Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › ENGINE UNIT › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0356005 ENGINE UNIT G

N04C-VL ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 1.INSPECT VALVE ROCKER ARM OIL CLEARANCE

a.
A151466

Using a caliper gauge, measure the inside diameter of the rocker arm bush.

Standard Bush Inside Diameter:

22.023 to 22.052 mm (0.867 to 0.868 in.)


Maximum Bush Inside Diameter:

22.08 mm (0.869 in.)



b.
A151467

Using a micrometer, measure the outside diameter of the No. 1 valve rocker arm shaft sub-assembly.

Standard Shaft Diameter:

21.959 to 21.980 mm (0.8645 to 0.8653 in.)


Minimum Shaft Diameter:

21.92 mm (0.863 in.)



c.

Subtract the valve rocker arm inside diameter measurement from the valve rocker shaft outside diameter measurement.

Standard Oil Clearance:

0.043 to 0.093 mm (0.00169 to 0.00366 in.)


Maximum Oil Clearance:

0.15 mm (0.00591 in.)


If the oil clearance is greater than the maximum, replace the No. 1 valve rocker arm shaft sub-assembly and valve rocker arm bush.


Hide 13781 2.INSPECT VALVE PUSH ROD

a.

Place the push rod on V-blocks.


b.
A151468

Using a dial indicator, measure the circle runout at the center of the push rod.

Maximum Circle Runout:

0.30 mm (0.0118 in.)


If the circle runout is greater than the maximum, replace the push rod.


Hide 11101A 3.INSPECT CYLINDER HEAD SET BOLT

a.
A348669E02
2.135,2.708 2.448,2.906 0.313,0.198 10 false *a

Measure the length of the M12 head bolts (No. 1 to No. 18).

Standard Bolt Length (New Part):

126 mm (4.96 in.)


Maximum Length:

129 mm (5.08 in.)


Text in Illustration

If the length is greater than the maximum, replace the applicable bolts.

*a Measurement Length


Hide 4.INSPECT NO. 2 IDLE GEAR OIL CLEARANCE

a.
A151475

Using a cylinder gauge, measure the inside diameter of the No. 2 idle gear sub-assembly.

Standard Idle Gear Inside Diameter:

50.000 to 50.025 mm (1.9685 to 1.9695 in.)


Maximum Idle Gear Inside Diameter:

50.05 mm (1.9704 in.)



b.
A151476

Using a micrometer, measure the diameter of the No. 2 idle gear shaft.

Standard Idle Gear Shaft Diameter:

49.950 to 49.975 mm (1.9665 to 1.9675 in.)


Minimum Idle Gear Shaft Diameter:

49.95 mm (1.9665 in.)



c.

Subtract the No. 2 idle gear inside diameter measurement from the No. 2 idle gear shaft diameter measurement.

Standard Oil Clearance:

0.0125 to 0.0375 mm (0.00049 to 0.00148 in.)


Maximum Oil Clearance:

0.10 mm (0.00394 in.)


If the clearance is greater than the maximum, replace the No. 2 idle gear sub-assembly and No. 2 idle gear shaft.


Hide 5.INSPECT NO. 1 IDLE GEAR OIL CLEARANCE

a.
A151482

Using a cylinder gauge, measure the inside diameter of the No. 1 idle gear sub-assembly.

Standard Idle Gear Inside Diameter:

50.000 to 50.025 mm (1.9685 to 1.9695 in.)


Maximum Idle Gear Inside Diameter:

50.05 mm (1.9704 in.)



b.
A151483

Using a micrometer, measure the diameter of the No. 1 idle gear shaft.

Standard Idle Gear Shaft Diameter:

49.950 to 49.975 mm (1.9665 to 1.9675 in.)


Minimum Idle Gear Shaft Diameter:

49.95 mm (1.9665 in.)



c.

Subtract the No. 1 idle gear inside diameter measurement from the No. 1 idle gear shaft outside diameter measurement.

Standard Oil Clearance:

0.0125 to 0.0370 mm (0.000492 to 0.00146 in.)


Maximum Oil Clearance:

0.10 mm (0.00394 in.)


If the clearance is greater than the maximum, replace the No. 1 idle gear sub-assembly and No. 1 idle gear shaft.


