Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0356197 STEERING PAD N

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

HINT:

When scrapping a vehicle equipped with an SRS or disposing of the horn button assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs during the airbag deployment, contact the Service Dept. of the distributor.


CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a horn button assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the horn button assembly.

·

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



Hide 2.DISPOSE OF HORN BUTTON ASSEMBLY (WHEN SCRAPPING VEHICLE DEPLOYMENT METHOD)

NOTICE:
·

When disposing of the horn button assembly, use an unneeded vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E68
0.958,1.198 0.958,0.698 0.958,0.698 0.646,0.698 true 0.302,0.615 0.76,0.813 0.458,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS Airbag Deployment Tool


i.
C110372E37
0.844,1.615 0.844,1.146 0.844,1.146 0.479,1.146 true 2.521,0.771 2.865,0.771 true 0.177,1.083 0.635,1.281 0.458,0.198 10 false SST 2.917,0.698 3.24,0.906 0.323,0.208 10 false *a

Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

Text in Illustration
*a Battery


ii.
C110475E32
0.885,0.344 1.667,0.344 1.667,0.344 1.667,0.677 false 0.563,0.26 1.021,0.458 0.458,0.198 10 false SST

Check the function of SST.

Press SST activation switch and check that the LED of SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.




c.

Remove the lower steering column cover.

Click hereVehicle Interior>WIPER / WASHER>WIPER SWITCH>REMOVAL


d.

Remove the upper steering column cover.

Click hereVehicle Interior>WIPER / WASHER>WIPER SWITCH>REMOVAL


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



f.

Disconnect the airbag connector from the spiral cable sub-assembly.

i.
B464673E01
1.104,2.906 0.604,2.49 true 1.156,2.896 1.469,3.094 0.313,0.198 10 false *a

Slide the slider to release the lock, and then disconnect the airbag connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.


Text in Illustration
*a Slider
V100135

Slide in this Direction



g.

Install SST.

i.
B471050E01
2.771,1.052 2.771,0.813 true 1.823,1.052 2.365,0.823 2.365,0.823 2.906,0.823 true 2.552,1.063 2.552,0.823 true 2.938,0.75 3.396,0.948 0.458,0.198 10 false SST

Connect the SST connector to the airbag connector of the spiral cable sub-assembly.

SST
09082-00700  09082-00760  

CAUTION:

Check that there is no looseness in the steering wheel and horn button assembly.


NOTICE:

To avoid damaging SST connector and the wire harness, do not lock the secondary lock of the twin lock.



ii.
B340835E03
1.313,0.896 1.313,0.385 1.313,0.385 1.688,0.385 true 0.677,1.542 0.677,1.313 0.677,1.313 0.417,1.313 true 0.115,1.229 0.573,1.427 0.458,0.198 10 false SST 1.719,0.302 2,0.51 0.281,0.208 10 false *a 1.708,1.885 2,2.094 0.292,0.208 10 false *b

Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

Text in Illustration
*a Battery
*b 10 m or more


iii.

While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



h.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press SST activation switch to deploy the airbag.

CAUTION:
·

Before deployment, make sure that no one is near the vehicle.

·

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




Hide 3.DISPOSE OF HORN BUTTON ASSEMBLY (WHEN DISPOSING OF AIRBAG ASSEMBLY DEPLOYMENT METHOD)

NOTICE:

Be sure to follow the procedure detailed below when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E69
0.938,1.208 0.938,0.74 0.938,0.74 0.698,0.74 true 0.365,0.667 0.823,0.865 0.458,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS Airbag Deployment Tool


i.
C110372E38
2.521,0.75 2.75,0.75 true 0.521,0.729 0.833,0.729 0.833,0.729 0.833,1.625 true 0.229,0.635 0.688,0.833 0.458,0.198 10 false SST 2.792,0.677 3.063,0.885 0.271,0.208 10 false *a

Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

Text in Illustration
*a Battery


ii.
C110475E33
0.75,0.344 1.677,0.344 1.677,0.344 1.677,0.667 true 0.427,0.26 0.885,0.458 0.458,0.198 10 false SST

Check the function of SST.

Press SST activation switch and check that the LED of SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.




c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



d.

Remove the horn button assembly (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL).

CAUTION:
·

Before removing the horn button assembly, wait at least 90 seconds after turning the engine switch off and disconnecting the cable from the negative (-) battery terminal.

·

When storing the horn button assembly, keep the airbag deployment side facing upward.




e.
B515005E01
1.958,1.594 1.958,1.24 true 2.646,0.521 2.958,0.719 0.313,0.198 10 false *a 1.896,1.594 2.208,1.792 0.313,0.198 10 false *b

Using braided wire, tie down the horn button assembly to an unneeded tire and wheel set.

Text in Illustration
*a Wire Harness Diameter
*b Stripped Wire Harness Section

Cross-sectional area of stripped wire harness section:

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the horn button assembly, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire section:

Area = 3.14 x (Diameter)2 / 4


i.
B451203E01
2.719,2.083 2.885,2.083 true 2.438,2.969 2.708,2.073 2.708,2.073 2.719,2.969 true 2.927,2.01 3.333,2.208 0.406,0.198 10 false SST

After connecting the following SST to each other ,connect them to the horn button assembly.

