Home › Drivetrain › M15# (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM2850E _52 Drivetrain _073186 M15# MANUAL TRANSMISSION / TRANSAXLE _0356140 OUTPUT SHAFT A

M15# MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 1.MEASURE THRUST CLEARANCE

a.
C395848

Measure the thrust clearance of each gear.

Standard clearance:
1st and 2nd gear:

0.10 to 0.35 mm (0.0039 to 0.0138 in.)

3rd gear:

0.10 to 0.60 mm (0.0039 to 0.0236 in.)

5th gear:

0.10 to 0.50 mm (0.0039 to 0.0197 in.)

Reverse gear:

0.15 to 0.40 mm (0.0059 to 0.0157 in.)


Maximum clearance:
1st and 2nd gear:

0.35 mm (0.0138 in.)

3rd gear:

0.60 mm (0.0236 in.)

5th gear:

0.50 mm (0.0197 in.)

Reverse gear:

0.40 mm (0.0157 in.)



Hide 2.MEASURE RADIAL CLEARANCE

a.
C395849

Using a dial indicator, measure the radial clearance for the following gears.

Standard clearance:
1st gear:

0.030 to 0.075 mm (0.0012 to 0.0030 in.)

2nd and Reverse gear:

0.030 to 0.081 mm (0.0012 to 0.0032 in.)

3rd and 5th gear:

0.015 to 0.066 mm (0.0006 to 0.0026 in.)


Maximum clearance:
1st gear:

0.075 mm (0.0030 in.)

2nd and Reverse gear:

0.081 mm (0.0032 In.)

3rd and 5th gear:

0.066 mm (0.0026 in.)


If the clearance is more than the limit, replace the gear. needle roller bearing and shaft.


Hide 33331 3.REMOVE REVERSE GEAR, REAR BEARING AND INNER RACE

a.
C395850

Using SST and a press, remove the reverse gear, rear bearing and inner race.

SST
09555-55010  


b.

Remove the ball and needle roller bearing.


Hide 33335 4.REMOVE 1ST GEAR AND NO. 1 HUB SLEEVE ASSEMBLY

a.
C395851

Using SST and a press, remove the 1st gear, synchronizer ring and No. 1 hub sleeve assembly.

SST
09555-55010  


b.

Remove the needle roller bearing.


Hide 33361 5.REMOVE NO. 1 HUB SLEEVE, SHIFTING KEYS AND SPRINGS FROM NO. 1 CLUTCH HUB

C395852

a.

Using a screwdriver, remove the 3 shifting keys and 2 springs from No. 1 clutch hub.


Hide 33336 6.REMOVE 5TH GEAR AND NO. 3 HUB SLEEVE ASSEMBLY

a.
C395853

Using 2 screwdrivers and a hammer, tap out the snap ring.


b.
C395854

Using SST, remove the No. 3 hub sleeve assembly.

SST
09950-50013  


c.

Remove the synchronizer ring.


d.
C395855

Remove the 5th gear, needle roller bearing and spacer.


Hide 33393 7.REMOVE NO. 3 HUB SLEEVE, SHIFTING KEYS AND SPRINGS FROM NO. 3 CLUTCH HUB

C395856

a.

Using a screwdriver, remove the 3 shifting keys and 2 springs from No. 3 clutch hub.


Hide 33333 8.REMOVE THRUST WASHER AND 3RD GEAR

a.
C395857

Using a snap ring expander, remove the snap ring.


b.
C395858

Remove the thrust washer and straight pin.


c.
C395859

Remove the 3rd gear, needle roller bearing and synchronizer rings.

NOTICE:
C395860

When dismantling the manual transmission, make sure the 3rd gear's inner, middle and outer synchronizer rings are tagged together with the spacer ring.



Hide 33332 9.REMOVE 2ND GEAR AND NO. 2 HUB SLEEVE ASSEMBLY

a.
C395861

Using 2 screwdrivers and a hammer, tap out the snap ring.


b.
C395862

Using a press, remove the 2nd gear, synchronizer rings and No. 2 hub sleeve assembly.

NOTICE:
C395863

When dismantling the manual transmission, make sure the 2nd gear's inner, middle and outer synchronizer rings are tagged together with the spacer ring.



c.

Remove the needle roller bearing.


Hide 33362 10.REMOVE NO. 2 HUB SLEEVE, SHIFTING KEYS AND SPRINGS FROM NO. 2 CLUTCH HUB

C395864

a.

Using a screwdriver, remove the 3 shifting keys and 2 springs from No. 2 clutch hub.