Hide 13265 6.INSPECT CONNECTING ROD BOLT

a.
A151514E02
2.325,1.028 2.78,1.204 0.455,0.176 10 *a

Using a vernier caliper, measure the length of the connecting rod bolt.

Standard Bolt Length (New Part):

58.8 to 59.00 mm (2.315 to 2.323 in.)


Maximum Bolt Length:

61.5 mm (2.421 in.)


Text in Illustration

If the diameter is greater than the maximum, replace the connecting rod bolt.

*a Measurement Length


Hide 11462 7.INSPECT CYLINDER LINER

a.
A348670E02
1.646,0.948 1.927,1.427 false 1.854,1.469 2.167,1.667 0.313,0.198 10 false *1

Using a micrometer, measure the outside diameter of the cylinder liner.

Standard Diameter:
Symbols Outside Diameter
A 106.982 to 106.989 mm (4.2119 to 4.2122 in.)
B 106.990 to 106.995 mm (4.2122 to 4.2124 in.)
C 106.996 to 107.004 mm (4.2124 to 4.2128 in.)


Text in Illustration

If the diameter is less than the standard, replace the cylinder liner.

*1 Symbol


b.
A151518E03
0.381,0.308 0.606,0.49 0.225,0.181 10 *a 0.381,2.579 0.565,2.749 0.184,0.17 10 *b 2.742,2.48 2.925,2.652 0.183,0.172 10 *1 1.364,1.461 1.668,1.833 1.668,1.833 1.921,1.46 false 2.517,1.463 1.668,1.839 1.668,1.839 0.758,1.464 false 2.454,3.021 2.695,2.6 2.695,2.6 1.003,3.021 false 1.49,3.024 2.695,2.6 false 1.982,3.024 2.695,2.6 false 1.565,1.876 1.748,2.048 0.183,0.172 10 *1

Using a cylinder gauge, measure the inside diameter of the cylinder block.

Standard Diameter:
Symbols Inside Diameter
A 107.000 to 107.008 mm (4.2126 to 4.2129 in.)
B 107.008 to 107.014 mm (4.2129 to 4.2131 in.)
C 107.014 to 107.022 mm (4.2131 to 4.2135 in.)


Text in Illustration

If the diameter is greater than the standard, replace the cylinder block.

*1 Symbol
*a Cylinder Head Side
*b Intake Manifold Side


Hide 8.INSPECT CYLINDER BLOCK FOR WARPAGE

HINT:
A151525

Before the measurement, remove carbon deposits from the upper end inside the cylinder liner with a scraper or emery paper (recommended: No. 150), working in a circular direction. Make sure that there are no scratches inside the cylinder liner.


a.
A151526

Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head.

Maximum Warpage:

0.10 mm (0.00394 in.)


If the warpage is greater than the maximum, replace the cylinder block.


b.

Visually check the cylinders for vertical scratches.

If deep scratches are found, rebore all 4 cylinders. If necessary, replace the cylinder block.

NOTICE:

Do not adjust by grinding or polishing as the backlash of the timing gear will change.



Hide 9.INSPECT CYLINDER BORE

a.
A151527E06
1.708,3.438 1.885,3.594 0.177,0.156 10 true *a

Using a cylinder gauge, measure the cylinder liner inside diameter at the 4 points shown in the illustration.

Standard Inside Diameter:

104.012 to 104.036 mm (4.0950 to 4.0959 in.)


Maximum Inside Diameter:

104.15 mm (4.1004 in.)


Text in Illustration

If the diameter is greater than the maximum, replace the cylinder liner with a new one.

*a Measurement Point (80 mm (3.15 in.))


Hide 10.INSPECT PISTON

a.
A151528E07
1.063,2.823 1.229,2.969 0.167,0.146 10 true *a 2.021,3.781 2.198,3.948 0.177,0.167 10 true *b

Using a micrometer, measure the piston diameter at the point in the illustration.

Standard Piston Diameter:

103.936 to 103.952 mm (4.0920 to 4.0926 in.)


Text in Illustration
*a Diameter
*b Measurement Point (17 mm (0.669 in.))


Hide 11.INSPECT PISTON OIL CLEARANCE

a.

