Home › Engine / Hybrid System › N04C-UH (ENGINE MECHANICAL) › ENGINE UNIT › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073174 N04C-UH ENGINE MECHANICAL _0356072 ENGINE UNIT A

N04C-UH ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12180E 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 11202D 2.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Remove the 2 bolts and the No. 2 cylinder head cover.


Hide 11202F 3.REMOVE CYLINDER HEAD COVER CUSHION RUBBER

a.

Remove the cylinder head cover cushion rubber from the No. 2 cylinder head cover.


Hide 11247 4.REMOVE CYLINDER HEAD COVER STAY

a.

Remove the 2 cylinder head cover stays from the No. 2 cylinder head cover.


Hide 11201 5.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Remove the 2 bolts and cylinder head cover sub-assembly.


b.

Remove the 2 cylinder head cover spacers from the cylinder head cover sub-assembly.


Hide 11228 6.REMOVE CYLINDER HEAD COVER CUSHION

a.

Remove the 2 cylinder head cover cushions from the cylinder head cover.


Hide 11213 7.REMOVE CYLINDER HEAD COVER GASKET

a.

Remove the cylinder head cover gasket from the cylinder head cover.


Hide 13901 8.REMOVE NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

A151464E11
1.917,1 1.563,0.292 false 1.906,1.115 1.448,1.927 false 1.406,0.208 1.583,0.385 0.177,0.177 10 false *1 1.24,1.865 1.417,2.042 0.177,0.177 10 false *2

Text in Illustration
*1 Adjusting Screw
*2 Lock Nut

a.

Loosen the lock nut at the top of the rocker arms, then turn out the adjusting screws completely.

NOTICE:

If the adjusting screws are not turned out, the rocker shaft may bend when the rocker arm support bolts are loosened.



b.
A151465E01
0.412,0.326 0.516,0.477 0.104,0.152 10 1 1.035,0.326 1.139,0.477 0.104,0.152 10 3 1.657,0.326 1.761,0.477 0.104,0.152 10 5 2.283,0.326 2.388,0.477 0.104,0.152 10 4 2.9,0.326 3.004,0.477 0.104,0.152 10 2

Loosen the 5 rocker arm support bolts in the order shown in the illustration.


c.

Remove the bolts and the No. 1 valve rocker shaft.


Hide 13781 9.REMOVE VALVE PUSH ROD

NOTICE:

Organize the parts so that each parts location can be remembered for reassembly.


Hide 13819 10.REMOVE VALVE BRIDGE

NOTICE:

Keep the removed parts in the correct order so that they can be returned to their original positions when reassembled.


Hide 11101 11.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.

Remove the cylinder head bolts in the order shown in the illustration.


b.

Lift and remove the cylinder head from the cylinder block.


c.

Remove the cylinder head gasket.


Hide 13751 12.REMOVE VALVE LIFTER

NOTICE:

Keep the removed parts in the correct order so that they can be returned to their original positions when reassembled.


Hide 13470 13.REMOVE CRANKSHAFT PULLEY ASSEMBLY

a.
A151470

Using a 46 mm socket wrench, remove the nut, spacer and pulley.

HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.



Hide 11351H 14.REMOVE FLYWHEEL HOUSIONG STAY RH

a.

Remove the 4 bolts and the flywheel housing stay.


Hide 11351G 15.REMOVE FLYWHEEL HOUSING LH STAY

a.

Remove the 4 bolts and the flywheel housing stay.


Hide 12311 16.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Remove the 4 bolts and the front No. 1 engine mounting bracket.


Hide 12315 17.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Remove the 4 bolts and the front No. 1 engine mounting bracket.


Hide 12101 18.REMOVE OIL PAN SUB-ASSEMBLY

a.
A000019

Remove the 26 bolts from the oil pan.


b.

Insert the blade of an oil pan seal cutter between the crankcase and oil pan. Cut through the applied sealer and remove the oil pan.

NOTICE:

Do not damage the contact surface of the cylinder block and oil pan.



Hide 15104 19.REMOVE OIL STRAINER SUB-ASSEMBLY

a.

Remove the 2 bolts and strainer.


b.

Remove the O-ring.


