Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY
RM2850E _58 Vehicle Interior _073189 SEAT _0356165 FRONT SEAT ASSEMBLY L

SEAT  FRONT SEAT ASSEMBLY  PRECAUTION  


HINT:
·

The following procedures are used to prevent wrinkles from forming when installing the seat cover. Make sure to follow the procedures correctly.

·

The shape of the seat shown in the illustration may differ from the actual seat.



SEAT COVER SET


a.

Align the center cutout of the pad with the V-point of the cover.

B359745E01
4.688,1.781 4.688,1.531 true 4.969,1.01 4.688,1.313 true 6.646,0.729 5.979,0.729 true 6.646,2.104 5.979,2.104 true 4.625,1.813 4.833,2.021 0.208,0.208 10 true *a 5.01,0.917 5.219,1.125 0.208,0.208 10 true *b 6.688,0.635 6.896,0.844 0.208,0.208 10 true *2 6.708,2.01 6.917,2.219 0.208,0.208 10 true *1

Text in Illustration
*1 Pad *2 Cover
*a Center Cutout of Pad *b Cover V-point



INSTALL WIRE


a.

Install the wire to the cover as shown in the illustration.

HINT:

Make sure the wire is in the center of the cover.

B380442E01
1.75,0.552 2.063,0.75 0.313,0.198 10 false *a 5.354,0.583 5.667,0.781 0.313,0.198 10 false *b

Text in Illustration
*a Correct *b Incorrect




INSTALL HOG RING


a.
B359756

Using hog ring pliers, bend the hog rings into the shape shown in the illustration.

HINT:

Make sure to bend the hog rings into the proper shape. Wrinkles will form if improperly shaped hog rings are used.



b.

Install the hog rings in the order of the wires shown in the illustration.

HINT:
·
B359747E01
1.469,1.135 1.927,1.333 0.458,0.198 10 false (1) 1.792,1.813 2.25,2.01 0.458,0.198 10 false (2) 1.542,2.375 2,2.573 0.458,0.198 10 false (3) 1.063,1.146 1.521,1.344 0.458,0.198 10 false (4) 2.385,2.146 2.844,2.344 0.458,0.198 10 false (5) 1.99,0.781 2.448,0.979 0.458,0.198 10 false (6) 0.635,1.594 1.094,1.792 0.458,0.198 10 false *a 2.458,0.563 2.917,0.76 0.458,0.198 10 false *b

Install in the following order: Center of seatback, side closest to vehicle exterior, and then side closest to vehicle interior.

Text in Illustration
*a Vehicle Exterior
*b Vehicle Interior

·
B359748E01
2.229,1.646 2.688,1.844 0.458,0.198 10 false (1) 1.333,1.5 1.792,1.698 0.458,0.198 10 false (2) 0.906,1.854 1.365,2.052 0.458,0.198 10 false (3) 1.573,2.031 2.031,2.229 0.458,0.198 10 false (4) 2.052,1.219 2.51,1.417 0.458,0.198 10 false (5) 0.625,1.385 0.844,1.573 0.219,0.188 10 true (6) 0.542,2.333 0.76,2.521 0.219,0.188 10 false *a 2.49,0.604 2.708,0.792 0.219,0.188 10 false *b

Install in the following order:

Center of seat cushion, side closest to vehicle exterior, and then side closest to vehicle interior.

Text in Illustration
*a Vehicle Exterior
*b Vehicle Interior

·
B359749E02
1.302,0.292 1.542,0.531 false 0.917,1.427 1.26,1.177 true 1.698,1.854 1.698,1.521 true 1.125,0.198 1.438,0.354 0.313,0.156 10 false *a 0.771,1.406 0.948,1.563 0.177,0.156 10 true *b 1.625,1.875 1.938,2.031 0.313,0.156 10 false *c

Install the hog ring so that it is centered in the cutout of the pad.

Text in Illustration
*a Cover Hole
*b Pad Groove
*c Pad Cutout




c.
B359750

After installing the hog rings, hold the seam allowance on both ends of the cover and pull to match the pad and cover installation areas.

HINT:

If the cover is not matched to the pad, wrinkles will form.



d.

Push the cover seam allowance securely into the groove in the pad.

HINT:

Make sure to completely push the seam allowance into the groove. Wrinkles will form if any of the seam allowance is outside the groove.

B380443E01
1.396,0.5 1.906,0.677 false 4.802,0.333 5.198,0.333 true 4.552,1.167 5.469,1.167 true 0.865,1.167 1.781,1.167 true 1.24,0.385 1.552,0.542 0.313,0.156 10 false *a 0.698,1.094 1.01,1.25 0.313,0.156 10 false *b 0.729,0.073 1.042,0.229 0.313,0.156 10 false *c 4.146,0.104 4.458,0.26 0.313,0.156 10 false *d 4.625,0.25 4.938,0.406 0.313,0.156 10 false *a 4.375,1.094 4.688,1.25 0.313,0.156 10 false *b

Text in Illustration
*a Cover Seam Allowance *b Pad Groove
*c Correct *d Incorrect




CHECK COVER POSITION


a.

Fold the cover back as shown in the illustration and check that the cover V-points and the pad mark-off lines are approximately aligned.

