Home › Engine / Hybrid System › 14B (STARTING) › STARTER › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073173 14B STARTING _0356067 STARTER A

14B STARTING  STARTER  MAGNETIC SWITCH TERMINAL KIT PARTS REPLACEMENT  


PROCEDURE

Hide 1.REMOVE MAGNETIC SWITCH END COVER

a.
A424346

Remove the nut, disconnect the lead wire from terminal C and remove the plate washer.


b.

Remove the 3 bolts and end cover from the magnetic switch assembly.


c.
A424347

Remove these parts from the magnetic switch assembly:

i.

Plunger


ii.

Return spring



Hide 2.INSPECT CONTACT PLATE FOR WEAR

a.
A424348

Using vernier calipers, measure the contact plate for depth of wear.

Maximum wear:

1.6 mm (0.063 in.)


If the depth of wear is greater than the maximum, replace the contact plate.


Hide 3.REMOVE TERMINAL KIT PARTS

a.
A424349

Using SST, remove the nut and washer.

SST
09810-38170  


b.
A424350

Remove these parts from the magnetic switch assembly (Terminal C):

i.

Terminal insulator outer


ii.

Terminal bolt


iii.

Contact plate


iv.

Terminal insulator inner



c.
A424351

Remove these parts from the magnetic switch assembly (Terminal 30):

i.

Terminal insulator outer


ii.

Packing


iii.

O-ring


iv.

Contact plate and terminal bolt


v.

Terminal insulator inner


vi.

Insulation paper



Hide 4.REINSTALL TERMINAL KIT PARTS (Terminal 30)

a.
A424352

Insert the insulation paper between the coil and housing.

HINT:

Install the insulation paper facing the correct direction as shown in the illustration.



b.
A424353

Install these parts to the magnetic switch assembly:

HINT:

Install the terminal insulator inner in the direction as shown in the illustration.


i.

Terminal insulator inner


ii.

Contact plate


iii.

Terminal bolt



c.
A424354

Install the O-ring on the terminal bolt.


d.

Place the packing to the terminal insulator outer, and install it to the terminal.

HINT:

Match the protrusion of the insulator with the indentation of the housing.



e.

Install the washer and nut, temporarily tighten the nut.


Hide 5.REINSTALL TERMINAL KIT PARTS (Terminal C)

a.
A424355

Install these parts to the magnetic switch assembly:

HINT:

Install the terminal insulator inner in the same direction as terminal 30.


i.

Terminal insulator inner


ii.

Contact plate


iii.

Terminal bolt


iv.

Terminal insulator outer



b.

Install the washer and nut, temporarily tighten the nut.


Hide 6. TIGHTEN TERMINAL NUT

a.
A424356

Put a wood block on the contact plate and press it down with a hand press.

Dimensions of wood block:

20 x 37 x 40 mm (0.79 x 1.46 x 1.57 in.)


Press force:

981 N (100 kgf, 221 lbf)


NOTICE:
·
A424357

Check the diameter of the hand press ram. Then calculate the gauge pressure of the press when 981 N (100 kgf, 221 lbf) of force is applied.

·

If the contact plate is not pressed down with the specified pressure, the contact plate may tilt due to coil deformation or the tightening of the nut.




b.
A420901

Using SST, tighten the nut to the specified torque.

SST
09810-38170  

Torque:

30 N*m (305 kgf*cm, 22 ft.*lbf)


NOTICE:

If the nut is over tightened, it may cause cracks on the inside of the insulator.



Hide 7.CLEAN CONTACT SURFACES OF CONTACT PLATE AND PLUNGER

a.
A420902

Clean the contact surfaces of the remaining contact plate and plunger with a dry shop rag.


Hide 8.REINSTALL MAGNETIC SWITCH END COVER

a.
A420903

Install these parts to the magnetic switch assembly:

i.

Return spring


ii.

Plunger



b.

Install the gasket and magnetic switch end cover with the 3 bolts.

Torque:

3.6 N*m (37 kgf*cm, 32 in.*lbf)



c.

Place the plate washer on terminal C, connect the lead wire to it and install the nut.

Torque:

21 N*m (215 kgf*cm, 16 ft.*lbf)