SST
09082-00802  (09082-10801, 09082-20801)


ii.

Push in the lock button to lock the SST connector.


iii.
B451196E01
0.833,1.656 1.083,1.073 true 1.865,1.635 2.115,1.052 true 0.698,1.635 1.01,1.833 0.313,0.198 10 false *a 1.771,1.635 2.083,1.833 0.313,0.198 10 false *a

Wind 3 wire harnesses at least 2 times each around each of the pins.

Text in Illustration
*a 2 times or more

CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the horn button assembly may break loose when the airbag is deployed.

·

Always tie down the horn button assembly with the airbag deployment side facing upward.




iv.
B451197E01
1.854,0.542 2.156,0.219 true 2.188,0.125 2.5,0.323 0.313,0.198 10 false *a

Face the airbag deployment side of the horn button assembly upward on top of an unneeded tire and wheel set. Separately tie the left and right sides of the horn button assembly to the wheel through the hub nut holes. Position SST connector so that it hangs downward through the hub hole of the wheel.

Text in Illustration
*a Deployment Side

CAUTION:
·

Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the horn button assembly may break loose when the airbag is deployed.

·

Always tie down the horn button assembly with the airbag deployment side facing upward.



NOTICE:

The tire and wheel may be damaged by the airbag deployment, so use an unneeded tire and wheel.




f.
B451198E01
3.292,0.865 2.854,0.469 true 2.51,0.354 2.969,0.552 0.458,0.198 10 false SST

Install SST.

CAUTION:

Place the tire and wheel set on level ground.


i.

Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging SST connector and the wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the disc wheel.



ii.
B284468E02
1.219,1.99 1.5,1.99 true 1.552,1.906 2.01,2.104 0.458,0.198 10 false SST 1.375,2.854 1.667,3.052 0.292,0.198 10 false *a

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire and wheel set.

Text in Illustration
*a 10 m or more



g.

Cover the horn button assembly (using a cardboard box).

i.
B284469E02
2.021,2.854 2.021,2.354 true 2.583,2.844 1.385,2.844 1.385,2.844 1.385,2.354 true 1.125,0.625 1.281,0.823 0.156,0.198 10 false Y 0.896,1.281 1.052,1.479 0.156,0.198 10 false Y 2.948,1.458 3.104,1.656 0.156,0.198 10 false X 2.635,2.76 2.885,2.969 0.25,0.208 10 false *a

Cover the horn button assembly with a cardboard box.

Text in Illustration
*a Weight


ii.

Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).

Minimum Cardboard box size:

Must exceed the following dimensions

X:

460 mm (1.51 ft.)

Y:

650 mm (2.13 ft.)


NOTICE:
·

When dimension Y of the cardboard box exceeds the diameter of the tire with disc wheel which the horn button assembly is tied to, X should be the following size.

X = 460 mm (1.51 ft.) + width of tire

·

If a cardboard box which is smaller than the specified size is used, the cardboard box will be damaged by the shock from the airbag deployment.





h.

Cover the horn button assembly (using tires).

i.
B452370E01
1.677,0.281 1.99,0.479 0.313,0.198 10 false *b 2.823,0.719 3.135,0.917 0.313,0.198 10 false *c 0.625,1.677 0.938,1.875 0.313,0.198 10 false *a

Place at least 3 tires without wheels onto the wheel and tire to which the horn button assembly is tied.

Text in Illustration
*a Tire (3 or more)
*b Inner Diameter
*c Width


ii.

Place a wheel and tire on top.

Minimum Tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:

Do not use tires with disc wheels except on the top and bottom.


NOTICE:
·

As the tires may be damaged by the airbag deployment, use tires that you are planning to throw away.

·

Do not place SST connector under the tire because it could be damaged.




iii.
B105087

Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.




i.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

B515933E01
1.375,0.802 1.375,0.583 1.375,0.583 1.615,0.583 true 4.823,0.823 4.823,0.604 4.823,0.604 5.063,0.604 true 0.667,0.25 0.979,0.448 0.313,0.198 10 false *A 4.156,0.25 4.469,0.448 0.313,0.198 10 false *B 1.604,2.281 1.917,2.479 0.313,0.198 10 false *a 5.021,2.26 5.333,2.458 0.313,0.198 10 false *a 1.667,0.5 1.979,0.698 0.313,0.198 10 false SST 5.104,0.531 5.417,0.729 0.313,0.198 10 false SST

Text in Illustration
*A Using Cardboard Box *B Using Tires
*a 10 m or more - -


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the horn button assembly is tied.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:

When deploying the airbag, make sure that no one is near the tire.


HINT:

The airbag is deployed as the LED of SST activation switch comes on.




j.

Dispose of the horn button assembly.

CAUTION:
·

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the horn button assembly from the disc wheel.


ii.

Place the horn button assembly in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.