Home › Vehicle Exterior › WINDOW / GLASS › REAR SIDE WINDOW GLASS (for No. 3 LH)
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356219 REAR SIDE WINDOW GLASS(for No. 3 LH) A

WINDOW / GLASS  REAR SIDE WINDOW GLASS(for No. 3 LH)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 1.CLEAN REAR SIDE WINDOW FRONT GLASS LH

a.
E268586

Clean the outer edge of the rear side front window glass LH with non-residue solvent.

NOTICE:
·

Do not touch the rear side front window glass LH surface after cleaning it.

·

Do not damage the glass.

·

Even if using a new rear side front window glass LH, clean the rear side front window glass LH with non-residue solvent.




Hide 62269L 2.INSTALL SIDE WINDOW FRAME FILM

NOTICE:

Perform the following procedures when replacing the side window frame film.


HINT:

Remove the adhesive remaining on the installation surface of the side window frame film of the rear side front window glass LH.


a.

Using non-residue solvent, clean the installation surface of the side window frame film of the rear side front window glass LH.


b.

Remove the peeling paper on a new side window frame film while making sure not to touch the adhesional surface.


c.

Install the 10 pieces of side window frame film at the positions shown in the illustration.

B507061E01
2.708,3.635 3.021,3.635 3.021,3.635 3.063,3.563 true 2.49,3.552 2.688,3.729 0.198,0.177 10 false *a 3.302,3.594 3.5,3.75 0.198,0.156 10 false *b 3.958,3.417 4.104,3.594 0.146,0.177 10 false a

Text in Illustration
*a Specified Application Position *b Align the lateral center of the side window frame film with the center of the hole in the front rear side front window glass LH.
V100155

Tape - -

Standard:
Area Specified Condition
a 4.6 mm (0.181 in.)



Hide 62461S 3.INSTALL REAR SIDE WINDOW RUN LH (for Slide Type)

NOTICE:

Perform the following procedures when replacing the rear side window run LH.


HINT:

Remove the adhesive remaining on the installation surface of the rear side window run LH of the rear side front window glass LH.


a.

Using non-residue solvent, clean the installation surface of the rear side window run LH of the rear side front window glass LH.


b.

Apply adhesive to the installation surface of the rear side window run LH of the rear side front window glass LH.

NOTICE:
·

Make sure that the adhesive does not contact any other areas outside of the application area.

·

Clean any protruding adhesive.

·

Apply adhesive to the entire circumference.



B506641E01
6.01,1.49 5.531,1.406 5.531,1.406 6,1.156 true 0.281,1.042 0.438,1.24 0.156,0.198 10 false A 0.802,1.042 0.958,1.24 0.156,0.198 10 false A 4.781,0.427 5.188,0.594 0.406,0.167 10 false A-A 5.302,1.333 5.542,1.521 0.24,0.188 10 false *a

Text in Illustration
*a Adhesive - -


c.

Install a new rear side window run LH to the rear side front window glass LH.


Hide 62746G 4.INSTALL QUARTER WINDOW PACKING (for Slide Type)

NOTICE:

Perform the following procedures when replacing the quarter window packing.


HINT:

Clean any adhesive from the installation surface of the quarter window packing on the side window center frame sub-assembly LH.


a.

Using non-residue solvent, clean the installation surface of the quarter window packing of the side window center frame sub-assembly LH.


b.
B471150E01
2.375,0.792 2.531,0.99 0.156,0.198 10 false a

Install a new quarter window packing to the side window center frame sub-assembly LH and keep it in the position shown in the illustration.

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)



c.
B471198

Apply instant adhesive to the fitting surface (dotted line) on the quarter window packing and side window center frame sub-assembly LH to secure the quarter window packing.

NOTICE:

Make sure that instant adhesive does not contact any other areas outside of the application area.



d.
B505393E01
2.51,0.313 2.75,0.115 2.75,0.115 2.885,0.115 true 1.344,0.385 1.5,0.583 0.156,0.198 10 false c 0.396,1.302 0.552,1.5 0.156,0.198 10 false a 0.875,1.906 1.031,2.104 0.156,0.198 10 false b 2.958,0.052 3.198,0.229 0.24,0.177 10 false *a

Prepare an EPT sealer with the dimensions shown in the illustration.