Hide 12270 20.REMOVE OIL SEPARATOR ASSEMBLY

a.

Remove the 5 bolts and remove the oil separator assembly.


b.

Remove the 2 O-rings.


Hide 21.REMOVE TIMING GEAR CASE

a.
A151471

Remove the 15 bolts.


b.

Using a screwdriver with its tip wrapped in protective tape, pry off the timing gear case.

NOTICE:

Do not damage the contact surfaces of the timing gear case, cylinder block and cylinder head.



Hide 11301C 22.REMOVE TIMING CHAIN OR BELT COVER OIL SEAL

A151472E09
0.564,2.512 0.733,2.676 0.169,0.165 10 *3 1.44,0.454 1.592,0.61 0.152,0.156 10 *1 2.875,2.346 3.041,2.499 0.166,0.153 10 *2 2.689,1.841 2.827,2.41 2.827,2.41 2.363,2.269 false 1.119,1.384 1.417,0.567 false 0.864,1.607 0.659,2.485 false

Text in Illustration
*1 Protective Tape
*2 Wooden Block
*3 Piece of Cloth

a.

Using a screwdriver with its tip wrapped in protective tape, pry out the oil seal.

HINT:

Use wooden blocks and a piece of cloth to prevent damage to the timing gear case.



Hide 23.INSPECT NO. 2 IDLE GEAR THRUST CLEARANCE

a.
A151473

Using a feeler gauge, measure the thrust clearance between the No. 2 idle gear thrust plate and No. 2 idle gear.

Standard Thrust Clearance:

0.103 to 0.164 mm (0.00406 to 0.00646 in.)


Maximum Thrust Clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is greater than the maximum, replace the No. 2 idle gear thrust plate and No. 2 idle gear.


Hide 24.INSPECT NO. 2 IDLE GEAR BACKLASH

a.
A157096

Using a dial indicator, measure the backlash between the No. 1 idle gear and No. 2 idle gear.

Standard Backlash:

0.036 to 0.227 mm (0.00142 to 0.00894 in.)


Maximum Backlash:

0.30 mm (0.0118 in.)


If the backlash is greater than the maximum, replace the No. 1 idle gear and No. 2 idle gear.


Hide 13572C 25.REMOVE NO. 2 IDLE GEAR THRUST PLATE

a.

Remove the 2 bolts and No. 2 idle gear thrust plate.


Hide 13508N 26.REMOVE NO. 2 IDLE GEAR SUB-ASSEMBLY

Hide 13581C 27.REMOVE NO. 2 IDLE GEAR SHAFT

a.

Remove the 2 bolts and No. 2 idle gear shaft.


b.

Remove the O-ring.


Hide 13577D 28.REMOVE LOCK PLATE

a.

Remove the 3 bolts and plate from the end plate.


Hide 29.INSPECT CAMSHAFT TIMING GEAR BACKLASH

a.
A151477

Using a dial indicator, measure the backlash between the camshaft timing gear and No. 1 idle gear.

Standard Backlash:

0.069 to 0.203 mm (0.00272 to 0.00799 in.)


Maximum Backlash:

0.30 mm (0.0118 in.)


If the backlash is greater than the maximum, replace the camshaft timing gear and No. 1 idle gear.


Hide 13501 30.REMOVE CAMSHAFT

a.

Remove the 2 bolts, thrust plate and camshaft.


Hide 31.INSPECT OIL PUMP GEAR BACKLASH

a.

Using a dial indicator, measure the backlash between the oil pump gear and No. 1 idle gear.

Standard Backlash:

0.065 to 0.215 mm (0.00256 to 0.00846 in.)


Maximum Backlash:

0.30 mm (0.0118 in.)


If the backlash is greater than the maximum, replace the pump and No. 1 idle gear.


Hide 32.INSPECT NO. 1 IDLE GEAR THRUST CLEARANCE

a.
A151479

Using a feeler gauge, measure the thrust clearance between the No. 1 idle gear thrust plate and No. 1 idle gear.

Standard Thrust Clearance:

0.103 to 0.164 mm (0.00406 to 0.00646 in.)


