Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS(for LH Side)
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356204 BACK DOOR GLASS(for LH Side) A

WINDOW / GLASS  BACK DOOR GLASS(for LH Side)  INSTALLATION  


PROCEDURE

Hide 68131D 1.CLEAN BACK DOOR GLASS LH

a.
E268586

Clean the outer edge of the back door glass LH with non-residue solvent.

NOTICE:
·

Do not touch the back door glass LH surface after cleaning it.

·

Do not damage the glass.

·

Even if using a new back door glass LH, clean the back door glass with non-residue solvent.




Hide 64827A 2.INSTALL BACK WINDOW GLASS CLIP RH

a.

Using non-residue solvent, clean the back window glass clip RH surface of the back door glass LH.


b.

Install the glass primer to the back window glass clip RH installation surface of the back door glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass clip RH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 2 back window glass clips RH to the back door glass LH as shown in the illustration.

B473271E01
0.573,1.063 0.323,1.229 0.323,1.229 0.563,0.833 true 0.771,1.063 1.073,1.208 1.073,1.208 0.76,0.833 true 0.792,1.917 1.052,2.198 1.052,2.198 0.781,1.688 true 0.552,1.927 0.302,2.104 0.302,2.104 0.542,1.677 true 4.115,1.073 3.865,1.24 3.865,1.24 4.104,0.844 true 4.323,1.073 4.625,1.219 4.625,1.219 4.313,0.844 true 4.094,1.917 3.844,2.083 3.844,2.083 4.094,1.698 true 4.333,1.927 4.573,2.135 4.573,2.135 4.323,1.677 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.156,1.208 0.385,1.385 0.229,0.177 10 false *b 1.042,1.219 1.271,1.396 0.229,0.177 10 false *b 0.146,2.135 0.375,2.313 0.229,0.177 10 false *b 1.031,2.198 1.26,2.375 0.229,0.177 10 false *b 0.948,0.125 1.26,0.323 0.313,0.198 12 false *A 4.469,0.146 4.781,0.344 0.313,0.198 12 false *B 3.719,1.208 3.948,1.385 0.229,0.177 10 false *b 4.625,1.219 4.854,1.396 0.229,0.177 10 false *b 3.708,2.083 3.938,2.26 0.229,0.177 10 false *b 4.531,2.177 4.76,2.354 0.229,0.177 10 false *b

Text in Illustration
*A w/o Outer Under Rear View Mirror *B w/ Outer Under Rear View Mirror
*a Back Side *b Ceramic Notch


Hide 64828 3.INSTALL BACK WINDOW GLASS CLIP LH

a.

Using non-residue solvent, clean the back window glass clip LH surface of the back door glass LH.


b.

Install the glass primer to the back window glass clip LH installation surface of the back door glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass clip LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 2 back window glass clips LH to the back door glass LH as shown in the illustration.

B473270E01
2.917,0.813 3.385,0.552 3.385,0.552 3.063,0.813 true 2.906,1.083 3.354,1.385 3.354,1.385 3.052,1.083 true 2.885,1.667 3.427,1.552 3.427,1.552 3.073,1.677 true 2.865,1.948 3.281,2.271 3.281,2.271 3.063,1.958 true 6.438,0.792 6.25,0.521 6.25,0.521 6.625,0.802 true 6.438,1.063 6.281,1.313 6.281,1.313 6.604,1.063 true 6.427,1.667 6.865,1.385 6.865,1.385 6.594,1.667 true 6.417,1.958 6.281,2.26 6.281,2.26 6.594,1.948 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 3.427,0.479 3.74,0.677 0.313,0.198 10 false *b 3.406,1.313 3.719,1.51 0.313,0.198 10 false *b 3.469,1.5 3.781,1.698 0.313,0.198 10 false *b 3.344,2.229 3.656,2.427 0.313,0.198 10 false *b 0.448,0.198 0.76,0.396 0.313,0.198 12 false *A 3.917,0.208 4.229,0.406 0.313,0.198 12 false *B 6.073,0.375 6.271,0.552 0.198,0.177 10 false *b 6.083,1.26 6.281,1.438 0.198,0.177 10 false *b 6.917,1.281 7.115,1.458 0.198,0.177 10 false *b 6.146,2.26 6.344,2.438 0.198,0.177 10 false *b

Text in Illustration
*A w/o Outer Under Rear View Mirror *B w/ Outer Under Rear View Mirror
*a Back Side *b Ceramic Notch


Hide 68294A 4.INSTALL BACK DOOR GLASS ADHESIVE DAM

a.