Subtract the piston diameter measurement from the cylinder liner inside diameter measurement.

Standard Oil Clearance:

0.06 to 0.10 mm (0.00236 to 0.00394 in.)


HINT:

Apply the value measured at the most worn point to the cylinder liner inside diameter.

If the clearance is outside the specified range, replace the cylinder liner and/or piston with a new one.



Hide 12.INSPECT RING GROOVE CLEARANCE

a.

Insert the piston ring into the piston ring groove.


b.
A151529

Using a feeler gauge, measure the clearance between the piston ring and piston ring groove.

Standard Groove Clearance:
Item Specified Condition

If the clearance is greater than the maximum, replace the piston or piston ring.

1st 0.11 to 0.15 mm (0.00433 to 0.00591 in.)
2nd 0.07 to 0.11 mm (0.00276 to 0.00433 in.)
Oil 0.02 to 0.06 mm (0.000787 to 0.00236 in.)



Hide 13.INSPECT PISTON RING END GAP

a.
E400144E01
2.146,1.479 2.458,1.677 0.313,0.198 10 false *a

Using a piston, push the piston ring a little beyond the bottom of the ring travel, 80 mm (3.15 in.) from the top of the cylinder block sub-assembly.

Standard End Gap:
Item Specified Condition
1st 0.3 to 0.45 mm (0.01181 to 0.01772 in.)
2nd 0.5 to 0.65 mm (0.01969 to 0.02559 in.)
Oil 0.15 to 0.3 mm (0.00591 to 0.01181 in.)


Text in Illustration

If the clearance is greater than the maximum, replace the piston ring.

*a 80 mm (3.15 in.)


Hide 14.INSPECT CONNECTING ROD SUB-ASSEMBLY

a.
A151534E02
1.354,1.667 1.771,1.25 false 1.198,1.656 1.51,1.854 0.313,0.198 10 false *a

Insert a stick with a diameter of 6 mm (0.24 in.) into the oil hole in the big end of the connecting rod and check that the tip of the stick comes out from the small end oil hole.

Text in Illustration

If there is any clogging, blow air through the lubrication passage using an air gun, or clean by inserting a wire.

*a Stick (6 mm (0.24 in.))


b.

Using a dye penetrant, check if there are any cracks on the connecting rod sub-assembly.


Hide 13411 15.INSPECT CRANKSHAFT

HINT:
A185159E02
1.091,0.643 1.249,0.789 0.158,0.146 10 *1 2.263,0.73 1.279,0.73 false

Before the inspection, clean the crankshaft with a commercial cleaning agent and clean the lubrication passage using an air gun.

Text in Illustration
*1 Air Gun


a.

Performing the dye penetrant test, check the crankshaft for cracks.

HINT:

Pay special attention to the finished R section and oil hole of the crankshaft journal and crankshaft pin.



b.

Visually check the crankshaft journal and pin for damage or wear.

If any damage is found, replace the crankshaft with a new one.


c.

Inspect for runout.

i.

Place the crankshaft on V-blocks.


ii.
A151540

Using a dial gauge, measure the circle runout of the crankshaft at the center journal.

Maximum Runout:

0.04 mm (0.00157 in.)


If the circle runout is greater than the maximum, replace the crankshaft with a new one.



d.
A151541

Using a micrometer, measure the main journal outside diameter.

Standard Journal Diameter:

72.94 to 72.96 mm (2.8717 to 2.8724 in.)


Maximum Taper and Out-of-Round:

0.01 mm (0.000394 in.)


Level of wear:

0.2 mm (0.00787 in.)


Wear limit:

1.2 mm (0.04724 in.)


HINT:
A151550E04
0.248,1.416 0.455,1.602 0.207,0.185 10 *a 1.898,1.421 2.112,1.586 0.214,0.166 10 *b 3.24,1.505 3.24,1.359 3.24,1.359 3.24,1.505 false 3.24,1.505 2.144,1.505 false 0.79,1.505 0.79,1.359 0.79,1.359 0.79,1.515 false 0.79,1.515 1.843,1.515 false 0.227,0.806 0.349,0.955 0.122,0.149 10 R

·

When the tapered level, out-of-round level, or wear limit is exceeded, use an undersized bearing and correct or re-polish until the oil clearance is 0.2 mm (0.00787 in.) or less (only carry out the correction/re-polishing if the oil clearance is over 0.2 mm (0.00787 in.) and under 1.2 mm (0.0472 in.)).

