Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › CYLINDER HEAD
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0356003 CYLINDER HEAD G

N04C-VL ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER HEAD FOR FLATNESS

a.

Using a precision straightedge and feeler gauge, measure the warpage on the cylinder block side and the intake and exhaust manifold sides.

Maximum Warpage:

0.10 mm (0.00394 in.)


Text in Illustration
*a Cylinder Block Side
*b Intake Manifold Side
*c Exhaust Manifold Side

A318160N01
4.083,0.198 4.396,0.354 0.313,0.156 10 false *a 0.75,1.667 1.063,1.823 0.313,0.156 10 false *b 4.135,1.667 4.448,1.823 0.313,0.156 10 false *c


Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.
A146580

Using a dye penetrant, check the cylinder head for cracks.


Hide 3.INSPECT INNER COMPRESSION SPRING

a.
A137173E03
1.209,0.288 1.389,0.445 0.18,0.156 10 *a

Using a steel square and feeler gauge, measure the deviation of the compression spring.

Maximum Deviation:

2.0 mm (0.0787 in.)


Text in Illustration

If the deviation is greater than the maximum, replace the inner compression spring.

*a Deviation


b.
EM00801E01
2.964,1.994 3.414,2.145 0.45,0.151

Using a vernier caliper, measure the free length of the compression spring.

Standard Free Length:

85.1 mm (3.350 in.)

Maximum Free Length:

82.1 mm (3.232 in.)


If the free length is not as specified, replace the inner compression spring.


Hide 13711 4.INSPECT INTAKE VALVE

a.
A146585E04
1.6,1.06 1.79,1.225 0.19,0.166 10 *a

Visually check the valves for damage, burns, carbon or warpage, and check the valve heads, valve stems and valve stem grooves for cracks.

If there is excessive wear, burns, warpage or cracks, replace the valves.

Text in Illustration
*a Width


b.

Check the valve seating condition.

i.

Lightly apply Prussian Blue marking compound to the valve face.


ii.

Tapping the valve against the seat, check the seating condition.

If the Prussian Blue mark is not concentric or the compound is scattered all around the valve face or seat, correct the valve face or the valve seat.



c.
A137170

Using a micrometer, measure the diameter of the valve stem.

Valve Stem Diameter:

6.957 to 6.972 mm (0.2740 to 0.2745 in.)



Hide 13715 5.INSPECT EXHAUST VALVE

a.
A146585E04
1.6,1.06 1.79,1.225 0.19,0.166 10 *a

Visually check the valves for damage, burns, carbon or warpage, and check the valve heads, valve stems and valve stem grooves for cracks.

If there is excessive wear, burns, warpage or cracks, replace the valves.

Text in Illustration
*a Width


b.

Check the valve seating condition.

i.

Lightly apply Prussian Blue marking compound to the valve face.


ii.

Tapping the valve against the seat, check the seating condition.

If the Prussian Blue mark is not concentric or the compound is scattered all around the valve face or seat, correct the valve face or the valve seat.



c.
A137170

Using a micrometer, measure the diameter of the valve stem.

Valve Stem Diameter:

6.932 to 6.947 mm (0.2729 to 0.2735 in.)



Hide 6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A146578

Using a caliper gauge, measure the internal diameter of the valve guide bush.

Inside Diameter:

7.000 to 7.015 mm (0.2756 to 0.2762 in.)



b.

Subtract the valve stem diameter measurement from the internal diameter measurement of the valve guide bush to calculate the oil clearance.

Standard Oil Clearance:
Intake:

0.028 to 0.058 mm (0.00110 to 0.00228 in.)

Exhaust:

0.053 to 0.083 mm (0.00209 to 0.00327 in.)


Maximum Oil Clearance:
Intake:

0.12 mm (0.00472 in.)

Exhaust:

0.15 mm (0.00591 in.)


If the oil clearance is greater than the maximum, replace the valve or valve guide.


Hide 7.INSPECT INTAKE VALVE SINK

a.
A146577E01
1.725,0.553 1.882,0.726 0.157,0.173 10 *a

Using a precision straightedge and feeler gauge, measure the valve depth.

Standard Depth:

0.8 to 1.0 mm (0.0315 to 0.0394 in.)

Maximum Depth:

1.1 mm (0.0433 in.)


Text in Illustration

If the depth is greater than the maximum, replace the valve and valve seat.

*a Depth

NOTICE:
·

If the valve heads are protruding from the cylinder head surface, the valve heads may hit against the pistons while the engine is running.

·

When replacing the valve and valve seat, always recheck the seating condition.




Hide 8.INSPECT EXHAUST VALVE SINK

a.
A146577E01
1.725,0.553 1.882,0.726 0.157,0.173 10 *a

Using a precision straightedge and feeler gauge, measure the valve depth.

Standard Depth:

1.8 to 2.0 mm (0.0709 to 0.0787 in.)

Maximum Depth:

2.1 mm (0.0827 in.)


Text in Illustration

If the depth is greater than the maximum, replace the valve and valve seat.

*a Depth

NOTICE:
·

If the valve heads are protruding from the cylinder head surface, the valve heads may hit against the pistons while the engine is running.

·

When replacing the valve and valve seat, always recheck the seating condition.