Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0356199 FRONT PASSENGER AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for 2 Connectors Type:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>PRECAUTION

for 3 Connectors Type:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55433B 3.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 88650N 4.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 73970A 5.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B468044E01
0.708,2.427 0.51,2.125 true 0.958,2.448 0.958,2.146 0.958,2.146 1.125,2.146 true 0.344,2.021 0.656,2.219 0.313,0.198 10 false *a 1.156,2.083 1.406,2.281 0.25,0.198 10 false *b

Remove the 2 bolts.


d.

Disconnect the airbag connector.

i.

Slide the slider to release the lock, and then disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


Text in Illustration
*a Slider
*b Slide in this Direction



e.
B471845

Using the moulding remover B to detach the 12 claws.


f.

Remove the instrument panel passenger airbag assembly.


Hide 82142 6.REMOVE NO. 2 INSTRUMENT PANEL WIRE

a.
B468045E01
0.917,2.448 1.135,2.135 1.135,2.135 1.396,2.135 true 0.833,2.781 1.042,2.979 1.042,2.979 1.292,2.979 true 1.438,2.073 1.75,2.271 0.313,0.198 10 false *a 1.344,2.896 1.656,3.094 0.313,0.198 10 false *b

Using a screwdriver, release the airbag connector lock button and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Lock Button
*b Protective Tape


b.

Detach the wire harness clamp to remove the No. 2 instrument panel wire.