Maximum Thrust Clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is greater than the maximum, replace the No. 1 idle gear thrust plate and No. 1 idle gear.


Hide 33.INSPECT NO. 1 IDLE GEAR BACKLASH

a.
A151480

Using a dial indicator, measure the backlash between the crankshaft timing gear and No. 1 idle gear.

Standard Backlash:

0.035 to 0.193 mm (0.00138 to 0.00760 in.)


Maximum Backlash:

0.30 mm (0.0118 in.)


If the backlash is greater than the maximum, replace the crankshaft timing gear and No. 1 idle gear.


Hide 13581B 34.REMOVE NO. 1 IDLE GEAR SHAFT

a.
A151481E01
1.762,1.786 2.057,1.932 0.295,0.146 10 SST 1.706,1.31 1.932,1.752 1.932,1.752 2.206,1.195 false 1.93,1.293 1.932,1.752 false

Remove the bolt.


b.

Using SST, remove the No. 1 idle gear shaft.

SST
09910-00015  (09911-00011, 09912-00010)

NOTICE:

When removing the gear shaft, hold the No. 1 idle gear to prevent the No. 1 gear and No. 1 idle gear thrust plate from falling.



Hide 13508M 35.REMOVE NO. 1 IDLE GEAR SUB-ASSEMBLY

Hide 13572B 36.REMOVE NO. 1 IDLE GEAR THRUST PLATE

Hide 37.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

A430683E01
1.083,0.708 1.427,1.167 false 0.865,0.521 1.323,0.719 0.458,0.198 10 false SST 0.323,0.896 0.552,1.104 0.229,0.208 10 false *a 1.771,1.708 2,1.917 0.229,0.208 10 false *b

Text in Illustration
*a Hold
*b Turn Clockwise

a.

Using SST, remove the crankshaft timing gear or sprocket.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051)


Hide 15100 38.REMOVE OIL PUMP ASSEMBLY

a.

Remove the 7 bolts and oil pump.


Hide 15119 39.REMOVE OIL PUMP COVER GASKET

a.

Remove the gasket from the oil pump.


Hide 11311H 40.REMOVE FRONT END PLATE

a.
A151485

Remove the 4 bolts and front end plate.


Hide 11312 41.REMOVE FRONT END PLATE GASKET

a.

Remove the front end plate gasket from the front end plate.


Hide 13450A 42.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A151486

Temporarily install 4 bolts in the positions of the cylinder block shown in the illustration to prevent the wires from sliding toward the center of the block.


b.

Attach 2 wires to the cylinder block.

HINT:

The wires must be attached to the outside of the installed bolts.



c.

Using a chain block and an engine sling device, remove the cylinder block from the engine stand.


d.
A151487E02
2.685,0.311 2.875,0.472 0.189,0.161 10 *1 1.175,2.706 1.379,2.869 0.204,0.163 10 *2 0.719,2.304 1.264,2.674 1.264,2.674 1.787,2.326 false 2.442,1.089 2.648,0.397 false

Place the cylinder block on wooden blocks on a workbench.

Text in Illustration
*1 Flywheel Housing
*2 Wooden Block


e.

Remove the 4 bolts from the cylinder block.


f.
A151470

Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.


g.
A151488E01
1.665,0.749 1.772,0.901 0.108,0.153 10 1 1.45,0.877 1.546,1.029 0.096,0.153 10 6 1.444,1.132 1.54,1.275 0.096,0.143 10 4 1.671,1.261 1.768,1.413 0.097,0.153 10 2 1.893,1.133 1.99,1.285 0.096,0.153 10 5 1.894,0.872 1.99,1.025 0.096,0.153 10 3

Uniformly loosen and remove the 6 bolts in the order shown in the illustration.


h.

Remove the flywheel.

NOTICE:

The flywheel is heavy. When removing, be careful not to drop it.



Hide 13453 43.REMOVE FLYWHEEL RING GEAR

a.
A151489

Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

NOTICE:

Be careful not to overheat the ring gear.


CAUTION:

Do not touch the ring gear and flywheel while they are hot.



b.
A151490

Using a brass bar and hammer, uniformly strike all around the ring gear and remove the gear.

