Home › Engine / Hybrid System › N04C-UH (ENGINE MECHANICAL) › DRIVE BELT
RM2850E _51 Engine / Hybrid System _073174 N04C-UH ENGINE MECHANICAL _0356074 DRIVE BELT A

N04C-UH ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

A146502E08
2.167,1.25 1.76,1.26 false 2.177,1.25 1.76,1.26 false 2.406,1.25 2.625,0.979 false 1.573,1.167 1.76,1.365 0.188,0.198 10 false *1 2.583,0.875 2.771,1.073 0.188,0.198 10 true *2

Text in Illustration
*1 Fixing Bolt A
*2 Adjusting Bolt B

a.

Install the fan and generator V belt.


b.

Turn the adjusting bolt B and adjust the tension of the V belt.


c.

Tighten the fixing bolt A.

Torque:

44 N*m (449 kgf*cm, 32 ft.*lbf)



d.

Tighten the adjusting B bolt.

Torque:

6.0 N*m (61 kgf*cm, 53 in.*lbf)



Hide 2.INSTALL NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT (w/ Air Conditioning System)

A146501E07
1.75,1.302 1.938,1.948 false 1.552,0.865 0.5,0.573 false 1.875,1.969 2.052,2.146 0.177,0.177 10 false *1 0.292,0.458 0.448,0.604 0.156,0.146 10 false *2

Text in Illustration
*1 Fixing Bolt A
*2 Adjusting Bolt B

a.

Install the No. 1 V belt.


b.

Turn the adjusting bolt B and adjust the tension of the V belt.


c.

Tighten the fixing bolt A.

Torque:

44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 16361A 3.INSPECT FAN AND GENERATOR V BELT

A103003

Text in Illustration
V100135

Measuring Point

a.

Check the fan and generator V belt deflection and tension.

HINT:

The specified deflection and tension values per belt are shown in the following table.


Standard Deflection (Pressing force: 98 N (10 kg, 22.0 lb)):
Item Specified Condition
New belt 10.5 to 12.5 mm (0.413 to 0.492 in.)
Used belt 12 to 13 mm (0.472 to 0.512 in.)


Standard Tension:
Item Specified Condition
New belt 350 to 500 N (36 to 51 kg, 79 to 112 lb)
Used belt 300 to 400 N (31 to 41 kg, 67 to 90 lb)


NOTICE:
·

Make sure not to tighten the fan and generator V belt higher than the specified tension. When the fan and generator V belt is overtightened, the lifespan of the fan and generator V belt is reduced.

·

If the fan and generator V belt deflection amount is 15 mm or more (tension 150 N (15 kg, 34 lb)), the fan and generator V belt may slip. Therefore, readjust the fan and generator V belt to the tension specified for "Used belt". (Frequent readjustment of the fan and generator V belt reduces the lifespan of the fan and generator V belt.)

·

Check that there are no cracks and damage on the fan and generator V belt. If there are any abnormalities, replace the part.



HINT:

The fan and generator V belt tension decreases after the vehicle has been driven, but since this occurs during the initial break-in period, this is not a malfunction.



Hide 4.INSPECT NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT (w/ Air Conditioning System)

A146591

Text in Illustration
V100135

Measuring Point

a.

Check the No. 1 V belt deflection and tension.

HINT:

The specified deflection and tension valves per belt are shown in the following table.


Standard Deflection (Pressing force: 98 N (10 kg, 22.0 lb)):
Item Specified Condition
New belt 8.6 to 10.6 mm (0.339 to 0.417 in.)
Used belt 10.7 to 12.1 mm (0.421 to 0.476 in.)


Standard Tension:
Item Specified Condition
New belt 404 to 576 N (41 to 59 kg, 91 to 129 lb)
Used belt 294 to 392 N (30 to 40 kg, 66 to 88 lb)


NOTICE:
·

Check the V belt deflection at the specified point.

·

When installing a new belt, set its tension to the specified value.

·

When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.




Hide 51441D 5.INSTALL NO. 1 ENGINE UNDER COVER (for Plastic Type)

Hide 51441D 6.INSTALL NO. 1 ENGINE UNDER COVER (for Metal Type)

Hide 51459 7.INSTALL ENGINE SIDE COVER STAY (for TCAP Made)