Home › Engine / Hybrid System › N04C-UH (LUBRICATION) › OIL AND OIL FILTER › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073179 N04C-UH LUBRICATION _0356103 OIL AND OIL FILTER A

N04C-UH LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will cause the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants that may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

·

For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 58521D 1.REMOVE ENGINE SERVICE HOLE COVER MAT (w/ Carpet)

Hide 58410 2.REMOVE ENGINE SERVICE HOLE COVER

Hide 58734B 3.REMOVE ENGINE SERVICE COVER WEATHERSTRIP REAR

Hide 58521D 4.REMOVE ENGINE SERVICE HOLE COVER MAT (w/o Carpet)

Hide 58420 5.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 53711C 6.REMOVE FRONT FENDER APRON RH

Hide 7.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the drain plug and gasket from the oil pan and drain the engine oil into a container.


c.

Clean the drain plug.


d.

Install the drain plug with a new gasket.

Torque:

41 N*m (418 kgf*cm, 30 ft.*lbf)



Hide 8.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A388375E02
1.208,1.052 1.604,1.052 false 0.906,0.99 1.24,1.177 0.333,0.188 10 true SST

Using SST, remove the oil filter sub-assembly.

SST
S0955-31030  


Hide 9.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Clean the oil filter sub-assembly installation surface.


b.

Apply engine oil to the oil filter gasket.


c.

Lightly screw the oil filter sub-assembly to the engine until the oil filter sub-assembly does not turn.

A388376E02
3.875,1.333 4.323,1.344 false 3.552,1.26 3.865,1.458 0.313,0.198 10 true SST


d.

Using SST, tighten the oil filter sub-assembly an additional 2/3 turn.

SST
S0955-31030  

Torque:

20 N*m (200 kgf*cm, 14 ft.*lbf)



Hide 10.ADD ENGINE OIL

a.

Add fresh oil and install the oil filler cap sub-assembly.

Engine oil:
Oil Grade Oil Viscosity (SAE)
·

API (CD, CE, CF, CH-4, CI-4, CJ-4)

·

JASO (DH-1, DH-2)

·

ACEA (E-3, E-4, E-5, E-6, E-9)


·

10W-30

·

20W-50

·

15W-40




Capacity:
Item Fill amount
Drain and refill with oil filter change 7.3 L (7.7 US qts, 6.4 Imp. qts)
Drain and refill without oil filter change 6.1 L (6.4 US qts, 5.4 Imp. qts)
Dry fill 8.0 L (8.5 US qts, 7.0 Imp. qts)



Hide 11.INSPECT FOR OIL LEAK

a.

Warm up the engine and check for engine oil leaks.


Hide 53711C 13.INSTALL FRONT FENDER APRON RH

Hide 58420 14.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58521D 15.INSTALL ENGINE SERVICE HOLE COVER MAT (w/o Carpet)

Hide 58734B 16.INSTALL ENGINE SERVICE COVER REAR WEATHERSTRIP

Hide 58410 17.INSTALL ENGINE SERVICE HOLE COVER

Hide 58521D 18.INSTALL ENGINE SERVICE HOLE COVER MAT (w/ Carpet)