, repair the valve face or the intake valve seat.
Using a micrometer, measure the diameter of the valve stem.
6.957 to 6.972 mm (0.274 to 0.275 in.)
13715
4.INSPECT EXHAUST VALVE
Visually check the valves for damage, burns, carbon or warpage. Check the valve heads, valve stems and valve stem grooves for cracks.
If excessive wear, burns, warpage or cracks are present, replace the exhaust valves.
Check the valve seating condition.
Lightly apply Prussian blue marking compound to the valve face.
Tapping the valve against the seat, check the seating condition.
If the Prussian blue mark is not concentric or the compound is scattered all around the valve face or seat, repair the valve face or the exhaust valve seat.
Using a micrometer, measure the diameter of the valve stem.
6.932 to 6.947 mm (0.273 to 0.274 in.)
5.INSPECT VALVE GUIDE BUSH OIL CLEARANCE
Using a caliper gauge, measure the internal diameter of the valve guide bush.
7.000 to 7.015 mm (0.2756 to 0.2762 in.)
If the bore diameter is not as specified, replace the valve guide bush.
Subtract the valve stem diameter measurement from the bore diameter measurement of the valve guide bush to calculate the oil clearance.
| Item | Specified Condition |
|---|---|
| Intake | 0.028 to 0.058 mm (0.00110 to 0.00228 in.) |
| Exhaust | 0.053 to 0.083 mm (0.00209 to 0.00327 in.) |
| Item | Specified Condition |
|---|---|
|
If the oil clearance is more than the maximum, replace the valve and valve guide bush. |
|
| Intake | 0.12 mm (0.00472 in.) |
| Exhaust | 0.15 mm (0.00591 in.) |
6.INSPECT INTAKE VALVE SINK
Using a vernier caliper, measure the intake valve sink.
0.8 to 1.0 mm (0.0315 to 0.0394 in.)
1.1 mm (0.0433 in.)
If the sink is more than the maximum, replace the intake valve and intake valve seat.
If the valve heads are protruding from the cylinder head surface, the valve heads may hit the pistons when the engine is running.
When replacing the intake valve and intake valve seat, always recheck the seating condition.
7.INSPECT EXHAUST VALVE SINK
Using a vernier caliper, measure the exhaust valve sink.
1.8 to 2.0 mm (0.0709 to 0.0787 in.)
2.1 mm (0.0827 in.)
If the sink is more than the maximum, replace the valve and exhaust valve seat.
If the valve heads are protruding from the cylinder head surface, the valve heads may hit the pistons when the engine is running.
When replacing the exhaust valve and exhaust valve seat, always recheck the seating condition.