CAUTION:

After removing, allow the ring gear to cool before handling.



Hide 11351 44.REMOVE FLYWHEEL HOUSING

a.

Remove the 14 bolts from the cylinder block.


b.

Using a screwdriver with its tip wrapped in protective tape, pry off the flywheel housing.


Hide 11381A 45.REMOVE REAR ENGINE OIL SEAL

A151491E05
2.206,2.848 2.372,2.995 0.166,0.147 10 *3 0.361,2.918 0.569,3.095 0.208,0.177 10 *2 2.711,0.182 2.9,0.36 0.189,0.177 10 *1 0.294,2.156 0.477,2.878 0.477,2.878 0.866,2.729 false 1.752,1.514 2.685,0.279 false 1.594,1.876 2.263,2.817 false

Text in Illustration
*1 Protective Tape
*2 Wooden Block
*3 Piece of Cloth

a.

Using a screwdriver with its tip wrapped in protective tape, pry out the rear engine oil seal.

HINT:

Use wooden blocks and a piece of cloth to prevent damage to the flywheel housing.



Hide 46.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A151513

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard Thrust Clearance:

0.200 to 0.520 mm (0.00787 to 0.0205 in.)


Maximum Thrust Clearance:

0.60 mm (0.0236 in.)


If the thrust clearance is greater than the maximum, replace the connecting rod. If necessary, replace the crankshaft.


Hide 47.REMOVE PISTON WITH CONNECTING ROD

a.

Remove the piston with connecting rod from the cylinder block.


Hide 13260 48.REMOVE CONNECTING ROD SUB-ASSEMBLY

Hide 11462 49.REMOVE CYLINDER LINER

A151515E13
2.292,1.635 2.448,1.781 0.156,0.146 10 false *a

Text in Illustration
*a Matchmarks

HINT:

Before removing the cylinder liner, put matchmarks on the cylinder liner and cylinder block.


NOTICE:

When reusing the cylinder liner, misalignment with the cylinder block may concentrate stress on the thin part of the cylinder liner and it may break.


a.
A151516E01
0.445,0.608 0.743,0.761 0.299,0.153 10 SST 1.258,0.814 0.813,0.693 false

Using SST, remove the cylinder liner.

SST
S0942-01460  

NOTICE:

Keep the removed parts in the correct order so that they can be returned to their original positions when reassembled.



Hide 50.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A151519

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard Thrust Clearance:

0.050 to 0.220 mm (0.00197 to 0.00866 in.)


Maximum Thrust Clearance:

0.40 mm (0.0157 in.)


If the thrust clearance is greater than the maximum, replace the crankshaft or thrust washers as a set.


Hide 13411 51.REMOVE CRANKSHAFT

a.
A151520E01
2.902,0.104 3.011,0.253 0.109,0.149 10 2 2.959,0.778 2.959,0.291 false 2.368,0.104 2.478,0.253 0.109,0.149 10 6 2.425,0.778 2.425,0.291 false 1.786,0.104 1.958,0.253 0.172,0.149 10 10 1.877,0.778 1.877,0.291 false 1.274,0.104 1.383,0.253 0.109,0.149 10 8 1.331,0.778 1.331,0.291 false 0.74,0.104 0.849,0.253 0.109,0.149 10 4 2.901,1.906 3.01,2.056 0.109,0.149 10 1 2.368,1.906 2.477,2.056 0.109,0.149 10 5 1.837,1.906 1.949,2.056 0.113,0.149 10 9 1.273,1.906 1.382,2.056 0.109,0.149 10 7 0.739,1.906 0.848,2.056 0.109,0.149 10 3 0.797,0.778 0.797,0.291 false 0.797,1.394 0.797,1.881 false 1.33,1.394 1.33,1.881 false 1.878,1.394 1.878,1.881 false 2.425,1.394 2.425,1.881 false 2.959,1.394 2.959,1.881 false

Remove the 10 bearing cap bolts in the order shown in the illustration.


b.

Using a plastic-faced hammer, tap the bearing caps to remove them.

NOTICE:

Be careful not to damage the thrust washers and bearings.



c.

Remove the crankshaft.