HINT:

A generic EPT sealer can be used.


Text in Illustration
*1 Seal Area

Standard:
Area Specified Condition
a 5.0 mm (0.197 in.)
b 4.0 mm (0.157 in.)
c 30 mm (1.18 in.)



e.

Remove the peeling paper and install the EPT sealer to the side window center frame sub-assembly at the position shown in the illustration.

B505394E01
1.865,1.208 2.302,0.635 2.302,0.635 2.458,0.635 false 3.26,2.208 4.281,2.208 false 2.51,0.552 2.823,0.75 0.313,0.198 10 false *b 3.042,2.135 3.302,2.323 0.26,0.188 10 false *a 2.74,1.813 2.927,2 0.188,0.188 10 false A 6.688,2.104 6.948,2.292 0.26,0.188 10 false *a 5.781,0.792 6.042,0.979 0.26,0.188 10 false *c

Text in Illustration
*a Application Reference Line a *b Specified Application Position b
*c View A - -


Hide 62910R 5.INSTALL SIDE WINDOW LOCK ASSEMBLY

HINT:

Use the same procedure for each of the side window lock assemblies.


a.
B471136

Install the side window lock packing.

NOTICE:

If there is extreme damage to the side window lock packing, replace it with a new one.



b.
B471137

Install the side window lock retainer.


c.
B471135

Install the side window lock assembly with 2 screws.

i.

Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the side window lock packing.


iii.

Apply adhesive to the threaded portion of the screw.


iv.

Install the side window lock assembly with the 2 screws.



Hide 62777G 6.INSTALL SIDE WINDOW CENTER SASH CAP (for Slide Type)

NOTICE:

Perform the following procedures when replacing the side window center sash cap.


a.
B507065E01
0.542,1.823 0.76,2.021 0.219,0.198 10 false *a

Install a new side window center sash cap to the rear side front window glass LH at the position shown in the illustration.

Text in Illustration
*a Vehicle Front


Hide 62221M 7.INSTALL REAR SIDE WINDOW GLASS LH

NOTICE:
·

Do not damage the rear side front window glass LH.

·

Do not damage the window frame.

·

Do not damage the rear side window glass LH.



a.

Widen top and bottom of the window frame using your hands and install the rear side window glass LH.

B475112E01
0.844,0.146 1.156,0.344 0.313,0.198 12 false *A 4.021,0.146 4.333,0.344 0.313,0.198 12 false *B

Text in Illustration
*A for Long Body *B for Standard Body


b.

Install the center side window frame sub-assembly.

B475111E01
0.719,0.115 1.094,0.354 0.375,0.24 12 false *A 3.885,0.125 4.26,0.365 0.375,0.24 12 false *B

Text in Illustration
*A for Long Body *B for Standard Body


c.

Install the screw:

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the rear side front window glass LH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.



Hide 62221N 8.INSTALL FRONT SIDE WINDOW GLASS LH

NOTICE:
·

Do not damage the rear side front window glass LH.

·

Do not damage the window frame.

·

Do not damage the front side window glass LH.



a.

Widen top and bottom of the window frame using your hands and install the front side window glass LH.

B475110E01
0.781,0.125 1.156,0.365 0.375,0.24 12 false *A 3.969,0.167 4.344,0.406 0.375,0.24 12 false *B

Text in Illustration
*A for Long Body *B for Standard Body


b.

Install the screw:

B475109E01
0.646,0.135 1.021,0.375 0.375,0.24 12 false *A 4.063,0.125 4.438,0.365 0.375,0.24 12 false *B

Text in Illustration
*A for Long Body *B for Standard Body

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the rear side front window glass LH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.


v.
B471199E01
1.229,0.208 1.385,0.406 0.156,0.198 10 false a 2.031,0.208 2.188,0.406 0.156,0.198 10 false a 2.906,1.031 3.063,1.229 0.156,0.198 10 false b

Apply sealant (water proof) to the head of the screw in the area shown in the illustration

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)
b 12.2 mm (0.480 in.)




