Home › General › INTRODUCTION › HOW TO USE THIS MANUAL
RM2850E _V1 General _073193 INTRODUCTION _0356192 HOW TO USE THIS MANUAL F

INTRODUCTION  HOW TO USE THIS MANUAL  GENERAL INFORMATION  


GENERAL DESCRIPTION


a.

Repair operations can be separated mainly into the following 3 processes:

i.

Diagnosis


ii.

Removing / Installing, Replacing, Disassembling / Reassembling, Checking and Adjusting


iii.

Final Inspection



b.

The following procedures are omitted from this manual. However, these procedures must be performed.

i.

Use a jack or lift to perform operations


ii.

Clean all removed parts


iii.

Perform a visual check




INDEX


a.

An alphabetical INDEX section is provided at the end of the manual as a reference to help you find the item to be repaired.



PREPARATION


a.

Use of Special Service Tools (SST) and Special Service Materials (SSM) may be required, depending on the repair procedure. Be sure to use SST and SSM when they are required and follow the working procedure properly. A list of SST and SSM is in the "Preparation" section of this manual.



REPAIR PROCEDURES


a.

A component illustration is placed under the title where necessary.


b.

Non-reusable parts, grease application areas, precoated parts and torque specifications are noted in the component illustrations.

The following illustration is an example.

D225270E01
0.156,2.146 0.844,2.344 0.688,0.198 2.979,1.563 3.635,1.75 0.656,0.188 0.083,3.073 1.375,3.292 1.292,0.219 1.479,0.229 1.823,0.229 false 0.698,1.5 0.938,1.344 false 1.469,0.958 1.802,0.719 1.802,0.719 2.021,0.719 false 1.76,1.865 2.156,1.208 2.156,1.208 2.375,1.208 false 0.771,0.604 1.073,0.604 false 0.896,2.635 1.146,2.635 false 3.094,2.844 3.292,2.844 3.292,2.844 3.51,2.104 false 4.115,2.281 4.177,1.906 false 5.344,2.771 5.094,2.771 5.094,2.771 4.896,1.802 false 5.646,2.385 5.427,2.385 5.427,2.385 5.198,1.74 false 6.146,2.083 5.948,2.083 5.948,2.083 5.813,1.5 false 6.438,1.677 6.198,1.677 6.198,1.677 6.125,1.448 false 6.49,1.292 6.302,0.823 6.302,0.823 6.49,0.823 false 5.688,1.104 5.427,0.427 5.427,0.427 5.615,0.427 false 5.344,1.375 4.396,0.594 4.396,0.594 4.583,0.594 false 4.552,1.656 3.917,0.99 3.917,0.99 4.104,0.99 false 0.844,2.24 1.021,2.24 1.021,2.24 1.177,2.031 false 2.75,1.667 2.979,1.667 false 0.073,0.031 1.323,0.323 1.25,0.292 10 false Example: 1.885,0.156 3.135,0.448 1.25,0.292 10 false Filter Cap 0.365,0.51 1.615,0.802 1.25,0.292 10 false Float 2.125,0.656 3.906,1.063 1.781,0.406 10 false Reservoir Tank 0.052,1.521 1.833,1.927 1.781,0.406 10 false Slotted Spring Pin 2.615,1.125 4.396,1.531 1.781,0.406 10 false Grommet 0.292,2.542 2.073,2.948 1.781,0.406 10 false Cylinder 2.604,2.75 4.385,3.156 1.781,0.406 10 false Piston 3.771,2.302 5.552,2.708 1.781,0.406 10 false Push Rod 5.448,2.688 6.729,3 1.281,0.313 10 false Snap Ring 5.74,2.302 6.969,2.594 1.229,0.292 10 false Boot 6.208,2 7.094,2.292 0.885,0.292 10 false Lock Nut 6.479,1.604 7.135,1.833 0.656,0.229 10 false Clevis 6.552,0.76 7.125,0.969 0.573,0.208 10 false Clip 5.698,0.354 6.948,0.625 1.25,0.271 10 false Clevis Pin 4.823,0.51 6.073,0.781 1.25,0.271 10 false Gasket 4.198,0.906 5.448,1.177 1.25,0.271 10 false Washer 2.448,1.115 2.927,1.333 0.479,0.219 10 false ● 4.656,0.5 5.135,0.719 0.479,0.219 10 false ● 0.167,3.438 0.646,3.656 0.479,0.219 10 false ● 0.333,3.448 2.104,3.708 1.771,0.26 10 false Non-reusable part 0.146,3.083 1.917,3.344 1.771,0.26 10 false N*m (kgf*cm, ft.*lbf) 1.417,3.094 3.188,3.354 1.771,0.26 10 false : Specified torque 0.208,2.167 1.99,2.573 1.781,0.406 8 false 15 (155,11) 3.042,1.583 4.823,1.99 1.781,0.406 8 false 12 (120,9)


c.

Torque specifications, grease application areas and non-reusable parts are emphasized in the procedures.

HINT:

There are cases where such information can only be explained by using an illustration. In these cases, torque, oil and other information are described in the illustration.



d.

Only items with key points are described in the text. What to do and other details are explained using illustrations next to the text. Both the text and illustrations are accompanied by standard values and notices.

Illustration What to do and where to do it
Task heading What work will be performed
Explanation text How to perform the task
Also has information such as specifications and warnings, which arewritten in boldface text


e.

Illustrations of similar vehicle models are sometimes used. In these cases, minor details may be different from the actual vehicle.


f.

Procedures are presented in a step-by-step format.



SERVICE SPECIFICATIONS


a.

SPECIFICATIONS are presented in boldface text throughout the manual. The specifications are also found in the "Service Specifications" section for reference.



TERM DEFINITIONS


CAUTION Possibility of injury to you or other people.
NOTICE Possibility of damage to components being repaired.
HINT Provides additional information to help you perform repairs.


INTERNATIONAL SYSTEM OF UNITS


a.

The units used in this manual comply with the International System of Units (SI UNIT) standard. Units from the metric system and the English systems are also provided.

Example:

Torque:

30 N*m (310 kgf*cm, 22 ft.*lbf)