Home › Vehicle Exterior › WINDOW / GLASS › FRONT DOOR GLASS SUB-ASSEMBLY RH
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356211 FRONT DOOR GLASS SUB-ASSEMBLY RH A

WINDOW / GLASS  FRONT DOOR GLASS SUB-ASSEMBLY RH  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 1.INSTALL FRONT DOOR WINDOW PACKING

NOTICE:

Perform the following procedures when replacing the front door window packing.


a.

Using non-residue solvent, clean the front door window packing installation surface of the front door glass sub-assembly RH.


b.

Remove the peeling paper from a new front door window packing.


c.

Install the front door window packing shown in the illustration.

HINT:

Install so that the hole in the front door window assembly RH is in the center of the front window packing.


B471200E01
1.563,2.354 1.802,2.531 1.802,2.531 1.969,2.531 true 3.896,2.354 4.135,2.531 4.135,2.531 4.302,2.531 true 5.24,0.833 5.385,0.833 5.385,0.833 5.552,0.938 false 5.948,0.958 6.302,0.958 false 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 0.667,1.385 0.833,1.552 0.167,0.167 10 false A 0.667,1.75 0.833,1.917 0.167,0.167 10 false A 3.021,1.385 3.188,1.552 0.167,0.167 10 false A 3.021,1.802 3.188,1.969 0.167,0.167 10 false A 1.396,2.063 1.563,2.229 0.167,0.167 10 false a 1.615,2.063 1.781,2.229 0.167,0.167 10 false a 1.479,1.969 1.646,2.135 0.167,0.167 10 false *c 3.75,2.063 3.917,2.229 0.167,0.167 10 false a 3.948,2.063 4.115,2.229 0.167,0.167 10 false a 3.802,1.969 3.969,2.135 0.167,0.167 10 false *c 2.042,2.448 2.25,2.615 0.208,0.167 10 false *b 4.344,2.458 4.552,2.625 0.208,0.167 10 false *b 5.052,0.771 5.26,0.938 0.208,0.167 10 false *b 4.823,0.417 5.156,0.594 0.333,0.177 10 false A-A 6.375,0.885 6.594,1.052 0.219,0.167 10 false *1

Text in Illustration
*1 Front Door Window Packing - -
*a Back side *b Hole
*c Center of Front Window Packing - -

Standard:
Area Specified Condition
a 25.0 mm (0.984 in.)



Hide 62269E 2.INSTALL FRONT WINDOW FRAME FILM RH

NOTICE:

Perform the following procedures when replacing the front window frame film RH.


HINT:

Remove the adhesive remaining on the installation surface of the front window frame film RH of the front door window assembly RH.


a.

Using non-residue solvent, clean the installation surface of the front window frame film RH of the front door window assembly RH.


b.

Remove the peeling paper on a new piece of front window frame film RH while making sure not to touch the adhesional surface.


c.
B507063E01
2.063,2.573 2.063,2.188 2.063,2.188 1.99,2.188 true 0.323,2.573 0.323,2.188 0.323,2.188 0.25,2.188 true 0.073,2.115 0.302,2.292 0.229,0.177 10 false *a 1.792,2.104 2.021,2.281 0.229,0.177 10 false *a 0.635,3.052 0.844,3.219 0.208,0.167 10 true *b 2.354,3.052 2.563,3.219 0.208,0.167 10 true *b 1.427,2.573 1.563,2.76 0.135,0.188 10 false a 3.146,2.573 3.281,2.76 0.135,0.188 10 false a 0.125,0.115 0.427,0.354 0.302,0.24 10 false *c

Install the 5 pieces of front window frame film RH to the positions shown in the illustration.

Text in Illustration
*a Specified Application Position
*b Align the lateral center of the front window frame film RH with the center of the hole in the front door window assembly RH.
*c Back side
V100155

Tape

Standard:
Area Specified Condition
a 4.5 mm (0.177 in.)



Hide 62411K 3.INSTALL FRONT DOOR WINDOW RUN RH

NOTICE:

Perform the following procedures when replacing the front door window run RH.


HINT:

Clean any adhesive from the installation surface of the front door window run RH on the front door window assembly RH.


a.

Using non-residue solvent, clean the front door window run RH installation surface of the front door window assembly RH.


b.
B471140

Install the adhesive to the front door window run RH installation surface of the front door window assembly RH.

