Home › Engine / Hybrid System › N04C-UH (ENGINE MECHANICAL) › CYLINDER HEAD
RM2850E _51 Engine / Hybrid System _073174 N04C-UH ENGINE MECHANICAL _0356076 CYLINDER HEAD A

N04C-UH ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11131 1.REMOVE INTAKE VALVE SEAT

A146573E05
0.989,0.364 1.164,0.525 0.176,0.162 10 *1 1.676,0.918 1.2,0.443 false 2.436,0.542 2.636,0.73 0.2,0.188 10 *2 2.047,1.681 2.383,0.625 false 2.587,1.588 2.775,1.77 0.188,0.182 10 *3 1.878,1.772 2.542,1.696 2.542,1.696 1.961,2.428 false 1.884,2.565 2.285,2.565 false 0.602,2.504 0.758,2.681 0.156,0.176 10 *a 1.408,1.938 0.815,2.564 0.815,2.564 1.477,2.455 false 2.338,2.466 2.518,2.636 0.18,0.17 10 *b

Text in Illustration
*1 Brass Block
*2 Valve Seat
*3 Valve
*a Electric Welding Applied
*b Grind these Points with Grinder

a.

Grind the 3 places on the circumference of a used valve and weld it to the valve seat as shown in the illustration.

NOTICE:

To protect the lower surface of the cylinder head from welding spatters, be sure to apply grease before welding.



b.

Place a brass block on the top of the valve stem and strike it with a hammer to remove the valve seat.

CAUTION:

When striking, the valve tips may break off on impact. Wear safety glasses to protect your eyes.



Hide 11135 2.REMOVE EXHAUST VALVE SEAT

A146573E05
0.989,0.364 1.164,0.525 0.176,0.162 10 *1 1.676,0.918 1.2,0.443 false 2.436,0.542 2.636,0.73 0.2,0.188 10 *2 2.047,1.681 2.383,0.625 false 2.587,1.588 2.775,1.77 0.188,0.182 10 *3 1.878,1.772 2.542,1.696 2.542,1.696 1.961,2.428 false 1.884,2.565 2.285,2.565 false 0.602,2.504 0.758,2.681 0.156,0.176 10 *a 1.408,1.938 0.815,2.564 0.815,2.564 1.477,2.455 false 2.338,2.466 2.518,2.636 0.18,0.17 10 *b

Text in Illustration
*1 Brass Block
*2 Valve Seat
*3 Valve
*a Electric Welding Applied
*b Grind these Points with Grinder

a.

Grind 3 places on the circumference of a used valve and weld it to the valve seat as shown in the illustration.

NOTICE:

To protect the lower surface of the cylinder head from welding spatters, be sure to apply grease before welding.



b.

Place a brass block on the top of the valve stem and strike it with a hammer to remove the valve seat.

CAUTION:

When striking, the valve tips may break off on impact. Wear safety glasses to protect your eyes.



Hide 11176 3.REMOVE INJECTION NOZZLE SEAT

a.
A146574E01
1.346,1.329 1.639,1.578 0.293,0.249 10 SST 1.047,1.173 1.309,1.407 false

Using SST, remove the injection nozzle seat.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


b.

Remove the O-ring from the cylinder head sub-assembly.


Hide 11122 4.REMOVE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


b.
A146575E01
2.208,0.996 1.905,0.517 false 1.536,0.435 1.829,0.705 0.294,0.269 10 SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01070)
09950-70010  (09951-07100)


Hide 11126 5.REMOVE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


b.
A146576E01
1.505,0.394 1.8,0.656 0.295,0.262 10 SST 2.289,0.918 1.868,0.497 false

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01070)
09950-70010  (09951-07100)


Hide 11122 6.INSTALL INTAKE VALVE GUIDE BUSH

a.
A146571

Using a caliper gauge, measure the inside diameter of the guide bush.

Bush Inside Diameter:

13.000 to 13.018 mm (0.5118 to 0.5125 in.)


