Home › Engine / Hybrid System › 14B (ENGINE MECHANICAL) › CYLINDER BLOCK › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073170 14B ENGINE MECHANICAL _0356054 CYLINDER BLOCK A

14B ENGINE MECHANICAL  CYLINDER BLOCK  CYLINDER BLOCK INSPECTION  


PROCEDURE

Hide 1.CLEAN CYLINDER BLOCK

a.

Remove gasket material

Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.


b.
A420987

Clean cylinder block

Using a soft brush and solvent, thoroughly clean the cylinder block.


Hide 2.INSPECT TOP SURFACE OF CYLINDER BLOCK FOR FLATNESS

a.
A420988

Using a precision straight edge and feeler gauge, measure the surfaces contacting the cylinder head gasket for warpage.

Maximum warpage:

0.20 mm (0.0079 in.)


If warpage is greater than maximum, replace the cylinder block.


Hide 3.INSPECT CYLINDER FOR VERTICAL SCRATCHES

a.
A420989

Visually check the cylinder for vertical scratches.

If deep scratches are present, rebore all the 4 cylinders. If necessary, replace the cylinder block.


Hide 4.INSPECT CYLINDER BORE DIAMETER

HINT:
A420990

There are 3 sizes of the standard cylinder bore diameter, marked "1", "2" and "3" accordingly. The mark is stamped on the top of the cylinder block.


a.
A420991

Using a cylinder gauge, measure the cylinder bore diameter at positions A, B and C in the thrust and axial directions.

Standard diameter:
3B,14B
STD Mark "1" 102.000 - 102.010 mm (4.0157 - 4.0161 in.)
Mark "2 102.010 - 102.020 mm (4.0161 - 4.0165 in.)
Mark "3" 102.020 - 102.030 mm (4.0165 - 4.0169 in.)
O/S 0.50 102.500 - 102.530 mm (4.0354 - 4.0366 in.)
O/S 0.75 102.750 - 102.780 mm (4.0453 - 4.0464 in.)
O/S 1.00 103.000 - 103.030 mm (4.0551 - 4.0563 in.)

15B-F, 15B-FT
STD Mark "1" 108.000 - 108.010 mm (4.2520 - 4.2524 in.)
Mark "2 108.010 - 108.020 mm (4.2524 - 4.2528 in.)
Mark "3" 108.020 - 108.030 mm (4.2528 - 4.2531 in.)
O/S 0.50 108.500 - 108.530 mm (4.2717 - 4.2728 in.)
O/S 0.75 108.750 - 106.780 mm (4.2815 - 4.2827 in.)
O/S 1.00 109.000 - 109.030 mm (4.2913 - 4.2925 in.)


Maximum diameter:
3B,14B
STD 102.23 mm (4.0248 in.)
O/S 0.50 102.73 mm (4.0445 in.)
O/S 0.75 102.98 mm (4.0543 in.)
O/S 1.00 103.23 mm (4.0642 in.)

15B-F, 15B-FT
STD 108.23 mm (4.2610 in.)
O/S 0.50 108.73 mm (4.2807 in.)
O/S 0.75 108.98 mm (4.2906 in.)
O/S 1.00 109.23 mm (4.3004 in.)


If the diameter is greater than maximum, re bore all the 4 cylinders. If necessary, replace the cylinder block.


Hide 5.REMOVE CYLINDER RIDGE

a.
A420992

If the wear is less than 0.2 mm (0.008 in.), using a ridge reamer, grind the top of the cylinder.