Hide 11011 52.REMOVE CRANKSHAFT THRUST WASHER SET

NOTICE:

Organize the parts so that each parts location can be remembered for reassembly.


Hide 11702 53.REMOVE CRANKSHAFT BEARING SET

NOTICE:

Organize the parts so that each parts location can be remembered for reassembly.


Hide 15605 54.REMOVE OIL CHECK VALVE SUB-ASSEMBLY

a.

Remove the bolt, the oil check valve and gasket.


Hide 15708 55.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Remove the bolt and the No. 1 oil nozzle.


Hide 13011 56.REMOVE PISTON RING SET

a.
A151521

Using a piston ring expander, remove the piston rings.

HINT:

Arrange the piston rings in the correct order.



Hide 13101A 57.REMOVE PISTON PIN HOLE SNAP RING

a.
A151522

Using snap ring pliers, remove the snap rings.


Hide 58.REMOVE PISTON

a.
A151523

Gradually heat the piston to approximately 50°C (122°F).


b.
A151524

Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

NOTICE:
·

The piston and pin are a set.

·

Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.




Hide 59.REMOVE STUD BOLT

Hide 60.INSPECT PISTON PIN OIL CLEARANCE

a.
A151531

Using a micrometer, measure the piston pin diameter.

Standard Piston Pin Diameter:

36.989 to 37.000 mm (1.4563 to 1.4567 in.)


Minimum Piston Pin Diameter:

36.96 mm (1.4551 in.)


If the diameter is less than the minimum, replace the piston pin with a new one.

HINT:

Never grind the piston pin, because the surface is coated with a special material.



b.
A151532

Using a cylinder gauge, measure the connecting rod bush inside diameter.

Standard Bush Inside Diameter:

37.035 to 37.045 mm (1.4581 to 1.4585 in.)


Maximum Bush Inside Diameter:

37.10 mm (1.4606 in.)


If the inside diameter is greater than the maximum, replace the connecting rod bush with a new one.


c.

Subtract the diameter measurement of the piston pin from the inside diameter measurement of the connecting rod bush.

Standard Oil Clearance:

0.035 to 0.056 mm (0.00138 to 0.00220 in.)


Maximum Oil Clearance:

0.08 mm (0.00315 in.)


If the oil clearance is greater than the maximum, replace the piston with a new one.


d.
A151533E04
2.74,1.156 2.885,1.479 false 2.76,1.49 2.99,1.667 0.229,0.177 10 true 90°

Using a cylinder gauge, measure the piston pin hole inside diameter while turning the gauge 90°.

Standard Piston Pin Hole Inside Diameter:

36.987 to 37.003 mm (1.4562 to 1.4568 in.)


Maximum Piston Pin Hole Inside Diameter:

37.05 mm (1.4587 in.)


If the piston pin hole inside diameter is greater than the maximum, replace the piston with a new one.


e.

Subtract the diameter measurement of the piston pin from the inside diameter measurement of the piston pin hole.

Standard Oil Clearance:

-0.013 to 0.014 mm (-0.000512 to 0.000551 in.)


Maximum Oil Clearance:

0.05 mm (0.00197 in.)


If the clearance is greater than the maximum, replace the piston or piston pin.


Hide 13201A 61.REMOVE CONNECTING ROD SMALL END BUSH

a.
A151666E12
0.885,0.708 1.24,1.302 false 0.521,1.688 0.26,2.521 false 2.25,1.688 2.073,2.073 false 1.896,2.083 2.229,2.26 0.333,0.177 10 false SST 0.729,0.542 1.031,0.698 0.302,0.156 10 false SST 0.125,2.552 0.469,2.729 0.344,0.177 10 false SST

Prepare SST.

SST
S0940-21450  
S0948-11130  
S9233-10360  

i.

Assemble the guide and press sub-assembly by inserting its pin into the guide, then secure them with the wing nut.

HINT:

Orient the letter W, stamped on the guide, above the pin.



ii.
A151536E13
2.719,1.469 2.646,1.719 false 1.01,1.365 0.917,1.719 false 2.094,0.844 1.802,0.354 false 1.698,0.198 1.875,0.375 0.177,0.177 10 false *1 2.563,1.74 2.74,1.917 0.177,0.177 10 false *3 0.833,1.74 1.021,1.885 0.188,0.146 10 false *2

Align both supporting surfaces of the guide and press sub-assembly flatly on an even plane.