NOTICE:
·

Make sure that adhesive does not contact any other areas outside of the application area.

·

Remove any excess or protruding adhesive.

·

Apply adhesive to the entire circumference.




c.

Install a new front door window run RH to the front door window assembly RH.


Hide 62746G 4.INSTALL QUARTER WINDOW PACKING

NOTICE:

Perform the following procedures when replacing the quarter window packing.


HINT:

Clean any adhesive from the installation surface of the quarter window packing on the front door window center frame sub-assembly RH.


a.

Using non-residue solvent, clean the installation surface of the quarter window packing of the front door window center frame sub-assembly RH.


b.
B471150E02
2.323,0.792 2.635,0.99 0.313,0.198 10 false *a

Install a new quarter window packing to the front door window center frame sub-assembly RH and keep it in the position shown in the illustration.

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)



c.
B471198

Apply instant adhesive to the fitting surface (dotted line) on the quarter window packing and front door window center frame sub-assembly RH to secure the quarter window packing.

NOTICE:

Make sure that the adhesive does not contact any other areas outside of the application area.



d.
B505393E01
2.51,0.313 2.75,0.115 2.75,0.115 2.885,0.115 true 1.344,0.385 1.5,0.583 0.156,0.198 10 false c 0.396,1.302 0.552,1.5 0.156,0.198 10 false a 0.875,1.906 1.031,2.104 0.156,0.198 10 false b 2.958,0.052 3.198,0.229 0.24,0.177 10 false *a

Prepare an EPT sealer with the dimensions shown in the illustration.

HINT:

A generic EPT sealer can be used.


Text in Illustration
V100155

Tape

Standard:
Area Specified Condition
a 5.0 mm (0.197 in.)
b 4.0 mm (0.157 in.)
c 30 mm (1.18 in.)



e.

Remove the peeling paper and install the EPT sealer to the front door window center frame sub-assembly RH at the position shown in the illustration.

B505394E01
1.865,1.208 2.302,0.635 2.302,0.635 2.458,0.635 false 3.26,2.208 4.281,2.208 false 2.51,0.552 2.823,0.75 0.313,0.198 10 false *b 3.042,2.135 3.302,2.323 0.26,0.188 10 false *a 2.74,1.813 2.927,2 0.188,0.188 10 false A 6.688,2.104 6.948,2.292 0.26,0.188 10 false *a 5.781,0.792 6.042,0.979 0.26,0.188 10 false *c

Text in Illustration
*a Application Reference Line *b Specified Application Position b
*c View A - -


Hide 62910L 5.INSTALL SIDE WINDOW LOCK ASSEMBLY

HINT:

Use the same procedure for each of the side window lock assemblies.


a.
B471136

Install the side window lock packing.

NOTICE:

If there is extreme damage to the side window lock packing, replace it with a new one.



b.
B471137

Install the side window lock retainer.


c.
B471135

Install the side window lock assembly with 2 screws.

i.

Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the side window lock packing.


iii.

Apply adhesive to the threaded portion of the screw.


iv.

Install the side window lock assembly with the 2 screws.



Hide 62777U 6.INSTALL FRONT DOOR WINDOW CENTER SASH CAP RH

NOTICE:

Perform the following procedures when replacing the front door window center sash cap RH.


a.
B471151E01
2.885,1.615 3.198,1.813 0.313,0.198 10 false *a

Install the front door center window sash cap RH to the front door window assembly RH shown in the illustration.

Text in Illustration
*a Front


Hide 62317 7.INSTALL FRONT DOOR REAR WINDOW GLASS RH

NOTICE:
·

Do not damage the front door window glass assembly RH.

·

Do not damage the front door out window frame sub-assembly.

·

Do not damage the front door rear window glass RH.



a.
B471147

Widen top and bottom of the window frame using your hands and install the front door rear window glass RH.


Hide 62039 8.INSTALL FRONT DOOR CENTER WINDOW FRAME SUB-ASSEMBLY RH

a.
B471146

Install the front door center window frame sub-assembly RH.


b.

Install the screw:

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the front door glass sub-assembly RH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.



Hide 62315D 9.INSTALL FRONT DOOR FRONT WINDOW GLASS RH

NOTICE:
·

Do not damage the front door window glass assembly RH.

·

Do not damage the front door out window frame sub-assembly.