B359752E01
0.854,1.854 0.469,1.563 0.469,1.563 0.802,1.26 true 1.031,1.854 1.323,1.5 1.323,1.5 0.969,1.25 true 0.969,2.927 0.438,2.677 0.438,2.677 1.052,2.521 true 1.198,2.906 1.521,2.698 1.521,2.698 1.177,2.51 true 5.927,2.917 5.635,2.677 5.635,2.677 5.958,2.51 true 6.167,2.917 6.771,2.729 6.771,2.729 6.083,2.531 true 6.094,1.865 5.781,1.521 5.781,1.521 6.156,1.26 true 6.271,1.844 6.74,1.594 6.74,1.594 6.344,1.271 true 1.375,1.427 1.688,1.583 0.313,0.156 10 false *a 0.292,1.49 0.604,1.646 0.313,0.156 10 false *b 0.271,2.594 0.583,2.75 0.313,0.156 10 false *b 1.563,2.625 1.875,2.781 0.313,0.156 10 false *a 5.615,1.448 5.927,1.604 0.313,0.156 10 false *a 5.479,2.594 5.792,2.75 0.313,0.156 10 false *a 6.792,1.521 7.104,1.677 0.313,0.156 10 false *b 6.813,2.646 7.125,2.802 0.313,0.156 10 false *b

Text in Illustration
*a Cover V-point *b Pad Mark-off Line



INSTALL COVER


a.

Align the cover of the seatback with the center of the seatback pad and the cover of the seat cushion with the center of the seat cushion pad. Afterward, install the covers starting from the vehicle exterior and working toward the vehicle interior.


b.

While removing wrinkles by hand as shown in the illustration, install the seatback cover by starting from the bottom and working toward the shoulders, and then install the seat cushion cover by starting from the front and working toward the rear.

B359764

HINT:
·

Do not push the pad into the cover. Instead, secure the pad and install the cover to the pad.

·

For Seatback Side:

When installing the cover to the outer side, install the cover up until the installation area of the outer side headrest support.

·

Do not apply an excessive amount of force when covering the corners, as doing so may cause the cover to tear or fray.




c.

Align the cover seam line with the edges of the pad.

B371020

HINT:
·

Double-stitch type:

B380444E01
6.031,0.667 5.844,0.365 false 5.75,0.531 5.333,0.531 false 5.823,1 5.24,1 true 3.667,1 2.833,1 true 3.01,1.156 2.823,1.323 false 4.073,0.333 3.885,0.5 false 3.313,0.719 3.083,0.583 false 6.75,0.771 6.875,1 false 4.552,0.844 4.135,0.844 false 0.896,0.938 0.406,1.135 false 0.979,1.083 0.427,1.135 false 2.927,0.438 3.24,0.594 0.313,0.156 10 false *a 5.073,0.906 5.385,1.063 0.313,0.156 10 false *c 6.833,1.031 7.063,1.281 0.229,0.25 10 false *d 2.333,0.125 2.646,0.281 0.313,0.156 10 false *e 4.927,0.135 5.24,0.292 0.313,0.156 10 false *f 5.698,0.229 6.01,0.385 0.313,0.156 10 false *a 5.177,0.458 5.49,0.615 0.313,0.156 10 false *b 2.677,0.896 2.99,1.052 0.313,0.156 10 false *c 2.688,1.313 3,1.469 0.313,0.156 10 false *b 4.073,0.24 4.385,0.396 0.313,0.156 10 false *b 4.573,0.76 4.802,1.01 0.229,0.25 10 false *d 0.24,1.083 0.552,1.24 0.313,0.156 10 false *b

Text in Illustration
*a Cover Seam Line *b Cover Seam (Stitch)
*c Pad Edge *d Felt
*e Correct *f Incorrect

·

Single-stitch type:

Align the seam allowance in a single direction.

B380445E01
2.792,1.031 2.677,0.667 false 5.427,0.99 5.01,0.99 false 5.427,1.219 4.844,1.219 true 6.188,0.948 5.604,0.948 true 3.417,0.667 2.99,1.063 true 2.604,1.208 2.354,1.208 true 2.01,3.26 1.583,3.656 true 5.25,3.188 4.823,3.583 true 6.188,0.865 6.5,1.021 0.313,0.156 10 false *b 4.667,1.146 4.979,1.302 0.313,0.156 10 false *c 1.427,3.646 1.74,3.802 0.313,0.156 10 false *d 0.646,2.604 0.958,2.76 0.313,0.156 10 false *e 3.927,2.604 4.24,2.76 0.313,0.156 10 false *f 2.563,0.49 2.875,0.646 0.313,0.156 10 false *a 4.844,0.906 5.156,1.063 0.313,0.156 10 false *a 3.438,0.51 3.75,0.667 0.313,0.156 10 false *c 2.188,1.135 2.5,1.292 0.313,0.156 10 false *b 4.635,3.563 4.948,3.719 0.313,0.156 10 false *d

Text in Illustration
*a Cover Seam Line *b Cover Seam (Stitch)
*c Pad Edge *d Seam Allowance of Cover
*e Correct *f Incorrect




d.

Push the cover seam allowance securely into the groove in the pad.

HINT:

Make sure to completely push the seam allowance into the groove. Wrinkles will form if any of the seam allowance is outside the groove.

B380446E01
1.021,0.063 1.333,0.219 0.313,0.156 10 false *a 4.542,0.063 4.854,0.219 0.313,0.156 10 false *b

Text in Illustration
*a Correct *b Incorrect




REMOVE WRINKLES


a.

After installing the cover with pad to the seat frame, use your fingers to trace the seam line of each part and remove wrinkles.

NOTICE:

If there are wrinkles in the webbing, wrinkles will appear on the surface of the cover.

B359762




CHECKS TO PERFORM AFTER WORK IS FINISHED


a.

Smooth the cover as shown in the illustration and make sure that there are no wrinkles.

HINT:
·

If wrinkles remain, it is very likely that the hog rings were not properly bent or covering was not properly performed.

·

If the cover appears to be off to one side, it is very likely that the hog ring positions are incorrect.

·

If waves form in the seam line, it is very likely that the seam allowance is not in the groove or the position of the felt is incorrect.

B359763