Home › Engine / Hybrid System › N04C-VL (STARTING) › STARTER
RM2850E _51 Engine / Hybrid System _073166 N04C-VL STARTING _0356033 STARTER G

N04C-VL STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

NOTICE:

Each of the following tests must be performed within 3 to 5 seconds to prevent the coil from burning out.

Use a thick cable for carrying a large electric current.


A157286E04
1.958,1.167 2.625,1.167 false 2.198,0.615 2.448,0.615 2.448,0.615 2.854,0.844 false 3.094,1.219 3.552,2.563 3.552,2.563 3.719,2.563 false 2.052,0.521 2.271,0.708 0.219,0.188 10 false *b 3.719,2.469 3.917,2.667 0.198,0.198 10 false *c 1.792,1.073 2.063,1.292 0.271,0.219 10 false *a

Text in Illustration
*a Terminal C *b Terminal 50
*c Terminal 30 - -

a.

Perform operation test without load.

i.

Using a vise and aluminum protection plates, fix the starter assembly.


ii.

Connect the battery and an ammeter to the starter with terminal 30 disconnected, as shown in the illustration.

NOTICE:

Do not connect terminal 50 to the battery.


A157291E04
4.875,1.656 5.833,1.542 false 2.885,1.188 2.25,1.375 2.25,1.375 2.083,1.375 true 4.76,2.125 4.76,2.375 false 2.854,0.615 2.75,0.469 2.75,0.469 2.583,0.469 false 2.417,0.375 2.635,0.583 0.219,0.208 10 false *a 1.917,1.281 2.135,1.479 0.219,0.198 10 false *b 4.698,2.385 4.917,2.594 0.219,0.208 10 false *c

Text in Illustration
*a Terminal 50 *b Terminal 30
*c Body - -


iii.

Connect terminal 30 and terminal 50 to the battery and check that the starter rotates smoothly and steadily while the pinion gear is moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery - Terminal 30 11 V 200 A or less




Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.
A161634E02
1.802,1.406 1.042,1.729 1.042,1.729 1.896,1.51 false 0.833,1.646 1.063,1.854 0.229,0.208 10 false *a

Check the commutator for open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


Text in Illustration

If the result is not as specified, replace the starter armature assembly.

*a Segment



b.
A161635E03
1.792,1.417 1.167,1.667 1.167,1.667 0.917,1.667 false 2.688,0.885 3,0.417 3,0.417 3.167,0.417 false 0.75,1.563 0.969,1.771 0.219,0.208 10 false *a 3.177,0.333 3.406,0.552 0.229,0.219 10 false *b

Check the commutator for ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Commutator - Armature coil core Always 10 kΩ or higher


Text in Illustration

If the result is not as specified, replace the starter armature assembly.

*a Commutator
*b Armature Coil Core



c.

Check that the commutator is not dirty or burnt.

If dirty or burnt, restore it with sandpaper (No. 400) or replace the starter armature assembly.


d.
A161636

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

36.0 mm (1.42 in.)


Minimum diameter:

35.0 mm (1.38 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


e.
A115027

Using a vernier caliper, measure the undercut depth of the commutator.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)



f.
A154803

Check that the 2 bearings rotate smoothly.

If necessary, replace the starter armature assembly.


g.
A154804

Inspect the commutator for circle runout.

i.

Place the starter armature assembly on V-blocks.


ii.

Using a dial gauge, measure the circle runout.

Maximum circle runout:

0.05 mm (0.00197 in.)


If the circle runout is greater than the maximum, replace the starter armature assembly.



Hide 28120 3.INSPECT STARTER YOKE ASSEMBLY

a.
A161637E03
1.667,1.656 1.667,1.823 false 2.219,0.292 2.302,0.167 2.302,0.167 2.469,0.167 false 1.604,1.844 1.771,2 0.167,0.156 10 false *b 2.49,0.083 2.688,0.281 0.198,0.198 10 false *a

Check the field coil for open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal C - Brush Always Below 1Ω


Text in Illustration

If the result is not as specified, replace the starter yoke assembly.

*a Brush
*b Terminal C



b.
A161638E03
2.325,0.016 2.495,0.176 0.17,0.161 10 *1 1.9,1.976 2.07,2.137 0.17,0.161 10 *2 2.092,0.371 2.306,0.111 false 2.354,1.758 2.097,2.068 false

Check the field coil for ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Brush - Starter yoke body Always 10 kΩ or higher


Text in Illustration

If the result is not as specified, replace the starter yoke assembly.

*a Brush
*b Starter Yoke Body



Hide 4.INSPECT STARTER BRUSH

a.
A161639E03
0.705,1.977 0.871,2.132 0.166,0.155 10 *a 2.38,4.26 2.547,4.407 0.168,0.147 10 *a

Using a vernier caliper, measure the starter brush length.

Standard length:

21.0 mm (0.827 in.)


Minimum length:

12.0 mm (0.472 in.)


Text in Illustration

If the length is less than the minimum, replace the starter brush holder assembly and the starter yoke assembly.

*a Length

HINT:

Replace all 4 starter brushes at the same time.



Hide 28140 5.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A161640

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the starter brush holder assembly.

Positive brush holder - Negative brush holder Always 10 kΩ or higher




b.
A115032E07
2.229,1.344 2.552,0.833 2.552,0.833 2.625,0.833 false 1.042,1.813 1.375,1.813 false 0.875,1.708 1.042,1.875 0.167,0.167 10 false *a 2.677,0.74 2.844,0.906 0.167,0.167 10 false *b

Using a pull scale, measure the installed load of the spring at the exact moment the starter brush spring separates from the starter brush.

Standard spring installed load:

36 N (3.6 kgf, 8.0 lbf)


Minimum spring installed load:

12 N (1.2 kgf, 2.7 lbf)


Text in Illustration

If the installed load is less than the minimum, replace the starter brush spring.

*a Brush
*b Brush Spring


Hide 28011 6.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A161658E02
1.898,1.448 2.055,1.601 0.156,0.153 10 *b 1.115,0.809 1.277,0.959 0.162,0.15 10 *a

Check the starter clutch sub-assembly operation.

Text in Illustration
*a Lock
*b Free

i.

Hold the clutch and bearing with one hand and turn the shaft with the other.


ii.

Check that the inner sleeve turns easily in the "free" direction but cannot turn in the "lock" direction as shown in the illustration.

If the starter clutch sub-assembly does not operate as specified, replace the starter clutch sub-assembly.



Hide 28150 7.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A161641E04
0.921,0.017 1.105,0.177 0.184,0.159 10 *a 1.543,0.251 1.225,0.121 1.225,0.121 1.124,0.121 false 0.717,1.149 0.910,1.308 0.193,0.160 10 *b 1.55,0.579 1.072,1.248 1.072,1.248 0.937,1.248 false

Check the pull-in coil for open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1.0 Ω


Text in Illustration

If the result is not as specified, replace the magnet starter switch assembly.

*a Terminal 50
*b Terminal C



b.
A161642E05
1.896,1.896 1.813,1.896 1.813,1.896 1.646,1.646 false 0.646,0.302 0.979,0.302 false 0.479,0.208 0.677,0.365 0.198,0.156 10 false *a 1.938,1.813 2.135,1.969 0.198,0.156 10 false *b

Check the holding coil for open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Magnet Starter Switch Body Always Below 2.0 Ω


Text in Illustration

If the result is not as specified, replace the magnet starter switch assembly.

*a Terminal 50
*b Magnet Starter Switch Body