Text in Illustration
*1 Connecting Rod
*2 Guide
*3 Press Sub-assembly



b.

Using the SST, remove the bush.

i.

Set the connecting rod assembled without connecting rod bearing on the guide and press sub-assembly.


ii.
A151537E02
2.536,0.43 3.026,0.6 0.49,0.17 10 *2 2.536,0.953 2.876,1.099 0.34,0.146 10 *3 0.69,1.505 0.86,1.651 0.17,0.146 10 *5 0.672,0.444 0.859,0.59 0.187,0.146 10 *1 2.528,1.457 2.734,1.619 0.206,0.162 10 *4 2.131,2.528 2.306,2.713 0.176,0.184 10 *6 2.12,0.681 2.513,0.538 false 2.102,1.192 2.506,1.046 false 2.223,1.437 2.488,1.527 false 1.922,2.174 2.202,2.493 false 0.907,1.59 1.549,1.356 false 1.592,0.795 0.905,0.538 false

Using SST, install the spindle into the bush.

SST
S0940-21470  

Text in Illustration
*1 Groove
*2 Spindle
*3 Bush
*4 Connecting Rod
*5 Oil Hole
*6 Press Sub-assembly

HINT:

Align the groove of the spindle with the oil hole of the bush.



iii.
A151538E03
1.765,0.303 1.944,0.47 0.179,0.168 10 *1 1.066,0.556 1.233,0.724 0.166,0.168 10 *2 1.686,1.067 1.279,0.659 false 2.293,0.707 1.999,0.413 false

Using a press, remove the bush.

Text in Illustration
*1 Spindle
*2 Connecting Rod
V100135

Press

HINT:

Always operate the press slowly and smoothly.




Hide 62.INSPECT CAMSHAFT OIL CLEARANCE

a.
A151658

Measure the oil clearance of the camshaft journal.

i.

Using a micrometer, measure the camshaft journal outside diameter.

Standard Journal Outside Diameter::
Journal No. Specified Condition
No. 1 56.95 to 56.97 mm (2.2421 to 2.2429 in.)
No. 2 56.75 to 56.77 mm (2.2343 to 2.2350 in.)
No. 3 56.55 to 56.57 mm (2.2264 to 2.2272 in.)


If the outside diameter is outside the specified range, replace the camshaft.


ii.
A151659

Using a cylinder gauge, measure the camshaft bearing inside diameter.

Standard Inside Diameter:
Journal No. Specified Condition
No. 1 57.035 to 57.135 mm (2.2455 to 2.2494 in.)
No. 2 56.835 to 56.935 mm (2.2376 to 2.2415 in.)
No. 3 56.635 to 56.735 mm (2.2297 to 2.2337 in.)


If the inside diameter is outside the specified range, replace the camshaft bearing.


iii.

Subtract the outside diameter measurement of the camshaft journal from the inside diameter measurement of the camshaft bearing.

Standard Oil Clearance:

0.030 to 0.120 mm (0.00118 to 0.00472 in.)


Maximum Oil Clearance:

0.15 mm (0.00591 in.)


If the oil clearance is greater than the maximum, replace the camshaft or camshaft bearing.



Hide 63.REMOVE CAMSHAFT BEARING

A151660E03
0.671,0.406 1.036,0.552 0.365,0.145 10 No. 1 0.384,1.616 0.679,1.761 0.295,0.145 10 SST 1.66,0.406 2.025,0.552 0.365,0.145 10 No. 2 2.607,0.406 2.972,0.552 0.365,0.145 10 No. 3 0.556,1.596 0.556,1.329 false

Text in Illustration
V100135

Front

a.

Using SST, remove the camshaft bearings in the directions indicated by the arrow marks in the illustration.

SST
09215-00101  (09215-00130, 09215-00141, 09215-00150, 09215-00161)
09215-00013  (09215-00021, 09215-00461)

NOTICE:

Remove the bearings No. 1, No. 2 and No. 3 in order.