Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › CYLINDER HEAD
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0356003 CYLINDER HEAD A

N04C-VL ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11131 1.REMOVE INTAKE VALVE SEAT

a.
A146573E09
1.646,0.958 1.167,0.49 false 2.031,1.708 2.365,0.656 false 1.875,1.771 2.542,1.698 2.542,1.698 1.948,2.406 false 1.865,2.615 2.26,2.615 false 1.406,1.938 0.813,2.563 0.813,2.563 1.479,2.458 false 0.99,0.365 1.167,0.531 0.177,0.167 10 false *1 2.365,0.5 2.563,0.688 0.198,0.188 10 false *2 2.583,1.583 2.771,1.76 0.188,0.177 10 false *3 0.604,2.5 0.76,2.677 0.156,0.177 10 false *a 2.302,2.531 2.479,2.698 0.177,0.167 10 false *b

Grind the 3 places on the circumference of a used valve and weld it to the valve seat as shown in the illustration.

Text in Illustration
*1 Brass Block
*2 Valve Seat
*3 Valve
*a Electric Welding Applied
*b Grind these Points with Grinder

NOTICE:

To protect the lower surface of the cylinder head from welding spatters, be sure to apply grease before welding.



b.

Place a brass block on the top of the valve stem and strike it with a hammer to remove the valve seat.

CAUTION:

When striking, the valve tips may break off on impact. Wear safety glasses to protect your eyes.



Hide 11135 2.REMOVE EXHAUST VALVE SEAT

a.
A146573E10
1.646,0.969 1.167,0.5 false 2.021,1.708 2.354,0.656 false 1.875,1.771 2.542,1.698 2.542,1.698 1.927,2.406 false 1.833,2.604 2.281,2.563 false 1.406,1.938 0.813,2.563 0.813,2.563 1.479,2.458 false 0.99,0.365 1.167,0.531 0.177,0.167 10 false *1 2.365,0.51 2.563,0.698 0.198,0.188 10 false *2 2.583,1.583 2.771,1.76 0.188,0.177 10 false *3 0.604,2.5 0.76,2.677 0.156,0.177 10 false *a 2.333,2.469 2.51,2.635 0.177,0.167 10 false *b

Grind 3 places on the circumference of a used valve and weld it to the valve seat as shown in the illustration.

Text in Illustration
*1 Brass Block
*2 Valve Seat
*3 Valve
*a Electric Welding Applied
*b Grind these Points with Grinder

NOTICE:

To protect the lower surface of the cylinder head from welding spatters, be sure to apply grease before welding.



b.

Place a brass block on the top of the valve stem and strike it with a hammer to remove the valve seat.

CAUTION:

When striking, the valve tips may break off on impact. Wear safety glasses to protect your eyes.



Hide 11176 3.REMOVE INJECTION NOZZLE SEAT

a.
A146574E01
1.346,1.329 1.639,1.578 0.293,0.249 10 SST 1.047,1.173 1.309,1.407 false

Using SST, remove the injection nozzle seat.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


b.

Remove the O-ring from the cylinder head sub-assembly.


Hide 11122 4.REMOVE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


b.
A146575E01
2.208,0.996 1.905,0.517 false 1.536,0.435 1.829,0.705 0.294,0.269 10 SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01070)
09950-70010  (09951-07100)


Hide 11126 5.REMOVE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


b.
A146576E01
1.505,0.394 1.8,0.656 0.295,0.262 10 SST 2.289,0.918 1.868,0.497 false

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01070)
09950-70010  (09951-07100)


Hide 11122 6.INSTALL INTAKE VALVE GUIDE BUSH

a.
A146571

Using a caliper gauge, measure the inside diameter of the guide bush hole.

Bush Hole Inside Diameter:

13.000 to 13.018 mm (0.5118 to 0.5125 in.)