HINT:

If the inside diameter of the cylinder head is greater than the maximum, replace the cylinder head.



b.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


c.
A146570E02
1.41,0.537 1.702,0.81 0.292,0.272 10 SST 2.191,1.032 1.791,0.623 false 0.624,1.744 0.81,1.932 0.185,0.188 10 *a

Using SST, tap in a new valve guide bush to the specified protrusion height.

Text in Illustration
*a Protrusion Height

SST
09201-10000  (09201-01070)
09950-70010  (09951-07100)

Protrusion Height:

26.4 to 26.8 mm (1.039 to 1.055 in.)


NOTICE:

Do not tap in the guide bush too much.



d.

Using a reamer, ream the inside of the valve guide bush to the specified oil clearance between the valve guide bush and valve stem.

Standard Oil Clearance:

0.014 to 0.029 mm (0.000551 to 0.00114 in.)



Hide 11126 7.INSTALL EXHAUST VALVE GUIDE BUSH

a.
A146571

Using a caliper gauge, measure the inside diameter of the guide bush.

Bush Inside Diameter:

13.000 to 13.018 mm (0.5118 to 0.5125 in.)


HINT:

If the inside diameter of the cylinder head is greater than the maximum, replace the cylinder head.



b.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


c.
A146572E02
1.531,0.406 1.82,0.667 0.289,0.261 10 SST 2.256,0.877 1.895,0.493 false 1.387,1.682 1.582,1.855 0.195,0.173 10 *a

Using SST, tap in a new valve guide bush to the specified protrusion height.

Text in Illustration
*a Protrusion Height

SST
09201-10000  (09201-01070)
09950-70010  (09951-07100)

Protrusion Height:

26.4 to 26.8 mm (1.039 to 1.055 in.)



d.

Using a reamer, ream the inside of the valve guide bush to the specified oil clearance between the valve guide bush and valve stem.

Standard oil clearance:

0.053 to 0.083 mm (0.00209 to 0.00327 in.)



Hide 11176 8.INSTALL INJECTION NOZZLE SEAT

a.
A146565E03
2.336,0.216 2.525,0.379 0.189,0.163 10 *1 2.058,0.8 2.305,0.327 false 1.349,1.382 0.815,1.328 false 1.4,1.712 0.959,1.666 false 0.566,1.229 0.754,1.393 0.189,0.163 10 *2 0.724,1.574 0.913,1.737 0.189,0.163 10 *3

Apply a light coat of engine oil to a new O-ring, and install it into the cylinder head.

Text in Illustration
*1 Cylinder Head
*2 O-ring
*3 Nozzle Seat

NOTICE:

Do not reuse the O-ring, as it may cause water or gas leakage inside the cylinder and the cylinder head may overheat or crack.



b.
A427411E01
1.063,2.667 1.583,2.781 false 0.885,2.573 1.198,2.771 0.313,0.198 10 false *1

Apply seal packing to a new nozzle seat.

Text in Illustration
*1 Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the installation surface of the cylinder head and nozzle seat.

·

Do not reuse the nozzle seat, as it may cause water or gas leakage inside the cylinder and the cylinder may overheat or crack.




c.
A146567E03
0.904,0.235 1.202,0.497 0.298,0.261 10 SST 1.058,1.302 1.229,1.455 0.171,0.154 10 *1 1.283,1.401 1.583,1.486 false 1.282,0.333 1.582,0.418 false

Using SST, install the nozzle seat into the cylinder head.

Text in Illustration
*1 Nozzle Seat

SST
09260-69015  (09268-06020)


d.
A146561E03
0.778,0.206 1.078,0.46 0.3,0.253 10 SST 1.128,1.61 1.312,1.794 0.184,0.184 10 *2 0.916,1.146 1.109,1.321 0.193,0.175 10 *1 1.58,1.501 1.15,1.255 false 1.693,1.869 1.359,1.717 false 1.582,0.544 1.152,0.298 false

Using SST, stake the nozzle seat.

