Home › Engine / Hybrid System › N04C-VQ (LUBRICATION) › OIL PUMP
RM2850E _51 Engine / Hybrid System _073148 N04C-VQ LUBRICATION _0355937 OIL PUMP G

N04C-VQ LUBRICATION  OIL PUMP  INSPECTION  


PROCEDURE

Hide 15100 1.INSPECT OIL PUMP ASSEMBLY

a.

Visually check each part of the oil pump assembly for damage or wear.

If damage or wear is excessive, replace the oil pump assembly with a new one.


b.
A157026

Inspect the clearance between the oil pump drive gear and cylinder block.

i.

Using a vernier caliper, measure the length of the oil pump drive gear.

Standard:

27.02 to 27.04 mm (1.0638 to 1.0646 in.)



ii.
A157027

Using a vernier caliper, measure the depth of the cylinder block.

Standard:

27.027 to 27.067 mm (1.0641 to 1.0656 in.)



iii.

Add the measurement of the cylinder block to the thickness of the gasket. From this total, subtract the measurement of the oil pump drive gear.

Standard clearance:

0.047 to 0.147 mm (0.0019 to 0.0058 in.)


Maximum clearance:

0.17 mm (0.0067 in.)


If the clearance is greater than the maximum, replace the oil pump assembly or cylinder block.



c.
A157028

Inspect the backlash between the oil pump drive gear and oil pump driven gear.

i.

Using a vise, fix the oil pump assembly.


ii.

Using a dial indicator, measure the backlash between the oil pump drive gear and oil pump driven gear.

Standard backlash:

0.137 to 0.302 mm (0.0054 to 0.0119 in.)


Maximum backlash:

0.302 mm (0.0119 in.)


If the backlash is greater than the maximum, replace the oil pump assembly with a new one.



d.
A157029

Inspect the clearance between the oil pump drive gear shaft and oil pump drive gear bush.

i.

Using a micrometer, measure the diameter of the oil pump drive gear shaft.

Standard shaft diameter:

18.088 to 18.106 mm (0.7121 to 0.7128 in.)



ii.
A157030

Using a dial indicator, measure the inside diameter of the oil pump drive gear bush.

Standard bush inside diameter:

18.146 to 18.187 mm (0.7144 to 0.7160 in.)



iii.

Subtract the diameter measurement of the oil pump drive gear shaft from the inside diameter measurement of the oil pump drive gear bush.

Standard clearance:

0.040 to 0.099 mm (0.0016 to 0.0039 in.)


Maximum clearance:

0.13 mm (0.0051 in.)


If the clearance is greater than the maximum, replace the oil pump assembly or drive gear bush.



e.
A157031

Inspect the clearance between the oil pump driven gear shaft and oil pump driven gear bush.

i.

Using a micrometer, measure the diameter of the oil pump driven gear shaft.

Standard shaft diameter:

17.979 to 17.997 mm (0.7078 to 0.7085 in.)



ii.
A157032

Using a dial indicator, measure the inside diameter of the oil pump driven gear bush.

Standard bush inside diameter:

18.037 to 18.054 mm (0.7101 to 0.7108 in.)



iii.

Subtract the diameter measurement of the oil pump driven gear shaft from the inside diameter measurement of the oil pump driven gear bush.

Standard clearance:

0.040 to 0.075 mm (0.0016 to 0.0030 in.)


Maximum clearance:

0.13 mm (0.0051 in.)


If the clearance is greater than the maximum, replace the oil pump driven gear or oil pump assembly.



f.
A147521E05
2.406,0.719 2.25,0.167 2.25,0.167 2.167,0.167 false 0.729,1.146 0.417,0.917 false 1.594,1.396 1.583,1.896 false 2.031,0.104 2.208,0.302 0.177,0.198 10 true *1 0.25,0.802 0.427,0.948 0.177,0.146 10 false *a 1.521,1.938 1.708,2.135 0.188,0.198 10 true *2

Using a dial indicator, measure the backlash between the oil pump gear and No. 1 idle gear sub-assembly.

Text in Illustration
*1 No. 1 Idle Gear Sub-assembly
*2 Oil Pump Gear
*a Dial Indicator

Standard backlash:

0.065 to 0.181 mm (0.0026 to 0.0071 in.)


Maximum backlash:

0.3 mm (0.0118 in.)


If the backlash is greater than the maximum, replace the oil pump assembly and No. 1 idle gear sub-assembly.