Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG ECU
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0356201 AIRBAG ECU A

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG ECU  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for 2 Connectors Type:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>PRECAUTION

for 3 Connectors Type:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here


Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

Hide 51774C 3.REMOVE STEP PLATE COVER

a.

for Type A, Type B:

Remove the 4 bolts and step plate cover.


b.

for Type C:

Remove the 3 bolts and step plate cover.

B468053E01
0.271,0.073 0.583,0.271 0.313,0.198 10 false *A 3.969,0.073 4.281,0.271 0.313,0.198 10 false *B 1.99,2.333 2.302,2.531 0.313,0.198 10 false *C

Text in Illustration
*A for Type A *B for Type B
*C for Type C - -


Hide 51771J 4.REMOVE STEP

a.

Remove the 4 bolts and step.

B468054E01
0.198,0.073 0.51,0.271 0.313,0.198 10 false *A 3.906,0.094 4.219,0.292 0.313,0.198 10 false *B

Text in Illustration
*A for LHD *B for RHD


Hide 89170A 5.REMOVE AIRBAG ECU ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B464701E01
1,0.792 1.604,1.115 true 1.667,3.188 1.885,2.26 1.885,2.26 2.646,2.26 true 1.635,1.031 1.948,1.229 0.313,0.198 10 false *a 0.875,0.344 1.188,0.542 0.313,0.198 10 false *c 0.823,1.083 1.021,1.281 0.198,0.198 10 true *d 2.698,2.198 2.99,2.396 0.292,0.198 10 false *b

Disconnect the airbag connector.

Text in Illustration
*a Connector Lock Lever
*b Waterproof Sheet
*c Push
*d Release in this Direction

NOTICE:
·

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

·

Do not remove the waterproof sheet.



i.

Push the connector lock lever to release the connector lock as shown in the illustration.


ii.

Disconnect the airbag connector.



d.

Remove the 3 bolts and airbag ECU assembly.

NOTICE:

If the airbag ECU assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the airbag ECU assembly with a new one.