HINT:

If the inside diameter of the cylinder head is greater than the maximum, replace the cylinder head.



b.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


c.
A146570E02
1.41,0.537 1.702,0.81 0.292,0.272 10 SST 2.191,1.032 1.791,0.623 false 0.624,1.744 0.81,1.932 0.185,0.188 10 *a

Using SST, tap in a new valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01070)
09950-70010  (09951-07100)

Protrusion Height:

26.4 to 26.8 mm (1.039 to 1.055 in.)


Text in Illustration
*a Protrusion Height

NOTICE:

Do not tap in the guide bush too much.



d.

Using a reamer, ream the inside of the valve guide bush to the specified oil clearance between the valve guide bush and valve stem.

Standard Oil Clearance:

0.028 to 0.058 mm (0.00110 to 0.00228 in.)



Hide 11126 7.INSTALL EXHAUST VALVE GUIDE BUSH

a.
A146571

Using a caliper gauge, measure the inside diameter of the guide bush hole.

Bush Hole Inside Diameter:

13.000 to 13.018 mm (0.5118 to 0.5125 in.)


HINT:

If the inside diameter of the cylinder head is greater than the maximum, replace the cylinder head.



b.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


c.
A146572E02
1.531,0.406 1.82,0.667 0.289,0.261 10 SST 2.256,0.877 1.895,0.493 false 1.387,1.682 1.582,1.855 0.195,0.173 10 *a

Using SST, tap in a new valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01070)
09950-70010  (09951-07100)

Protrusion Height:

26.4 to 26.8 mm (1.039 to 1.055 in.)


Text in Illustration
*a Protrusion Height

NOTICE:

Do not tap in the guide bush too much.



d.

Using a reamer, ream the inside of the valve guide bush to the specified oil clearance between the valve guide bush and valve stem.

Standard oil clearance:

0.053 to 0.083 mm (0.00209 to 0.00327 in.)



Hide 11176 8.INSTALL INJECTION NOZZLE SEAT

a.
A146565E03
2.336,0.216 2.525,0.379 0.189,0.163 10 *1 2.058,0.8 2.305,0.327 false 1.349,1.382 0.815,1.328 false 1.4,1.712 0.959,1.666 false 0.566,1.229 0.754,1.393 0.189,0.163 10 *2 0.724,1.574 0.913,1.737 0.189,0.163 10 *3

Apply a light coat of engine oil to a new O-ring, and install it into the cylinder head.

Text in Illustration
*1 Cylinder Head
*2 O-ring
*3 Injection Nozzle Seat

NOTICE:

Do not reuse the O-ring, as it may cause water or gas leakage inside the cylinder and the cylinder head may overheat or crack.



b.
A427411E01
1.063,2.667 1.583,2.781 false 0.885,2.573 1.198,2.771 0.313,0.198 10 false *1

Apply seal packing to a new injection nozzle seat.

Seal packing:

Three Bond 1211,1215 or equivalent


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the installation surface of the cylinder head and injection nozzle seat.

·

Do not reuse the injection nozzle seat, as it may cause water or gas leakage inside the cylinder and the cylinder may overheat or crack.




c.
A146567E03
0.904,0.235 1.202,0.497 0.298,0.261 10 SST 1.058,1.302 1.229,1.455 0.171,0.154 10 *1 1.283,1.401 1.583,1.486 false 1.282,0.333 1.582,0.418 false

Using SST, install the injection nozzle seat into the cylinder head.

SST
09260-69015  (09268-06020)

Text in Illustration
*1 Injection Nozzle Seat


d.
A146561E03
0.778,0.206 1.078,0.46 0.3,0.253 10 SST 1.128,1.61 1.312,1.794 0.184,0.184 10 *2 0.916,1.146 1.109,1.321 0.193,0.175 10 *1 1.58,1.501 1.15,1.255 false 1.693,1.869 1.359,1.717 false 1.582,0.544 1.152,0.298 false

Using SST, stake the injection nozzle seat.

