Home › Vehicle Exterior › WINDOW / GLASS › REAR SIDE WINDOW GLASS (for No. 2 LH)
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356218 REAR SIDE WINDOW GLASS(for No. 2 LH) A

WINDOW / GLASS  REAR SIDE WINDOW GLASS(for No. 2 LH)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 1.CLEAN REAR SIDE FRONT WINDOW GLASS LH

a.
E268586

Clean the outer edge of the rear side front window glass LH with non-residue solvent.

NOTICE:
·

Do not touch the rear side front window glass LH surface after cleaning it.

·

Do not damage the glass.

·

Even if using a new rear side front window glass LH, clean the rear side front window glass LH with non-residue solvent.




Hide 62269J 2.INSTALL SIDE WINDOW FRAME FILM

NOTICE:

Perform the following procedures when replacing the side window frame film.


HINT:

Remove the adhesive remaining on the installation surface of the side window frame film of the rear side front window glass LH.


a.

Using non-residue solvent, clean the installation surface of the side window frame film of the rear side front window glass LH.


b.

Remove the peeling paper on a new side window frame film while making sure not to touch the adhesional surface.


c.

Install the 10 pieces of side window frame film at the positions shown in the illustration.

B507060E01
2.708,3.615 3.031,3.615 3.031,3.615 3.083,3.531 true 2.479,3.521 2.708,3.698 0.229,0.177 10 false *a 3.313,3.583 3.563,3.729 0.25,0.146 10 false *b 3.958,3.396 4.104,3.563 0.146,0.167 10 false a

Text in Illustration
*a Specified Application Position *b Align the lateral center of the side window frame film with the center of the hole in the rear side front window glass LH.
*c Tape - -

Standard:
Area Specified Condition
a 4.6 mm (0.181 in.)



Hide 62461R 3.INSTALL REAR SIDE WINDOW RUN LH (for Slide Type)

NOTICE:

Perform the following procedures when replacing the rear side window run LH.


HINT:

Remove the adhesive remaining on the installation surface of the rear side window run LH of the rear side front window glass LH.


a.

Using non-residue solvent, clean the installation surface of the rear side window run LH of the rear side front window glass LH.


b.

Apply adhesive to the installation surface of the rear side window run LH of the rear side front window glass LH.

NOTICE:
·

Make sure that the adhesive does not contact any other areas outside of the application area.

·

Clean any protruding adhesive.

·

Apply adhesive to the entire circumference.



B519836E01
6.01,1.479 5.479,1.385 5.479,1.385 6.01,1.177 false 0.281,1.042 0.625,1.354 0.344,0.313 10 false A 0.802,1.042 1.146,1.354 0.344,0.313 10 false A 4.844,0.615 5.51,0.927 0.667,0.313 10 false A-A 5.281,1.313 5.948,1.625 0.667,0.313 10 false *a

Text in Illustration
*a Adhesive - -


c.

Install a new rear side window run LH to the rear side front window glass LH.


Hide 62746G 4.INSTALL QUARTER WINDOW PACKING (for Slide Type)

NOTICE:

Perform the following procedures when replacing the quarter window packing.


HINT:

Clean any adhesive from the installation surface of the quarter window packing on the side window center frame sub-assembly LH.


a.

Using non-residue solvent, clean the installation surface of the quarter window packing of the side window center frame sub-assembly LH.


b.
B471150E01
2.375,0.792 2.531,0.99 0.156,0.198 10 false a

Install a new quarter window packing to the side window center frame sub-assembly LH and keep it in the position shown in the illustration.

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)



c.
B471198

Apply instant adhesive to the fitting surface (dotted line) on the quarter window packing and side window center frame sub-assembly LH to secure the quarter window packing.

NOTICE:

Make sure that instant adhesive does not contact any other areas outside of the application area.



d.
B505393E01
2.51,0.313 2.75,0.115 2.75,0.115 2.885,0.115 true 1.344,0.385 1.5,0.583 0.156,0.198 10 false c 0.396,1.302 0.552,1.5 0.156,0.198 10 false a 0.875,1.906 1.031,2.104 0.156,0.198 10 false b 2.958,0.052 3.198,0.229 0.24,0.177 10 false *a

Prepare an EPT sealer with the dimensions shown in the illustration.

Text in Illustration
*a Seal Area

Standard:
Area Specified Condition
a 5.0 mm (0.197 in.)
b 4.0 mm (0.157 in.)
c 30 mm (1.18 in.)



e.