·

When the wear limit 1.2 mm (0.0472 in.) is exceeded, replace the crankshaft.

·

When polishing the crankshaft, adjust the fillet "R" dimensions to between 2.5 and 3.0 mm (0.0787 and 0.118 in.).


Text in Illustration
*a CORRECT
*b INCORRECT



e.
A151542

Using a micrometer, measure the crankshaft pin outside diameter.

Standard Diameter:

61.94 to 61.96 mm (2.4386 to 2.4394 in.)


Maximum Taper and Out-of-Round:

0.01 mm (0.000394 in.)


Level of wear:

0.2 mm (0.00787 in.)


Wear limit:

1.2 mm (0.04724 in.)


HINT:
A151550E04
0.248,1.416 0.455,1.602 0.207,0.185 10 *a 1.898,1.421 2.112,1.586 0.214,0.166 10 *b 3.24,1.505 3.24,1.359 3.24,1.359 3.24,1.505 false 3.24,1.505 2.144,1.505 false 0.79,1.505 0.79,1.359 0.79,1.359 0.79,1.515 false 0.79,1.515 1.843,1.515 false 0.227,0.806 0.349,0.955 0.122,0.149 10 R

·

When the tapered level, out-of-round level, or wear limit is exceeded, use an undersized bearing and correct or re-polish until the oil clearance is 0.2 mm (0.00787 in.) or less (only carry out the correction/re-polishing if the oil clearance is over 0.2 mm (0.00787 in.) and under 1.2 mm (0.0472 in.)).

·

When the wear limit 1.2 mm (0.0472 in.) is exceeded, replace the crankshaft.

·

When polishing the crankshaft, adjust the fillet "R" dimensions to between 2.5 and 3.0 mm (0.0787 and 0.118 in.).


Text in Illustration
*a CORRECT
*b INCORRECT



f.
A151543

Using a vernier caliper, measure the width of the crankshaft No. 4 journal.

Standard Width:

34.00 to 34.08 mm (1.3386 to 1.3417 in.)


Maximum Width:

34.48 mm (1.3574 in.)


If the width is greater than the maximum, replace the crankshaft.


g.

Using a dye penetrant, check if there are any cracks on the crankshaft.


h.

If any blockage is found, replace the crankshaft.


Hide 11416 16.INSPECT CRANKSHAFT BEARING CAP SET BOLT

a.
A151514E02
2.325,1.028 2.78,1.204 0.455,0.176 10 *a

Using a vernier caliper, measure the bearing cap bolt length.

Standard Bolt Length (New Part):

92.80 to 93.80 mm (3.6535 to 3.6929 in.)


Maximum Bolt Length:

95.00 mm (3.7401 in.)


Text in Illustration

If the length is longer than the maximum, replace the crankshaft bearing cap set bolt.

*a Measurement Length


Hide 17.INSPECT CRANKSHAFT OIL CLEARANCE

HINT:
A151548E02
0.48,1.802 0.651,1.949 0.17,0.147 10 *1 1.296,1.198 0.565,1.785 false

The upper bearings have an oil groove and oil hole, however, the lower bearings do not.

Text in Illustration
*1 Oil Hole


a.

Align the claw of the bearing with the claw groove of the cylinder block, and push in the upper bearing.

NOTICE:

Do not apply engine oil to the bearing and its contact surface.



b.
A151549

Align the claw of the bearing with the claw groove of the main bearing cap, and push in the lower bearing.

NOTICE:

Do not apply engine oil to the bearing and its contact surface.



c.
A151544E02
0.965,0.589 1.148,0.744 0.183,0.155 10 *a 1.153,2.762 1.314,2.917 0.161,0.155 10 *b 1.716,1.88 1.362,2.833 false 1.685,1.743 1.203,0.695 false

Install the thrust washer and bearing cap attached with bearing onto the cylinder block.

Text in Illustration
*a Front Mark
*b Journal No.


d.