·

Do not damage the front door front window glass RH.



a.
B471145

Widen top and bottom of the window frame using your hands and install the front door front window glass RH.


b.
B471132

Install the screw:

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the front door glass sub-assembly RH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.


v.
B471199E01
1.229,0.208 1.385,0.406 0.156,0.198 10 false a 2.031,0.208 2.188,0.406 0.156,0.198 10 false a 2.906,1.031 3.063,1.229 0.156,0.198 10 false b

Apply sealant (water proof) to the head of the screw in the area shown in the illustration.

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)
b 12.2 mm (0.480 in.)




Hide 67120D 10.INSTALL FRONT DOOR WINDOW STOPPER

NOTICE:

Perform the following procedures when replacing the front door window stopper.


a.
B471197

Install the front door window stopper.

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the front door glass sub-assembly RH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.



Hide 62385A 11.INSTALL FRONT DOOR NO. 1 WINDOW SEAL

NOTICE:

Perform the following procedures when replacing the front door No. 1 window seal.


HINT:

Clean any adhesive from the installation surface of the front door No. 1 window seal on the front door rear window glass RH.


a.

Using non-residue solvent, clean the front door No. 1 window seal installation surface of the front door rear window glass RH.


b.

Install a new front door No. 1 window seal to the front door window glass assembly RH shown in the illustration.

B507052E01
3.635,0.417 3.375,0.177 3.375,0.177 3.208,0.177 true 3.531,0.667 3.281,0.844 3.281,0.844 3.115,0.844 true 3.563,2.438 3.427,2.438 3.427,2.438 3.313,2.26 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.844,0.146 1.156,0.302 0.313,0.156 10 false A-A 0.823,1.51 1.135,1.667 0.313,0.156 10 false B-B 1.188,0.146 1.656,0.313 0.469,0.167 10 false (1)-(2) 1.198,1.51 1.667,1.677 0.469,0.167 10 false (2)-(3) 3.427,0.292 3.583,0.49 0.156,0.198 10 false A 3.781,0.438 3.938,0.635 0.156,0.198 10 false A 4.167,1.01 4.323,1.208 0.156,0.198 10 false B 4.542,1.083 4.698,1.281 0.156,0.198 10 false B 3,0.104 3.24,0.313 0.24,0.208 10 false (1) 2.927,0.781 3.167,0.99 0.24,0.208 10 false (2) 3.625,2.365 3.865,2.573 0.24,0.208 10 false (3)

Text in Illustration
*a Back side *b R End
V100155

Adhesive Application Area - -

Standard:
Area Specified Condition
a 102.0 mm (4.02 in.)


NOTICE:
·

Make sure that instant adhesive does not contact any other areas outside of the application area.

·

Make sure that adhesive does not contact the design surface of the front door window assembly RH.

·

Remove any excess or protruding adhesive.




Hide 62385C 12.INSTALL NO. 1 SIDE WINDOW SEAL

NOTICE:

Perform the following procedures when replacing the No. 1 side window seal.


HINT:

Remove the adhesive remaining on the installation surface of the No. 1 side window seal of the front door window assembly RH.


a.

Using non-residue solvent, clean the installation surface of the No. 1 side window seal of the front door window assembly RH.


b.

Install a new No. 1 side window seal to the front door window glass assembly RH shown in the illustration.

NOTICE:
·

Make sure that instant adhesive does not contact any other areas outside of the application area.

·

Make sure that adhesive does not contact the design surface of the front door window assembly RH.

·

Clean any protruding adhesive.



B505428E01
2.833,2.51 2.99,2.51 2.99,2.51 3.25,2.333 true 4.219,2.573 4.063,2.573 4.063,2.573 3.708,2.344 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 0.781,0.844 1.094,1.042 0.313,0.198 10 false A-A 4.948,1.875 5.104,2.052 0.156,0.177 10 false A 4.948,2.26 5.104,2.438 0.156,0.177 10 false A 3.458,2.552 3.615,2.729 0.156,0.177 10 false a 2.625,2.438 2.844,2.625 0.219,0.188 10 false *1 4.271,2.5 4.49,2.688 0.219,0.188 10 false *2

Text in Illustration
*1 No. 1 Front Door Window Seal *2 No. 1 Side Window Seal
*a Back side - -
V100155

Adhesive Application Area - -

Standard:
Area Specified Condition
a 10 to 15 mm (0.394 to 0.591 in.)