Home › Engine / Hybrid System › N04C-VL (STARTING) › STARTER
RM2850E _51 Engine / Hybrid System _073166 N04C-VL STARTING _0356033 STARTER A

N04C-VL STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28011 1.INSTALL STARTER CLUTCH SUB-ASSEMBLY

a.
A161660

Apply high temperature grease to the parts indicated by arrow marks in the illustration.

Text in Illustration
V100135

High Temperature Grease


b.

Install the starter clutch sub-assembly into the magnet starter switch assembly.

NOTICE:

Make sure that the bearing does not disengage from the clutch.



c.

Install the 3 starter washers and pinion drive lever with the snap ring.


Hide 28110 2.INSTALL STARTER DRIVE HOUSING ASSEMBLY

a.
A396405E02
1.167,0.146 1.333,0.146 1.333,0.146 1.625,0.333 true 2.531,1.135 2.865,1.135 false 1.021,0.073 1.333,0.271 0.313,0.198 10 false *a 2.875,1.01 3.188,1.208 0.313,0.198 10 false *1

Apply a light coat of seal packing to the surface of the starter drive housing assembly that contacts the magnet starter switch assembly.

Seal packing:

Three Bond 1121 or equivalent


Text in Illustration
*1 Starter Drive Housing Assembly
*a Seal Packing


b.
A161632

Install the starter drive housing assembly with the 2 bolts.

Torque:

6.0 N*m (61 kgf*cm, 53 in.*lbf)



Hide 28256 3.INSTALL STARTER INTERNAL GEAR

a.
A161649

Apply high temperature grease to the portion indicated by the arrow in the illustration.

Text in Illustration
V100135

High Temperature Grease


b.
A168833

Install the starter internal gear.

NOTICE:

Make sure the starter internal gear protrusion indicated by the arrow in the illustration is aligned with the groove on the bottom side of the magnet starter switch assembly.



c.
A161630E02
1.917,1.448 2.156,0.948 2.156,0.948 1.688,1.229 true 1.646,1.531 2.135,0.969 true 2.156,0.823 2.469,1.021 0.313,0.198 10 false *1

Apply high temperature grease to the 3 starter planetary gears.

Text in Illustration
*1 Starter Planetary Gears


d.

Install the 3 starter planetary gears.


Hide 28160 4.INSTALL STARTER ARMATURE ASSEMBLY

a.
A163701

Install the starter washer.

NOTICE:

Make sure that the starter washer is securely seated in the groove.



b.
A161650

Apply high temperature grease to the portion indicated by the arrow in the illustration.

Text in Illustration
V100135

High Temperature Grease


c.
A161628

Install the starter plate.


d.
A161647

Apply high temperature grease to the portion indicated by the arrow in the illustration.

Text in Illustration
V100135

High Temperature Grease


e.
A161627

Install the starter armature assembly to the magnet starter switch assembly.


Hide 28120 5.INSTALL STARTER YOKE ASSEMBLY

a.

Install 2 new rubber seals to the starter yoke assembly.


b.
A161626E03
0.615,1.813 0.781,1.813 0.781,1.813 1.729,0.729 true 1.969,0.75 2.469,0.667 2.469,0.667 2.635,0.667 false 2.677,0.573 2.99,0.771 0.313,0.198 10 false *a 0.448,1.719 0.76,1.917 0.313,0.198 10 false *b

Install the terminal to the terminal C.

Text in Illustration
*a Terminal
*b Terminal C


c.

Install the starter yoke assembly to the magnet starter switch assembly.


Hide 28140 6.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A161625E01
1.667,0.906 2.052,0.198 2.052,0.198 2.219,0.198 false 1.927,1.177 2.083,1.76 2.083,1.76 2.25,1.76 false 2.24,0.104 2.469,0.333 0.229,0.229 10 false *a 2.271,1.667 2.5,1.896 0.229,0.229 10 false *b

Place the starter brush holder assembly on the starter armature assembly.


b.

Using a screwdriver, hold the starter brush spring back and connect the 4 starter brushes to the starter brush holder assembly.

NOTICE:

Check that the positive(+) lead wires are not grounded.


Text in Illustration
*a Starter Brush Spring
*b Starter Brush


c.

Install the starter brush holder assembly into the starter armature assembly.


d.
A161651

Apply high temperature grease to the portion indicated by the arrow in the illustration.

Text in Illustration
V100135

High Temperature Grease


e.
A161624E03
0.917,0.667 1.083,0.667 1.083,0.667 1.406,0.594 false 0.75,0.594 0.917,0.74 0.167,0.146 10 false *a

Install the commutator end frame with the 2 screws.

Torque:

3.9 N*m (40 kgf*cm, 35 in.*lbf)



f.

Install the 2 through bolts.

Torque:

17 N*m (168 kgf*cm, 12 ft.*lbf)



g.

Install the nut to terminal C.

Torque:

21 N*m (214 kgf*cm, 15 ft.*lbf)


Text in Illustration
*a Terminal C


h.

Install the dust protector to commutator end frame.


Hide 28213 7.INSTALL STARTER CLUTCH PINION

a.
A163702

Using a snap ring pliers, Install the starter drive spring, starter clutch pinion and pinion stop nut with a new retainer.