Remove the peeling paper and install the EPT sealer to the side window center frame sub-assembly at the position shown in the illustration.

B505394E01
1.865,1.208 2.302,0.635 2.302,0.635 2.458,0.635 false 3.26,2.208 4.281,2.208 false 2.51,0.552 2.823,0.75 0.313,0.198 10 false *b 3.042,2.135 3.302,2.323 0.26,0.188 10 false *a 2.74,1.813 2.927,2 0.188,0.188 10 false A 6.688,2.104 6.948,2.292 0.26,0.188 10 false *a 5.781,0.792 6.042,0.979 0.26,0.188 10 false *c

Text in Illustration
*a Application Reference Line a *b Specified Application Position b
*c View A - -


Hide 62910Q 5.INSTALL SIDE WINDOW LOCK ASSEMBLY (for Slide Type, except Glide Type)

HINT:

Use the same procedure for each of the side window lock assemblies.


a.
B471136

Install the side window lock packing.

NOTICE:

If there is extreme damage to the side window lock packing, replace it with a new one.



b.
B471137

Install the side window lock retainer.


c.
B471135

Install the side window lock assembly with 2 screws.

i.

Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the side window lock packing.


iii.

Apply adhesive to the threaded portion of the screw.


iv.

Install the side window lock assembly with the 2 screws.



Hide 62910Q 6.INSTALL SIDE WINDOW LOCK ASSEMBLY (for Slide Type, for Glide Type)

a.
B471136

Install the side window lock packing.

NOTICE:

If there is extreme damage to the side window lock packing, replace it with a new one.



b.
B471137

Install the side window lock retainer.


c.
B471135

Install the side window lock assembly with 2 screws.

i.

Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the side window lock packing.


iii.

Apply adhesive to the threaded portion of the screw.


iv.

Install the side window lock assembly with the 2 screws.



Hide 62777E 7.INSTALL SIDE WINDOW CENTER SASH CAP (for Slide Type)

NOTICE:

Perform the following procedures when replacing the side window center sash cap.


a.
B507065E01
0.542,1.823 0.76,2.021 0.219,0.198 10 false *a

Install a new side window center sash cap to the rear side front window glass LH at the position shown in the illustration.

Text in Illustration
*a Vehicle Front


Hide 62221L 8.INSTALL REAR SIDE WINDOW GLASS LH (for Slide Type)

NOTICE:
·

Do not damage the rear side front window glass LH.

·

Do not damage the window frame.

·

Do not damage the rear side window glass LH.



a.
B475099

Widen top and bottom of the window frame using your hands and install the rear side window glass LH.


b.
B475098

Install the center side window frame sub-assembly.


c.

Install the screw:

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the rear side window glass LH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.



Hide 62221K 9.INSTALL FRONT SIDE WINDOW GLASS LH (for Slide Type)

NOTICE:
·

Do not damage the rear side front window glass LH.

·

Do not damage the window frame.

·

Do not damage the front side window glass LH.



a.
B475097

Widen top and bottom of the window frame using your hands and install the rear side front window glass LH.


b.
B475096

Install the screw:

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the rear side front window glass LH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.


v.
B471199E01
1.229,0.208 1.385,0.406 0.156,0.198 10 false a 2.031,0.208 2.188,0.406 0.156,0.198 10 false a 2.906,1.031 3.063,1.229 0.156,0.198 10 false b

Apply sealant (water proof) to the head of the screw in the area shown in the illustration.

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)
b 12.2 mm (0.480 in.)




Hide 62391F 10.INSTALL NO. 1 SIDE WINDOW STOPPER (for Slide Type)

a.

Install the No. 1 side window stopper.

B505386E02
2.156,2.5 2.688,2.813 2.688,2.813 3.271,2.458 false 2.552,3.49 2.625,3.313 false 0.271,1.885 0.563,2.094 0.292,0.208 12 false *A 0.271,2.688 0.563,2.896 0.292,0.208 12 false *B 2.594,2.844 2.906,3.042 0.313,0.198 10 false *1 2.417,3.5 2.729,3.698 0.313,0.198 10 false *1

Text in Illustration
*A except Glide Type *B for Glide Type
*1 No. 1 Side Window Stopper - -

i.

Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the No. 1 side window stopper screw.


iii.

Apply adhesive to the threaded portion of the screw.


iv.

Install a new No. 1 side window stopper with the 2 screws.



Hide 62763R 11.INSTALL SIDE WINDOW FRAME RETAINER

a.