Using non-residue solvent, clean the back door glass adhesive dam surface of the back door glass LH.


b.

Install the glass primer to the back door glass adhesive dam installation surface of the back door glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back door glass adhesive dam.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

w/o Outer Under Rear View Mirror:

i.

Install the 4 back door glass adhesive dams to the back door glass LH as shown in the illustration.

B473272E01
1.5,0.469 1.771,0.719 1.771,0.719 1.719,0.469 true 2.531,1.115 2.635,1.271 2.635,1.271 2.75,1.104 true 2.635,2.01 2.771,1.927 2.771,1.927 2.625,1.813 true 1.49,3.156 1.396,3.365 1.396,3.365 1.719,3.156 true 5.573,3.177 5.479,3.385 5.479,3.385 5.802,3.177 true 6.677,2 6.813,1.917 6.813,1.917 6.677,1.802 true 5.552,0.479 5.844,0.667 5.844,0.667 5.792,0.479 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.427,0.229 0.74,0.427 0.313,0.198 12 false *A 4.219,0.24 4.531,0.438 0.313,0.198 12 false *B 1.313,0.167 1.469,0.323 0.156,0.156 10 true A 1.313,0.844 1.448,0.99 0.135,0.146 10 true A 1.813,2.833 1.969,2.99 0.156,0.156 10 true A 1.833,3.573 1.99,3.729 0.156,0.156 10 true A 5.906,3.573 6.063,3.729 0.156,0.156 10 true A 5.885,2.865 6.042,3.021 0.156,0.156 10 true A 5.365,0.135 5.521,0.292 0.156,0.156 10 true A 5.365,0.875 5.51,1.031 0.146,0.156 10 true A 1.813,0.656 2.031,0.833 0.219,0.177 10 false *b 2.531,1.281 2.75,1.458 0.219,0.177 10 false *b 2.781,1.823 3,2 0.219,0.177 10 false *b 1.219,3.344 1.438,3.521 0.219,0.177 10 false *b 3.542,2.875 3.719,3.052 0.177,0.177 10 false a 5.292,3.323 5.51,3.5 0.219,0.177 10 false *b 6.875,1.833 7.094,2.01 0.219,0.177 10 false *b 5.896,0.656 6.115,0.833 0.219,0.177 10 false *b

Text in Illustration
*A w/o Outer Under Rear View Mirror *B w/ Outer Under Rear View Mirror
*a Back Side *b Ceramic Notch

Standard:
Area Specified Condition
a 19.0 mm (0.748 in.)




e.

w/ Outer Under Rear View Mirror:

i.

Install the 3 back door glass adhesive dams to the back door glass LH as shown in the illustration.



Hide 64813B 5.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using non-residue solvent, clean the back window glass adhesive dam surface of the back door glass LH.


b.

Install the glass primer to the back window glass adhesive dam installation surface of the back door glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass adhesive dam.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the back window glass adhesive dam to the back door glass LH as shown in the illustration.

