Home › Engine / Hybrid System › N04C-UH (LUBRICATION) › OIL PUMP
RM2850E _51 Engine / Hybrid System _073179 N04C-UH LUBRICATION _0356106 OIL PUMP G

N04C-UH LUBRICATION  OIL PUMP  INSPECTION  


PROCEDURE

Hide 15100 1.INSPECT OIL PUMP ASSEMBLY

a.

Visually check each part of the oil pump for damage or wear.

If damage or wear is excessive, replace the oil pump assembly with a new one.


b.
A147521E04
2.427,0.719 2.156,0.188 false 0.729,1.146 0.469,0.615 false 1.469,1.375 1.208,1.896 false 1.948,0.063 2.125,0.26 0.177,0.198 10 true *2 0.24,0.49 0.417,0.635 0.177,0.146 10 false *1 1.094,1.917 1.281,2.115 0.188,0.198 10 true *3

Using a dial indicator, measure the backlash between the oil pump gear and No. 1 idle gear sub-assembly.

Standard Backlash:

0.065 to 0.215 mm (0.0026 to 0.0084 in.)


Maximum Backlash:

0.3 mm (0.0118 in.)


Text in Illustration

If the backlash is greater than the maximum, replace the oil pump assembly and No. 1 idle gear sub-assembly.

*1 Dial Indicator
*2 No. 1 Idle Gear Sub-assembly
*3 Oil Pump Gear


c.
A157026

Inspect the clearance between the oil pump driven gear and cylinder block.

i.

Using a vernier caliper, measure the length of the drive gear.

Standard Length:

27.02 to 27.04 mm (1.0638 to 1.0646 in.)



ii.
A157027

Using a vernier caliper, measure the depth of the cylinder block.

Standard Depth:

27.03 to 27.07 mm (1.0642 to 1.0658 in.)



iii.

Add the measurement of the cylinder block to the thickness of the gasket. From this total, subtract the measurement of the oil pump driven gear.

Standard Clearance:

0.05 to 0.13 mm (0.00197 to 0.00512 in.)


Maximum Clearance:

0.17 mm (0.00669 in.)


If the clearance is greater than the maximum, replace the oil pump assembly or cylinder block.



d.
A157028

Inspect the backlash between the drive gear and oil pump driven gear.

i.

Using a vise, fix the oil pump assembly.


ii.

Using a dial indicator, measure the backlash between the drive gear and oil pump driven gear.

Standard Backlash:

0.091 to 0.217 mm (0.00358 to 0.00854 in.)


Maximum Backlash:

0.25 mm (0.00984 in.)


If the backlash is greater than the maximum, replace the oil pump assembly with a new one.



e.
A157029

Inspect the clearance between the drive gear shaft and drive gear bush.

i.

Using a micrometer, measure the diameter of the drive gear shaft.

Standard Shaft Diameter:

18.088 to 18.106 mm (0.7121 to 0.7128 in.)


Minimum Shaft Diameter:

18.062 mm (0.7111 in.)



ii.
A157030

Using a dial indicator, measure the inside diameter of the drive gear bush.

Standard Bush Inside Diameter:

18.146 to 18.173 mm (0.7144 to 0.7155 in.)


Maximum Bush Inside Diameter:

18.20 mm (0.7165 in.)



iii.

Subtract the diameter measurement of the drive gear shaft from the inside diameter measurement of the drive gear bush.

Standard Clearance:

0.040 to 0.085 mm (0.00157 to 0.00335 in.)


Maximum Clearance:

0.10 mm (0.00394 in.)


If the clearance is greater than the maximum, replace the oil pump assembly or drive gear bush.



f.
A157031

Inspect the clearance between the driven gear shaft and driven gear bush.

i.

Using a micrometer, measure the diameter of the driven gear shaft.

Standard Shaft Diameter:

17.979 to 17.997 mm (0.7078 to 0.7085 in.)


Minimum Shaft Diameter:

17.97 mm (0.7075 in.)



ii.
A157032

Using a dial indicator, measure the inside diameter of the driven gear bush.

Standard Bush Inside Diameter:

18.037 to 18.054 mm (0.7101 to 0.7108 in.)


Maximum Bush Inside Diameter:

18.07 mm (0.7114 in.)



iii.

Subtract the diameter measurement of the driven gear shaft from the inside diameter measurement of the driven gear bush.

Standard Clearance:

0.040 to 0.075 mm (0.00157 to 0.00295 in.)


Maximum Clearance:

0.13 mm (0.00512 in.)


If the clearance is greater than the maximum, replace the driven gear or oil pump assembly.