Using non-residue solvent, clean the side window frame retainer installation surface of the rear side front window glass LH.


b.

Install the primer to the side window frame retainer installation surface of the rear side front window glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

for Slide Type:

i.

Remove the peeling paper from a new side window frame retainer.


ii.

Install the 4 side window frame retainers to the rear side front window glass LH as shown in the illustration.

B477315E01
5.51,1.427 5.885,1.313 false 0.063,0.052 0.448,0.313 0.385,0.26 10 false *a 3.24,0.323 3.625,0.583 0.385,0.26 10 false b 3.979,0.188 4.365,0.448 0.385,0.26 10 false a 2.448,0.49 2.833,0.75 0.385,0.26 10 false c 1.75,0.646 2.135,0.906 0.385,0.26 10 false d 3.031,0.781 3.417,1.042 0.385,0.26 10 false A 3.021,0.969 3.135,1.24 0.115,0.271 10 true A 5.469,0.656 5.927,0.948 0.458,0.292 10 false A-A 5.333,1.365 5.719,1.625 0.385,0.26 10 false *1

Text in Illustration
*1 Side Window Frame Retainer - -
*a Back Side - -

Standard:
Area Specified Condition
a 203.8 mm (8.02 in.)
b 523.5 mm (20.6 in.)
c 939.8 mm (37.0 in.)
d 1323.5 mm (52.1 in.)




d.

for Fixed Type:

i.

Remove the peeling paper from a new side window frame retainer.


ii.

Install the 4 side window frame retainers to the rear side front window glass LH as shown in the illustration.

B477316E01
5.594,1.396 5.917,1.313 false 0.115,0.083 0.615,0.375 0.5,0.292 10 false *a 1.74,0.656 2.24,0.948 0.5,0.292 10 false d 2.458,0.479 2.958,0.771 0.5,0.292 10 false c 3.271,0.333 3.771,0.625 0.5,0.292 10 false b 4.031,0.198 4.531,0.49 0.5,0.292 10 false a 5.896,0.625 6.396,0.917 0.5,0.292 10 false A-A 5.427,1.344 5.927,1.635 0.5,0.292 10 false *1 3.031,0.781 3.531,1.073 0.5,0.292 10 false A 3.021,0.979 3.156,1.24 0.135,0.26 10 true A

Text in Illustration
*1 Side Window Frame Retainer - -
*a Back Side *b Ceramic Notch

Standard:
Area Specified Condition
a 120.6 mm (4.75 in.)
b 504.4 mm (19.9 in.)
c 920.6 mm (36.2 in.)
d 1304.4 mm (51.4 in.)




Hide 62785S 12.INSTALL SIDE WINDOW GLASS SPACER

a.

Using non-residue solvent, clean the side window glass spacer installation surface of the rear side front window glass RH.


b.

Install the primer to the side window glass spacer installation surface of the rear side front window glass RH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new side window glass spacer.

i.

for Glide Type, Slide Type:

1.

Install the 4 side window glass spacers to the rear side front window glass LH as shown in the illustration.

B475104E01
0.5,0.719 0.646,0.719 true 0.5,2.073 0.646,2.073 true 0.854,0.427 1.031,0.521 true 0.76,1.073 1.021,0.938 true 0.875,1.781 1.052,1.875 true 0.802,2.417 1.063,2.281 true 5.771,0.333 6.063,0.521 true 5.771,1.604 6.063,1.792 true 6.448,0.438 6.552,0.438 true 6.427,0.708 6.542,0.708 true 6.375,1.073 6.542,1 true 6.417,1.802 6.521,1.802 true 6.406,2.094 6.521,2.094 true 6.344,2.469 6.51,2.396 true 0.135,0.104 0.375,0.271 0.24,0.167 10 false *a 0.313,0.656 0.531,0.823 0.219,0.167 10 false *1 0.323,2 0.542,2.167 0.219,0.167 10 false *1 1.052,0.479 1.271,0.646 0.219,0.167 10 false *b 1.052,0.823 1.271,0.99 0.219,0.167 10 false *b 1.063,1.781 1.281,1.948 0.219,0.167 10 false *b 1.083,2.167 1.302,2.333 0.219,0.167 10 false *b 5.552,0.229 5.771,0.396 0.219,0.167 10 false *2 5.542,1.448 5.76,1.615 0.219,0.167 10 false *2 6.573,0.385 6.792,0.552 0.219,0.167 10 false *b 6.583,0.646 6.802,0.813 0.219,0.167 10 false *1 6.573,0.885 6.792,1.052 0.219,0.167 10 false *b 6.552,1.75 6.771,1.917 0.219,0.167 10 false *b 6.563,2.01 6.781,2.177 0.219,0.167 10 false *1 6.573,2.26 6.792,2.427 0.219,0.167 10 false *b

Text in Illustration
*1 Side Window Glass Spacer *2 EPT sealer
*a Back Side *b Ceramic Notch



ii.

for Folding Type, Slide Type:

1.