Text in Illustration
*1 Nozzle Seat
*2 SST (Steel Ball)

SST
09260-69015  (09268-06010, 09268-06020)

NOTICE:

Put a container under the cylinder head to prevent the steel ball from being lost.



e.
A146611E03
2.597,1.447 2.84,1.654 0.243,0.206 10 *1

Install the injector into the cylinder head. Using a vernier caliper, measure the protrusion of the injection from the lower surface of the cylinder head.

Text in Illustration
*1 Protrusion

Standard Protrusion:

2.45 to 2.95 mm (0.0965 to 0.1161 in.)



Hide 11131 9.INSTALL INTAKE VALVE SEAT

a.
A146563E01
2.194,1.993 2.311,2.138 0.117,0.145 10 A 2.954,1.624 3.07,1.769 0.117,0.145 10 B

Using a caliper gauge and vernier caliper, measure the dimensions of the valve seat installation hole.

Cylinder Head Dimension:
A:

36.000 to 36.016 mm (1.4173 to 1.4179 in.)

B:

8.4 to 8.6 mm (0.3307 to 0.3386 in.)


If either result is not as specified, replace the cylinder head.


b.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


c.
A146564E01
0.071,0.378 0.358,0.648 0.288,0.27 10 SST 1.885,0.594 2.289,0.864 0.404,0.27 10 SST1 1.885,0.907 2.289,1.177 0.404,0.27 10 SST2 1.885,1.233 2.289,1.503 0.404,0.27 10 SST3 1.885,1.55 2.289,1.82 0.404,0.27 10 SST4 1.885,1.872 2.289,2.142 0.404,0.27 10 SST2 0.902,1.205 0.447,0.475 0.447,0.475 0.861,1.378 false 2.35,0.666 2.728,0.78 false 2.35,0.966 2.753,1.182 false 2.35,1.3 2.609,1.275 false 2.35,1.626 2.711,1.427 false 2.35,1.952 2.811,1.459 false

Using SST and a hammer, lightly tap the valve seat into the cylinder head.

SST
09950-70010  (09951-07100)

SST 1 09951-07100
SST 2 09952-06010
SST 3 09951-00360
SST 4 09951-00300


d.

Using SST and a hammer, completely tap in the valve seat.

SST
09950-70010  (09951-07100)


Hide 11135 10.INSTALL EXHAUST VALVE SEAT

a.
A146559E03
1.226,1.967 1.344,2.132 0.118,0.165 10 A 0.314,1.594 0.431,1.778 0.117,0.185 10 B

Using a caliper gauge and vernier caliper, measure the dimensions of the valve seat installation hole.

Cylinder Head Dimension:
A:

32.000 to 32.016 mm (1.2598 to 1.2605 in.)

B:

7.6 to 7.8 mm (0.2992 to 0.3071 in.)


If either result is not as specified, replace the cylinder head.


b.

Heat the cylinder head up to between 80 and 100°C (176 to 212 °F).


c.
A146560E01
0.074,0.466 0.383,0.699 0.309,0.233 10 SST 1.867,0.61 2.246,0.843 0.379,0.233 10 SST1 1.867,0.882 2.239,1.115 0.372,0.233 10 SST2 1.867,1.147 2.246,1.379 0.379,0.233 10 SST3 1.867,1.411 2.246,1.644 0.379,0.233 10 SST4 1.867,1.671 2.246,1.904 0.379,0.233 10 SST2 0.902,1.258 0.472,0.559 0.472,0.559 0.861,1.424 false 2.668,0.756 2.314,0.694 false 2.314,0.962 2.696,1.122 false 2.314,1.234 2.536,1.234 false 2.314,1.493 2.639,1.389 false 2.314,1.765 2.763,1.424 false

Using SST and a hammer, lightly tap the valve seat into the cylinder head.

SST
09950-70010  (09951-07100)

SST 1 09951-07100
SST 2 09952-06010
SST 3 09951-00360
SST 4 09951-00300


d.

Using SST and a hammer, completely tap in the valve seat.

SST
09950-70010  (09951-07100)