B473274E01
0.333,2.844 0.573,3.177 true 3.99,2.833 4.229,3.167 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.125,0.177 1.438,0.375 0.313,0.198 12 false *A 4.792,0.177 5.104,0.375 0.313,0.198 12 false *B 0.24,0.594 0.396,0.792 0.156,0.198 10 false a 1.104,1.438 1.26,1.615 0.156,0.177 10 false A 1.469,1.438 1.625,1.615 0.156,0.177 10 false A 0.594,3.188 0.906,3.385 0.313,0.198 10 false *b 3.26,2.802 3.417,3 0.156,0.198 10 false b 2.646,2.802 2.99,2.958 0.344,0.156 10 false A-A 4.24,3.188 4.552,3.385 0.313,0.198 10 false *b 3.906,0.615 4.063,0.813 0.156,0.198 10 false a 4.771,1.469 4.927,1.646 0.156,0.177 10 false A 5.135,1.469 5.292,1.646 0.156,0.177 10 false A

Text in Illustration
*A w/o Outer Under Rear View Mirror *B w/ Outer Under Rear View Mirror
*a Back Side *b Ceramic Notch

Standard:
Area Specified Condition
a 14.5 mm (0.571 in.)
b 4.5 mm (0.177 in.)



Hide 75574B 6.INSTALL BACK WINDOW OUTSIDE MOULDING LH

a.

Using non-residue solvent, clean the back window outside moulding LH surface of the back door glass LH.


b.

Install the glass primer to the back window outside moulding LH installation surface of the back door glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window outside moulding LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the back window outside moulding LH to the back door glass LH as shown in the illustration.

B473273E01
3.135,2.365 3.344,2.542 true 6.813,2.375 6.979,2.542 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.438,0.177 0.75,0.375 0.313,0.198 12 false *A 3.865,0.177 4.177,0.375 0.313,0.198 12 false *B 1.969,1.302 2.125,1.5 0.156,0.198 10 false A 2.333,1.292 2.49,1.49 0.156,0.198 10 false A 3.177,0.865 3.333,1.063 0.156,0.198 10 false a 3.365,2.844 3.521,3.042 0.156,0.198 10 false c 2.865,2.76 3.219,2.938 0.354,0.177 10 false A-A 3.385,2.5 3.698,2.698 0.313,0.198 10 false *b 6.917,2.573 7.146,2.76 0.229,0.188 10 false *b 6.844,0.854 7,1.052 0.156,0.198 10 false b 5.625,1.313 5.781,1.51 0.156,0.198 10 false A 5.99,1.313 6.146,1.51 0.156,0.198 10 false A

Text in Illustration
*A w/o Outer Under Rear View Mirror *B w/ Outer Under Rear View Mirror
*a Back Side *b R End

Standard:
Area Specified Condition
a 14.5 mm (0.571 in.)
b 10.4 mm (0.571 in.)
c 11.2 mm (0.441 in.)



Hide 68131D 7.INSTALL BACK DOOR GLASS LH

a.

Clean and shape the contact surface of the door panel.

i.
B455055E01
0.583,1.177 0.583,1.448 false 0.5,1.479 0.813,1.677 0.313,0.198 10 false *a 3.115,0.375 3.26,0.552 0.146,0.177 10 false a

On the contact surface of the door panel, use a knife to cut away excess adhesive as shown in the illustration.

Standard:
Area Specified Condition
a 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.)



ii.

Clean the contact surface of the door panel with non-residue solvent.

Text in Illustration
*a Door Panel
V100155

Adhesive



b.

Position the back door glass LH.

i.

Using suction cups, place the back door glass LH in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Using suction cups, remove the back door glass LH.


iv.

Using a brush or sponge, apply body primer to the exposed part of the door panel.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




v.

