68113C
1.CLEAN GLIDE DOOR GLASS
When reusing the glide door glass:
Using a gasket scraper, remove any remaining, pin, moulding, adhesive dam, double-sided tape and adhesive residue from the glide door glass.
Be careful not to damage the glide door glass.
Clean the outer circumference of the glide door glass with non-residue solvent.
Do not touch the glide door glass surface after cleaning it.
Even if using a new glide door glass, clean the glide door glass with non-residue solvent.
68217G
2.INSTALL CENTER DOOR NO. 2 FIX WINDOW PIN
Using non-residue solvent, clean the center door No. 2 fix window pin installation surface of the glide door glass.
Using a brush or sponge, coat the glass primer to the center door No. 2 fix window pin installation surface of the glide door glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new center door No. 2 fix window pin.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 2 center door No. 2 fix window pins to the glide door glass as shown in the illustration.
| *a | Back Side | *b | Ceramic Notch |
68217F
3.INSTALL CENTER DOOR NO. 1 FIX WINDOW PIN
Using non-residue solvent, clean the center door No. 1 fix window pin installation surface of the glide door glass.
Using a brush or sponge, coat the glass primer to the center door No. 1 fix window pin installation surface of the glide door glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new center door No. 1 fix window pin.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 2 center door No. 1 fix window pins to the glide door glass as shown in the illustration.
| *a | Back Side | *b | Ceramic Notch |
68165B
4.INSTALL GLIDE DOOR GLASS MOULDING
Using non-residue solvent, clean the glide door glass moulding installation surface of the glide door glass.
Using a brush or sponge, coat the glass primer to the glide door glass moulding installation surface of the glide door glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new glide door glass moulding.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 2 glide door glass mouldings to the glide door glass as shown in the illustration.
| *a | Back Side | *b | R End |
| Area | Specified Condition |
|---|---|
| a | 11.5 mm (0.453 in.) |
| b | 11.4 mm (0.449 in.) |
| c | 11.3 mm (0.445 in.) |
| d | 11.7 mm (0.461 in.) |
62267U
5.INSTALL SIDE WINDOW ADHESIVE DAM
Using non-residue solvent, clean the side window adhesive dam installation surface of the glide door glass.
Install the glass primer to the side window adhesive dam installation surface of the glide door glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new side window adhesive dam.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the side window adhesive dam to the glide door glass as shown in the illustration.
| *a | Back Side | *b | R End |
| *c | Side of Glide Door Glass Moulding | - | - |
| Area | Specified Condition |
|---|---|
| a | 3.0 mm (0.118 in.) |
| b | 1.5 mm (0.0591 in.) |
| c | 2.8 mm (0.110 in.) |
68294F
6.INSTALL SIDE WINDOW ADHESIVE DAM
Using non-residue solvent, clean the side window adhesive dam installation surface of the glide door glass.
Using a brush or sponge, coat the glass primer to the side window adhesive dam installation surface of the glide door glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new side window adhesive dam.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 3 side window adhesive dams to the glide door glass as shown in the illustration.
| *a | Back Side | *b | Ceramic Notch |
| Area | Specified Condition |
|---|---|
| a | 21.8 mm (0.858 in.) |
68113C
7.INSTALL GLIDE DOOR GLASS
Clean and shape the contact surface of the door panel.
On the contact surface of the door panel, use a knife to cut away excess adhesive as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.) |
Clean the contact surface of the door panel with non-residue solvent.
| *a | Door Panel |
|
Adhesive |
Position the glide door glass.
Using suction cups, place the glide door glass in the correct position.
Check that the entire contact surface of the glass rim is perfectly even.
Using suction cups, remove the glide door glass.
Using a brush or sponge, apply body primer to the exposed part of the door panel.
Do not apply too much primer.
Do not apply primer to the adhesive.
When applying the primer, take care of the seams of the panel and spot welds.
Using a brush or sponge, apply glass primer to the contact surface of the glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | - | - |
|
Glass Primer Application Area | - | - |
| Area | Specified Condition |
|---|---|
| a | 21.9 mm (0.862 in.) |
| b | 19.2 mm (0.756 in.) |
| c | 9.1 mm (0.358 in.) |
| d | 14 mm (0.551 in.) |
| e | 27.1 mm (1.07 in.) |
Apply adhesive to the glide door glass.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| *1 | Sealer Gun |
After cutting off the tip, use all adhesive within the time written in the table below.
Load the sealer gun with the cartridge.
Apply adhesive to the glass as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | Adhesive Center |
|
Adhesive | - | - |
| Area | Specified Condition |
|---|---|
| a | 14.9 mm (0.587 in.) |
| b | 12.1 mm (0.476 in.) |
| c | 8.0 mm (0.315 in.) |
| d | 16.1 mm (0.634 in.) |
| e | 12.2 mm (0.480 in.) |
Install the glide door glass to the door panel.
Using suction cups, attach the 4 glide door fix window pins and install the back door glass.
Press it in gently along the rim.
Check that the 4 glide door fix window pins are attached to the door panel correctly.
Check that the door panel and glass have a small gap between them.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to the glass rim.
Hold the glide door glass using protective tape until the applied adhesive becomes hard.
Do not drive the vehicle for the time described in the table below.
| Temperature | Minimum Time Prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
8.INSPECT FOR LEAKS AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
67745
9.INSTALL CENTER DOOR TRIM MOULDING
Align the installation mark on the back door trim moulding to the cutout of the door panel and install it.
| *a | Installation Mark (Paint) |
62384Q
10.INSTALL SIDE WINDOW CLIP CAP
Install the side window clip cap.
| *1 | Side Window Clip Cap |