Apply a light coat of engine oil to the threads and seat portion the heads of the bearing cap bolt.


e.
A151545E01
0.589,0.124 0.762,0.273 0.172,0.149 10 10 0.685,0.797 0.685,0.33 false 1.174,0.124 1.27,0.273 0.096,0.149 10 6 1.222,0.797 1.222,0.33 false 1.723,0.124 1.819,0.273 0.096,0.149 10 2 1.77,0.797 1.77,0.33 false 2.264,0.124 2.36,0.273 0.096,0.149 10 4 2.312,0.797 2.312,0.33 false 2.801,0.124 2.897,0.273 0.096,0.149 10 8 0.638,1.942 0.737,2.091 0.098,0.149 10 9 1.173,1.942 1.269,2.091 0.096,0.149 10 5 1.722,1.942 1.818,2.091 0.096,0.149 10 1 2.263,1.942 2.359,2.091 0.096,0.149 10 3 2.8,1.942 2.896,2.091 0.096,0.149 10 7 2.849,0.797 2.849,0.33 false 0.685,1.442 0.685,1.909 false 1.222,1.442 1.222,1.909 false 1.77,1.442 1.77,1.909 false 2.312,1.442 2.312,1.909 false 2.849,1.442 2.849,1.909 false

Uniformly tighten the 10 bolts, in 2 to 3 steps, in the order shown in the illustration.

Torque:

60 N*m (612 kgf*cm, 44 ft.*lbf)



f.

Loosen the bearing cap in the position of the thrust washer and use a plastic hammer to lightly tap the front and back ends of the crankshaft.


g.

Loosen the 10 bolts.


h.

Tighten the 10 bolts, in 2 to 3 steps, in the order shown in the illustration.

Torque:

60 N*m (612 kgf*cm, 44 ft.*lbf)



i.
A151546E02
1.802,0.233 2.042,0.383 0.24,0.15 10 60° 1.011,0.736 1.251,0.886 0.24,0.15 10 60° 1.173,1.692 1.36,1.845 0.187,0.153 10 *a 1.562,1.18 1.269,1.675 false

Mark the front side of the bolts with paint.

*a Paint Mark
V100135

Front


j.

Retighten the bolts by 60° in the same order as step (e).


k.

Perform step (g) again.


l.

Check that each painted mark is now at a 120° angle to the front.

NOTICE:

Do not loosen to return the bolts in position if they have been tightened too much.



m.
A151547E02
1.688,3.354 1.75,3.427 0.063,0.073 1.76,3.375 1.823,3.448 0.063,0.073 1.833,3.354 1.896,3.427 0.063,0.073 1.688,3.354 1.75,3.438 0.063,0.083 6 false X 1.76,3.375 1.823,3.458 0.063,0.083 6 false Y 1.833,3.354 1.896,3.438 0.063,0.083 6 false Z 1.865,2.927 2.094,3.073 0.229,0.146 10 true 45° 1.51,2.927 1.74,3.073 0.229,0.146 10 true 45°

Using a cylinder gauge, measure the crankshaft bearing inside diameter at 3 points (X, Y, Z in the illustration).

NOTICE:

Do not damage the crankshaft bearing.



n.

Subtract the crankshaft journal diameter measurement from the bearing inside diameter measurement.

Standard Oil Clearance:

0.051 to 0.102 mm (0.00201 to 0.00402 in.)


Maximum Oil Clearance:

0.20 mm (0.00787 in.)


If the oil clearance is greater than the maximum, use an undersize bearing and correct or regrind the crankshaft so that the oil clearance becomes 0.20 mm (0.0078 in.) or less.

Undersize Bearing Diameter:
Item Specified Condition
STD 72.94 to 72.96 mm (2.8717 to 2.8724 in.)
U/S 0.25 72.69 to 72.71 mm (2.8618 to 2.8626 in.)
U/S 0.50 72.44 to 72.46 mm (2.8520 to 2.8528 in.)
U/S 0.75 72.19 to 72.21 mm (2.8421 to 2.8429 in.)
U/S 1.00 71.94 to 71.96 mm (2.8323 to 2.8330 in.)