Using a brush or sponge, apply glass primer to the contact surface of the glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B473275E01
0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.542,0.135 0.854,0.333 0.313,0.198 12 false *A 0.563,2.406 0.875,2.604 0.313,0.198 12 false *B 2.25,0.031 2.406,0.198 0.156,0.167 10 false A 2.25,0.385 2.406,0.552 0.156,0.167 10 false A 2.25,2.417 2.406,2.583 0.156,0.167 10 false A 2.25,2.781 2.406,2.948 0.156,0.167 10 false A 0.833,0.823 0.99,0.99 0.156,0.167 10 false B 1.188,0.823 1.344,0.99 0.156,0.167 10 false B 1.208,3.198 1.365,3.365 0.156,0.167 10 false B 0.823,3.208 0.979,3.375 0.156,0.167 10 false B 2.354,1.875 2.51,2.042 0.156,0.167 10 false C 2.354,2.26 2.51,2.427 0.156,0.167 10 false C 2.354,4.281 2.51,4.448 0.156,0.167 10 false C 2.365,4.625 2.521,4.792 0.156,0.167 10 false C 2.76,0.823 2.917,0.99 0.156,0.167 10 false D 3.156,0.823 3.313,0.99 0.156,0.167 10 false D 2.76,3.229 2.917,3.396 0.156,0.167 10 false D 3.156,3.229 3.313,3.396 0.156,0.167 10 false D 3.708,0.792 4.094,0.958 0.385,0.167 10 false A-A 5.406,0.781 5.792,0.948 0.385,0.167 10 false B-B 3.698,2.552 4.083,2.719 0.385,0.167 10 false C-C 5.417,2.563 5.802,2.729 0.385,0.167 10 false D-D 4.417,0.917 4.573,1.115 0.156,0.198 10 false a 4.24,2.698 4.396,2.896 0.156,0.198 10 false a 4.115,1.281 4.271,1.479 0.156,0.198 10 false b 4.563,3.073 4.719,3.229 0.156,0.156 10 false b 6.094,1.167 6.25,1.365 0.156,0.198 10 false c 5.917,2.823 6.073,3.021 0.156,0.198 10 false d

Text in Illustration
*A w/o Outer Under Rear View Mirror *B w/ Outer Under Rear View Mirror
*a Back Side *b R End
V100155

Glass Primer Application Area - -

Standard:
Area Specified Condition
a 14.0 mm (0.551 in.)
b 6.0 mm (0.236 in.)
c 14.8 mm (0.583 in.)
d 21.0 mm (0.827 in.)




c.

Apply adhesive to the back door glass LH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



d.
B214800E33
2.49,0.583 2.958,0.406 true 1.292,1.427 1.563,1.646 0.271,0.219 10 false a 3,0.292 3.25,0.552 0.25,0.26 10 false *1 0.583,0.625 0.833,0.865 0.25,0.24 10 false a 1.115,0.906 1.427,1.135 0.313,0.229 10 false b 0.76,1.021 0.958,1.229 0.198,0.208 10 false b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


Text in Illustration
*1 Sealer Gun

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.



e.

Load the sealer gun with the cartridge.


f.

Apply adhesive to the glass as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B473276E01
4.448,1.813 4.646,2.052 true 6.229,1.802 6.427,2.042 true 4.302,3.573 4.5,3.813 true 5.771,3.625 6.188,3.823 6.188,3.823 6.01,3.604 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.531,0.115 0.844,0.313 0.313,0.198 12 false *A 0.563,2.375 0.875,2.573 0.313,0.198 12 false *B 2.271,0.042 2.448,0.188 0.177,0.146 10 false A 2.26,0.375 2.438,0.521 0.177,0.146 10 false A 2.26,2.427 2.438,2.573 0.177,0.146 10 false A 2.26,2.792 2.438,2.938 0.177,0.146 10 false A 0.833,0.833 1.01,0.979 0.177,0.146 10 false B 1.198,0.833 1.375,0.979 0.177,0.146 10 false B 0.833,3.219 1.01,3.365 0.177,0.146 10 false B 1.198,3.219 1.375,3.365 0.177,0.146 10 false B 2.344,1.896 2.521,2.042 0.177,0.146 10 false C 2.344,2.25 2.521,2.396 0.177,0.146 10 false C 2.365,4.302 2.542,4.448 0.177,0.146 10 false C 2.365,4.625 2.542,4.771 0.177,0.146 10 false C 2.771,0.813 2.948,0.958 0.177,0.146 10 false D 3.135,0.813 3.313,0.958 0.177,0.146 10 false D 2.771,3.208 2.948,3.354 0.177,0.146 10 false D 3.156,3.219 3.333,3.365 0.177,0.146 10 false D 3.708,0.781 4.073,0.979 0.365,0.198 10 false A-A 3.729,2.563 4.094,2.76 0.365,0.198 10 false C-C 5.427,2.542 5.792,2.74 0.365,0.198 10 false B-B 5.438,0.781 5.802,0.979 0.365,0.198 10 false D-D 4.219,1.115 4.396,1.26 0.177,0.146 10 false a 4.448,2.698 4.625,2.844 0.177,0.146 10 false a 6.094,1.052 6.271,1.198 0.177,0.146 10 false b 4.688,2.021 4.938,2.198 0.25,0.177 10 false *b 6.448,2.01 6.698,2.188 0.25,0.177 10 false *b 4.552,3.792 4.802,3.969 0.25,0.177 10 false *b 6.229,3.781 6.479,3.958 0.25,0.177 10 false *b 6.063,2.667 6.25,2.854 0.188,0.188 10 false c 5.854,3.021 6.031,3.167 0.177,0.146 10 false d 5.646,3.01 5.823,3.156 0.177,0.146 10 false e

