Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
1.CLEAN FRONT SIDE WINDOW GLASS LH
Clean the outer edge of the front side front window glass LH with non-residue solvent.
Do not touch the front side window glass LH surface after cleaning it.
Do not damage the glass.
Even if using a new front side window glass LH, clean the front side window glass LH with non-residue solvent.
62269F
2.INSTALL SIDE WINDOW FRAME FILM
Perform the following procedures when replacing the side window frame film.
Remove the double-sided tape remaining on the installation surface of the side window frame film of the front side window glass assembly LH.
Using non-residue solvent, clean the installation surface of the side window frame film of the front side window glass assembly LH.
Remove the peeling paper on a new side window frame film while making sure not to touch the adhesional surface.
Install the 9 pieces of side window frame film at the positions shown in the illustration.
| *a | Specified Application Position | *b | Align the lateral center of the front window frame film RH with the center of the hole in the front side window glass assembly LH. |
| *c | Back side | - | - |
|
Tape | - | - |
| Area | Specified Condition |
|---|---|
| a | 4.6 mm (0.181 in.) |
68142D
3.INSTALL SIDE FRONT WINDOW RUN LH
Perform the following procedures when replacing the side front window run LH.
Remove the adhesive remaining on the installation surface of the side front window run LH of the front side window glass assembly LH.
Using non-residue solvent, clean the installation surface of the side front window run LH of the front side window glass assembly LH.
Apply adhesive to the installation surface of the side front window run LH of the front side window glass assembly LH.
Make sure that the adhesive does not contact any other areas outside of the application area.
Clean any protruding adhesive.
Apply adhesive to the entire circumference.
| *a | Back Side |
Install a new side front window run LH to the front side window glass assembly LH.
62910L
4.INSTALL SIDE WINDOW LOCK ASSEMBLY
Use the same procedure for each of the side window lock assemblies.
Install the side window lock packing.
If there is extreme damage to the side window lock packing, replace it with a new one.
Install the side window lock retainer.
Install the side window lock assembly with 2 screws.
Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.
Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the side window lock packing.
Apply adhesive to the threaded portion of the screw.
Install the side window lock assembly with 2 screws.
62746G
5.INSTALL QUARTER WINDOW PACKING
Perform the following procedures when replacing the quarter window packing.
Clean any adhesive from the installation surface of the quarter window packing on the front side window center frame sub-assembly LH.
Using non-residue solvent, clean the installation surface of the quarter window packing of the front side window center frame sub-assembly LH.
Install a new quarter window packing to the front side window center frame sub-assembly LH and keep it in the position shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 3.0 mm (0.118 in.) |
Apply instant adhesive to the fitting surface (dotted line) on the quarter window packing and front side window center frame sub-assembly LH to secure the quarter window packing.
Make sure that instant adhesive does not contact any other areas outside of the application area.
Prepare an EPT sealer with the dimensions shown in the illustration.
A generic EPT sealer can be used.
| *a | Seal Area |
| Area | Specified Condition |
|---|---|
| a | 5.0 mm (0.197 in.) |
| b | 4.0 mm (0.157 in.) |
| c | 30 mm (1.18 in.) |
Remove the peeling paper and install the EPT sealer to the side window center frame sub-assembly at the position shown in the illustration.
| *a | Application Reference Line | *b | Specified Application Position |
| *c | View A | - | - |
62777U
6.INSTALL SIDE WINDOW CENTER SASH CAP
Perform the following procedures when replacing the side window center sash cap.
Install a new side window center sash cap to the front side window glass assembly LH at the position shown in the illustration.
| *a | Vehicle Front |
62211F
7.INSTALL REAR SIDE WINDOW GLASS LH
Do not damage the front side front window glass LH.
Do not damage the window frame.
Do not damage the rear side window glass LH.
Widen top and bottom of the window frame using your hands and install the rear side window glass LH.
Install the center side window frame sub-assembly.
Install the screw:
Before applying adhesive, clean off any old adhesive from the threaded portion.
Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the front side front window glass LH.
Apply adhesive to the threaded portion.
Install the 2 screws.
62121
8.INSTALL FRONT SIDE FRONT WINDOW GLASS LH
Do not damage the front side front window glass LH.
Do not damage the window frame.
Do not damage the front side front window glass LH.
Widen top and bottom of the window frame using your hands and install the front side front window glass LH.
Install the screw:
Before applying adhesive, clean off any old adhesive from the threaded portion.
Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the front side front window glass LH.
Apply adhesive to the threaded portion.
Install the 2 screws.
Apply sealant (water proof) to the head of the screw in the area shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 3.0 mm (0.118 in.) |
| b | 12.2 mm (0.480 in.) |
62391B
9.INSTALL NO. 1 FRONT SIDE WINDOW STOPPER LH
Install the No. 1 front side window stopper LH.
Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.
Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the No. 1 front side window stopper LH.
Apply adhesive to the threaded portion of the screw.
Install a new No. 1 front side window stopper LH with the 2 screws.
62763N
10.INSTALL SIDE WINDOW FRAME RETAINER
Using non-residue solvent, clean the side window frame retainer installation surface of the front side window glass LH.
Install the primer to the side window frame retainer installation surface of the front side window glass LH.
Using non-residue solvent, clean the windshield glass retainer installation surface of the windshield glass.
Install the glass primer to the windshield glass retainer installation surface of the windshield glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new side window frame retainer.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 3 side window frame retainers to the front side window glass LH as shown in the illustration.
| *1 | Side Window Frame Retainer | - | - |
| *a | Back Side | - | - |
| Area | Specified Condition |
|---|---|
| a | 383.5 mm (15.1 in.) |
| b | 533.4 mm (21.0 in.) |
| c | 683.1 mm (26.9 in.) |
62375B
11.INSTALL NO. 1 SIDE WINDOW CLIP
Using non-residue solvent, clean the No. 1 side window clip installation surface of the front side window glass LH.
Remove the peeling paper from a new No. 1 side window clip.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 3 No. 1 side window clips to the front side window glass LH as shown in the illustration.
Install the primer to the No. 1 side window clip installation surface of the front side window glass LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | Long Clip |
| *c | Short Clip | *d | Ceramic Notch |
| Area | Specified Condition |
|---|---|
| a | 117.1 mm (4.61 in.) |