Install the 4 side window glass spacers to the rear side front window glass LH as shown in the illustration.

B475105E01
0.854,0.427 1.021,0.531 true 0.771,1.083 1.021,1.01 true 0.865,1.771 1.031,1.875 true 0.802,2.417 1.01,2.333 true 0.646,0.719 0.5,0.719 true 0.656,2.073 0.51,2.073 true 6.229,0.729 6.083,0.729 true 6.208,2.115 6.063,2.115 true 6.313,0.323 6.385,0.406 false 6.323,2.469 6.24,2.469 false 6.49,0.667 6.563,0.75 false 6.49,2.01 6.573,2.104 false 6.25,1.688 6.323,1.771 false 6.292,1.083 6.24,1.135 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.302,0.656 0.521,0.823 0.219,0.167 10 false *1 0.323,1.99 0.542,2.156 0.219,0.167 10 false *1 6.604,0.708 6.823,0.875 0.219,0.167 10 false *2 6.615,2.073 6.833,2.24 0.219,0.167 10 false *2 6.125,0.24 6.344,0.406 0.219,0.167 10 false *b 6.073,1.073 6.292,1.24 0.219,0.167 10 false *b 5.875,0.656 6.083,0.823 0.208,0.167 10 true *1 6.073,1.615 6.292,1.781 0.219,0.167 10 false *b 5.854,2.042 6.063,2.208 0.208,0.167 10 true *1 6.063,2.396 6.281,2.563 0.219,0.167 10 false *b 1.073,0.49 1.292,0.656 0.219,0.167 10 false *b 1.052,0.917 1.271,1.083 0.219,0.167 10 false *b 1.052,1.76 1.271,1.927 0.219,0.167 10 false *b 1.042,2.229 1.26,2.396 0.219,0.167 10 false *b

Text in Illustration
*1 Side Window Glass Spacer *2 EPT sealer
*a Back Side *b Ceramic Notch



iii.

for Fixed Type:

1.

Install the 4 side window glass spacers to the rear side front window glass LH as shown in the illustration.

B475106E01
0.594,0.51 0.854,0.427 true 0.615,0.979 0.771,0.927 true 0.552,0.75 0.76,0.75 true 0.604,1.833 0.708,1.792 true 0.542,2.094 0.708,2.094 true 0.573,2.344 0.698,2.417 true 6.156,0.396 6.24,0.417 false 6.063,0.75 6.146,0.75 false 6.177,0.938 6.073,1.323 6.073,1.323 6.333,0.948 true 6.479,0.74 6.594,0.74 false 6.26,1.75 5.958,1.604 true 6.063,2.073 6.146,2.073 false 6.052,2.604 6.281,2.385 true 6.479,2.052 6.594,2.052 false 0.969,0.896 1.052,0.958 false 0.396,0.448 0.615,0.604 0.219,0.156 10 false *b 0.354,0.677 0.573,0.833 0.219,0.156 10 false *1 0.417,0.917 0.635,1.073 0.219,0.156 10 false *b 1.063,0.938 1.281,1.094 0.219,0.156 10 false *b 0.406,1.771 0.625,1.927 0.219,0.156 10 false *b 0.354,2.021 0.573,2.177 0.219,0.156 10 false *1 0.365,2.26 0.583,2.417 0.219,0.156 10 false *b 5.979,0.344 6.198,0.5 0.219,0.156 10 false *b 5.896,1.281 6.115,1.438 0.219,0.156 10 false *b 5.771,1.51 5.99,1.667 0.219,0.156 10 false *b 5.844,2.563 6.063,2.719 0.219,0.156 10 false *b 6.656,0.667 6.875,0.823 0.219,0.156 10 false *2 6.646,1.979 6.865,2.135 0.219,0.156 10 false *2 5.865,0.688 6.083,0.844 0.219,0.156 10 false *1 5.875,2 6.094,2.156 0.219,0.156 10 false *1

Text in Illustration
*1 Side Window Glass Spacer *2 EPT sealer
*a Back Side *b Ceramic Notch