Text in Illustration
*A w/o Outer Under Rear View Mirror *B w/ Outer Under Rear View Mirror
*a Back Side *b Adhesive Center
V100155

Adhesive - -

Standard:
Area Specified Condition
a 13.0 mm (0.512 in.)
b 7.8 mm (0.307 in.)
c 6.0 mm (0.236 in.)
d 8.0 mm (0.315 in.)
e 4.0 mm (0.157 in.)



g.

Install the back door glass LH to the door panel.


h.

Using suction cups, attach the 2 back window glass clips LH and 2 back window glass clips RH and install the back door glass LH.

B473264E02
0.51,0.146 0.885,0.385 0.375,0.24 12 false *A 3.635,0.115 4.01,0.354 0.375,0.24 12 false *B

Text in Illustration
*A w/o Outer Under Rear View Mirror *B w/ Outer Under Rear View Mirror


i.

Press it in gently along the rim.

NOTICE:
·

Check that the back window glass clips LH and back window glass clips RH are attached to the door panel correctly.

·

Check that the door panel and glass have a small gap between them.



HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



j.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive to the glass rim.



Hide 8.INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 67754 9.INSTALL BACK DOOR TRIM MOULDING

a.
B471619E01
1.656,0.417 1.875,0.292 1.875,0.292 2.844,0.292 true 2.906,0.219 3.219,0.417 0.313,0.198 10 true *a

Align the installation mark on the back door trim moulding to the cutout of the door panel and install it.

Text in Illustration
*a Installation Mark (Paint)


Hide 62384P 10.INSTALL SIDE WINDOW CLIP CAP

a.
B471618

Install the side window clip cap.


Hide 87950 11.INSTALL OUTER UNDER REAR VIEW MIRROR ASSEMBLY (w/ Outer Under Rear View Mirror)

Hide 68129B 12.INSTALL EMERGENCY BACK DOOR WINDSHIELD GLASS (for Emergency Door)

a.
B473277E01
1.083,2.229 1.448,2.406 0.365,0.177 10 false A-A 2.344,0.771 2.5,0.927 0.156,0.156 10 false A 1.885,0.781 2.042,0.938 0.156,0.156 10 true A

Install the emergency back door windshield glass to the outer back door window emergency glass weatherstrip.


Hide 64562 13.INSTALL OUTER BACK DOOR WINDOW EMERGENCY GLASS WEATHERSTRIP (for Emergency Door)

a.
B473278E01
1.115,2.271 1.448,2.438 0.333,0.167 10 false A-A 2.354,0.771 2.51,0.948 0.156,0.177 10 false A 1.896,0.781 2.052,0.958 0.156,0.177 10 true A

Install the outer back door window emergency glass weatherstrip to the door panel.


Hide 64563 14.INSTALL INNER BACK DOOR WINDOW EMERGENCY GLASS WEATHERSTRIP (for Emergency Door)

a.
B473279E01
1,2.26 1.354,2.448 0.354,0.188 10 false A-A 2.344,0.792 2.5,0.948 0.156,0.156 10 false A 1.885,0.792 2.042,0.948 0.156,0.156 10 true A

Install the inner back door window emergency glass weatherstrip to the outer back door window emergency glass weatherstrip.