HINT:

Replace the upper and lower main bearings as one set.


i.
A151550E03
0.272,1.378 0.468,1.522 0.196,0.145 10 *a 1.889,1.458 2.062,1.603 0.173,0.145 10 *b 3.001,1.551 3.001,1.405 3.001,1.405 3.001,1.551 false 3.001,1.551 2.118,1.551 false 1.102,1.551 1.102,1.405 1.102,1.405 1.102,1.551 false 1.102,1.551 1.847,1.551 false 0.227,0.852 0.349,1.0 0.122,0.149 10 R

Machined dimension of file R

Main Crankshaft Journal:

2.50 to 3.00 mm (0.0984 to 0.1181 in.)


Text in Illustration
*a CORRECT
*b INCORRECT



Hide 18.INSPECT CONNECTING ROD BEARING OIL CLEARANCE

a.
A151551E02
2.869,0.791 3.03,0.266 false 3.047,0.161 3.237,0.313 0.19,0.152 10 *1

Align the claw of the bearing with the claw grooves of the connecting rod and connecting cap.

NOTICE:

Clean the back side of the bearing and the bearing surface of the connecting rod. The surface should be free of dust and oil.


Text in Illustration
*1 Claw


b.

Tighten the connecting rod bolts.

i.
A260710E03
1.219,0.74 1.604,1.188 0.385,0.448 1.219,1.219 1.604,1.656 0.385,0.438 1.604,0.99 2.604,0.99 false 1.583,1.417 2.083,1.417 2.083,1.417 2.083,1 false 2.635,0.896 2.948,1.094 0.313,0.198 10 false *a

Check the matchmarks, and install the bearing caps.

NOTICE:

Be careful of the installation direction of the bearing caps.


Text in Illustration
*a Matchmarks


ii.

Uniformly tighten the bolts in 2 to 3 steps.


iii.

Retighten the connecting rod bolts.

Torque:

30 N*m (306 kgf*cm, 22 ft.*lbf)



iv.
A151546E02
1.802,0.233 2.042,0.383 0.24,0.15 10 60° 1.011,0.736 1.251,0.886 0.24,0.15 10 60° 1.173,1.692 1.36,1.845 0.187,0.153 10 *a 1.562,1.18 1.269,1.675 false

Mark the front side of the bolts with paint.

Text in Illustration
*a Paint Mark
V100135

Front



c.

Retighten the bolts by 60° in the same order as step (b).


d.

Perform step (c) again.


e.
A151552

Using a cylinder gauge, measure the connecting rod big end inside diameter.

NOTICE:

Be careful not to damage the connecting rod bearing.



f.

Subtract the inside diameter measurement of the connecting rod from the diameter measurement of the crankshaft pin.

Standard Oil Clearance:

0.031 to 0.082 mm (0.0012 to 0.0032 in.)


Maximum Oil Clearance:

0.20 mm (0.0079 in.)


If the result is greater than the maximum, use an undersize bearing and correct or regrind the crankshaft so that the oil clearance becomes 0.2 mm (0.0079 in.) or less.

Under Size Bearing Diameter:
Item Specified Condition
STD 61.94 to 61.96 mm (2.4386 to 2.4394 in.)
U/S 0.25 61.69 to 61.71 mm (2.4287 to 2.4295 in.)
U/S 0.50 61.44 to 61.46 mm (2.4189 to 2.4197 in.)
U/S 0.75 61.19 to 61.21 mm (2.4090 to 2.4098 in.)
U/S 1.00 60.94 to 60.96 mm (2.3992 to 2.4000 in.)


i.
A151550E03
0.272,1.378 0.468,1.522 0.196,0.145 10 *a 1.889,1.458 2.062,1.603 0.173,0.145 10 *b 3.001,1.551 3.001,1.405 3.001,1.405 3.001,1.551 false 3.001,1.551 2.118,1.551 false 1.102,1.551 1.102,1.405 1.102,1.405 1.102,1.551 false 1.102,1.551 1.847,1.551 false 0.227,0.852 0.349,1.0 0.122,0.149 10 R

Machined dimension of file R

Crankshaft Pin:

2.50 to 3.00 mm (0.0984 to 0.1181 in.)


Text in Illustration
*a CORRECT
*b INCORRECT