Home › Engine / Hybrid System › N04C-UH (ENGINE MECHANICAL) › ENGINE UNIT
RM2850E _51 Engine / Hybrid System _073174 N04C-UH ENGINE MECHANICAL _0356072 ENGINE UNIT A

N04C-UH ENGINE MECHANICAL  ENGINE UNIT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:

There are 2 methods to replace the timing chain or belt cover oil seal.


PROCEDURE

Hide 11301C 1.REPLACE TIMING CHAIN OR BELT COVER OIL SEAL

a.
A151472E09
0.564,2.512 0.733,2.676 0.169,0.165 10 *3 1.44,0.454 1.592,0.61 0.152,0.156 10 *1 2.875,2.346 3.041,2.499 0.166,0.153 10 *2 2.689,1.841 2.827,2.41 2.827,2.41 2.363,2.269 false 1.119,1.384 1.417,0.567 false 0.864,1.607 0.659,2.485 false

If the timing gear case is removed from the cylinder block:

Text in Illustration
*1 Protective Tape
*2 Wooden Blocks
*3 Piece of Cloth

i.

Using a screwdriver with its tip wrapped in protective tape, pry out the oil seal.

HINT:

Use wooden blocks and a piece of cloth to prevent damage to the timing gear case.



ii.
A151503E01
2.028,1.656 2.34,1.798 0.313,0.142 10 SST 1.724,1.167 2.183,1.627 false

Using SST and a hammer, tap in a new oil seal to the timing gear case so that oil seal is flush with the timing gear edge.

SST
09223-78010  

NOTICE:
·

Be careful not to tap the oil seal at an angle.

·

Keep the gap between the gear case edge and the oil seal free of foreign matter.




iii.

Apply MP grease to the oil seal lip.



b.
A151470

If the timing gear case is installed onto the cylinder block:

i.

Using a 46 mm socket wrench, remove the nut, spacer and crankshaft pulley.

HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.



ii.
A152900E03
1.26,1.705 1.45,1.87 0.19,0.165 10 *1 1.472,1.231 1.355,1.668 false

Using a screwdriver with its tip wrapped in protective tape, pry out the oil seal.

Text in Illustration
*1 Protective Tape


iii.
A152899E01
1.288,2.575 1.593,2.726 0.304,0.152 10 SST 1.659,1.906 1.487,2.549 false

Using SST and a hammer, tap in a new oil seal into the timing gear case so that oil seal is flush with the timing gear edge.

SST
09223-78010  

NOTICE:
·

Be careful not to tap the oil seal at an angle.

·

Keep the gap between the gear case edge and the oil seal free of foreign matter.




iv.

Apply MP grease to the oil seal lip.


v.
A151470

Install the pulley and spacer onto the crankshaft.

HINT:

Align the pulley set key with the key groove of the pulley.



vi.

Using a 46 mm socket wrench, tighten the nut.

Torque:

100 N*m (1020 kgf*cm, 74 ft.*lbf)


HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.



vii.
A187774E01
1.102,0.517 1.498,0.677 0.396,0.16 10 90° 1.246,1.538 1.576,1.718 0.33,0.181 10 *a 1.626,1.153 1.598,1.191 1.598,1.191 1.551,1.257 false 1.551,1.257 1.377,1.499 false

Mark the front side of the nut with paint as shown in the illustration.

Text in Illustration
*a Paint Mark
V100135

Right Side of Engine


viii.

Retighten the nut by 90°.



Hide 11381A 2.REPLACE REAR ENGINE OIL SEAL

A151491E05
2.206,2.848 2.372,2.995 0.166,0.147 10 *3 0.361,2.918 0.569,3.095 0.208,0.177 10 *2 2.711,0.182 2.9,0.36 0.189,0.177 10 *1 0.294,2.156 0.477,2.878 0.477,2.878 0.866,2.729 false 1.752,1.514 2.685,0.279 false 1.594,1.876 2.263,2.817 false

Text in Illustration
*1 Protective Tape
*2 Wooden Blocks
*3 Piece of Cloth

a.

Using a screwdriver with its tip wrapped in protective tape, pry out the oil seal.


b.
A151492E06
1.604,1 2.938,0.49 false 2.99,0.365 3.313,0.563 0.323,0.198 10 true SST 2.573,1.635 2.729,1.792 0.156,0.156 10 false *a

Using SST and a hammer, tap in a new oil seal until it is 4 mm (0.157 in.) below the upper edge of the flywheel housing.

Text in Illustration
*a 4 mm (0.157 in.)

SST
09223-78010  

NOTICE:
·

Be careful not to tap the oil seal at an angle.

·

Keep the gap between the rear oil seal retainer edge and the oil seal free of foreign matter.




c.

Apply MP grease to the oil seal lip.


Hide 3.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.

Remove the 7 straight pins.


b.

Using a plastic-faced hammer, install 7 new straight pins.

Standard Protrusion Height:
Item Specified Condition
A 6.0 mm (0.236 in.)
B 13.0 mm (0.512 in.)
C 16.0 mm (0.630 in.)
D 6.0 mm (0.236 in.)


A151663E10
0.49,1.365 1.208,1.167 false 1.604,0.625 2.167,1.365 2.167,1.365 0.865,2 false 6.375,1.667 5.688,2.031 5.688,2.031 4.885,1.677 false 3.323,1.094 4.208,1.469 4.208,1.469 3.865,1.948 false 1.333,0.156 1.51,0.323 0.177,0.167 10 false *a 0.354,1.302 0.531,1.51 0.177,0.208 10 false A 2.208,1.292 2.365,1.49 0.156,0.198 10 false B 5.646,2.063 5.813,2.26 0.167,0.198 10 false D 4.26,1.385 4.427,1.583 0.167,0.198 10 false C 0.927,3.656 1.104,3.813 0.177,0.156 10 false A 2.531,3.917 2.688,4.115 0.156,0.198 10 false B 4.271,3.885 4.438,4.083 0.167,0.198 10 false C 5.917,3.76 6.083,3.958 0.167,0.198 10 false D 0.49,2.625 1.542,2.802 1.052,0.177 10 false 5 mm (0.197 in.) 1.25,3.229 1.917,3.583 0.667,0.354 10 false 10 mm (0.394 in.) 2.021,2.375 3.104,2.563 1.083,0.188 10 false 8 mm (0.315 in.) 2.99,3.25 3.656,3.625 0.667,0.375 10 false 24 mm (0.945 in.) 3.74,2.385 4.906,2.573 1.167,0.188 10 false 12 mm (0.472 in.) 5.469,2.521 6.531,2.708 1.063,0.188 10 false 8 mm (0.315 in.) 6.375,3.208 7.031,3.573 0.656,0.365 10 false 16 mm (0.630 in.) 4.75,3.25 5.417,3.615 0.667,0.365 10 false 24 mm (0.945 in.) 3.313,0.156 3.49,0.323 0.177,0.167 10 false *b 5.573,0.156 5.75,0.323 0.177,0.167 10 false *c 4.292,4.615 4.469,4.781 0.177,0.167 10 false *d

Text in Illustration
*a Front Side *b Rear Side
*c Cylinder Head Side *d Protrusion Height