SST
09260-69015  (09268-06010, 09268-06020)

Text in Illustration
*1 Injection Nozzle Seat
*2 SST (Steel Ball)

NOTICE:

Put a container under the cylinder head to prevent the steel ball from being lost.



Hide 11131 9.INSTALL INTAKE VALVE SEAT

a.
A146559E03
1.226,1.967 1.344,2.132 0.118,0.165 10 A 0.314,1.594 0.431,1.778 0.117,0.185 10 B

Using a caliper gauge and vernier caliper, measure the dimensions of the valve seat installation hole.

Cylinder Head Dimension:
A:

36.000 to 36.016 mm (1.4173 to 1.4179 in.)

B:

8.4 to 8.6 mm (0.3307 to 0.3386 in.)


If either result is not as specified, replace the cylinder head.


b.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


c.
A146564E04
0.896,1.375 0.438,0.646 0.438,0.646 0.854,1.542 false 2.313,0.792 2.688,0.906 false 2.344,1.125 2.74,1.333 false 2.344,1.469 2.594,1.438 false 2.323,1.781 2.677,1.583 false 2.354,2.115 2.813,1.625 false 0.26,0.438 0.552,0.708 0.292,0.271 10 false SST 1.927,0.708 2.333,0.979 0.406,0.271 10 false SST1 1.938,1.042 2.344,1.313 0.406,0.271 10 false SST2 1.938,1.406 2.344,1.677 0.406,0.271 10 false SST3 1.938,1.729 2.344,2 0.406,0.271 10 false SST4 1.938,2.042 2.344,2.313 0.406,0.271 10 false SST2

Using SST and a hammer, lightly tap the valve seat into the cylinder head.

SST
09950-60011  (09951-00300, 09951-00360, 09952-06010)
09950-70010  (09951-07100)

SST 1 09951-07100
SST 2 09952-06010
SST 3 09951-00360
SST 4 09951-00300


d.

Using SST and a hammer, completely tap in the valve seat.

SST
09950-60011  (09951-00300, 09951-00360, 09952-06010)
09950-70010  (09951-07100)


Hide 11135 10.INSTALL EXHAUST VALVE SEAT

a.
A146563E01
2.194,1.993 2.311,2.138 0.117,0.145 10 A 2.954,1.624 3.07,1.769 0.117,0.145 10 B

Using a caliper gauge and vernier caliper, measure the dimensions of the valve seat installation hole.

Cylinder Head Dimension:
A:

32.000 to 32.016 mm (1.2598 to 1.2605 in.)

B:

7.6 to 7.8 mm (0.2992 to 0.3071 in.)


If either result is not as specified, replace the cylinder head.


b.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


c.
A346893E01
2.271,0.656 2.594,0.802 false 0.552,1.479 0.198,0.667 0.198,0.667 0.563,1.313 true 2.292,0.948 2.646,1.073 false 2.271,1.198 2.469,1.177 false 2.281,1.448 2.542,1.354 false 2.302,1.917 2.698,1.396 false 0.083,0.479 0.542,0.677 0.458,0.198 10 false SST 1.885,0.552 2.344,0.75 0.458,0.198 10 false SST1 1.885,0.844 2.344,1.042 0.458,0.198 10 false SST2 1.885,1.125 2.344,1.323 0.458,0.198 10 false SST3 1.896,1.385 2.354,1.583 0.458,0.198 10 false SST4 1.917,1.854 2.375,2.052 0.458,0.198 10 false SST2

Using SST and a hammer, lightly tap the valve seat into the cylinder head.

SST
09950-60011  (09951-00250, 09951-00320, 09952-06010)
09950-70010  (09951-07100)

SST 1 09951-07100
SST 2 09952-06010
SST 3 09951-00320
SST 4 09951-00250


d.

Using SST and a hammer, completely tap in the valve seat.

SST
09950-70010  (09951-07100)
09950-60011  (09951-00250, 09951-00320, 09952-06010)