Hide 62391H 9.INSTALL NO. 1 SIDE WINDOW STOPPER (for Slide Type)

a.

Install the No. 1 side window stopper.

B505405E01
2.198,3.021 2.74,3.365 2.74,3.365 3.313,2.969 false 2.698,3.427 3.01,3.625 0.313,0.198 10 false *1

Text in Illustration
*1 No. 1 Side Window Stopper - -

i.

Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the No. 1 side window stopper screw.


iii.

Apply adhesive to the threaded portion of the screw.


iv.

Install a new No. 1 side window stopper with the 2 screws.



Hide 62763U 10.INSTALL SIDE WINDOW FRAME RETAINER

a.

Using non-residue solvent, clean the side window frame retainer installation surface of the rear side front window glass LH.


b.

Install the primer to the side window frame retainer installation surface of the rear side front window glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

for Long Body, Slide Type:

i.

Remove the peeling paper from a new side window frame retainer.


ii.

Install the 4 side window frame retainers to the rear side front window glass LH as shown in the illustration.

B476276E01
1.917,1.26 2.292,1.458 false 1.156,0.667 1.521,0.833 0.365,0.167 10 false A-A 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 2.354,1.427 2.688,1.719 0.333,0.292 10 false *1 3.74,0.188 3.896,0.385 0.156,0.198 10 false a 4.469,0.344 4.625,0.542 0.156,0.198 10 false b 5.26,0.5 5.417,0.698 0.156,0.198 10 false c 6,0.656 6.156,0.854 0.156,0.198 10 false d 4.688,0.781 4.844,0.979 0.156,0.198 10 false A 4.688,0.979 4.844,1.177 0.156,0.198 10 true A

Text in Illustration
*1 Side Window Frame Retainer - -
*a Back Side - -

Area Specified Condition
a 203.8 mm (8.02 in.)
b 523.5 mm (20.6 in.)
c 939.8 mm (37.0 in.)
d 1323.5 mm (52.1 in.)



d.

for Long Body, Fixed Type:

i.

Remove the peeling paper from a new side window frame retainer.


ii.

Install the 4 side window frame retainers to the rear side front window glass LH as shown in the illustration.

B477313E01
1.167,1.25 1.521,1.25 false 0.198,0.115 0.51,0.313 0.313,0.198 10 false *a 1.021,0.688 1.333,0.885 0.313,0.198 10 false A-A 0.979,1.177 1.333,1.427 0.354,0.25 10 false *1 5.906,0.198 6.063,0.365 0.156,0.167 10 false a 5.167,0.354 5.323,0.521 0.156,0.167 10 false b 4.365,0.5 4.521,0.667 0.156,0.167 10 false c 3.625,0.656 3.781,0.823 0.156,0.167 10 false d 4.958,0.792 5.115,0.958 0.156,0.167 10 false A 4.958,0.979 5.094,1.146 0.135,0.167 10 true A

Text in Illustration
*1 Side Window Frame Retainer - -
*a Back Side - -

Standard:
Area Specified Condition
a 120.6 mm (4.75 in.)
b 504.4 mm (19.9 in.)
c 920.6 mm (36.2 in.)
d 1304.4 mm (51.4 in.)




e.

for Standard Body, Slide Type:

i.

Remove the peeling paper from a new side window frame retainer.


ii.

Install the 4 side window frame retainers to the rear side front window glass LH as shown in the illustration.

B475113E01
4.708,0.604 5.052,0.792 0.344,0.188 10 false A-A 3.229,0.198 3.385,0.365 0.156,0.167 10 false a 2.479,0.354 2.635,0.521 0.156,0.167 10 false b 1.656,0.5 1.813,0.667 0.156,0.167 10 false c 1.188,0.656 1.344,0.823 0.156,0.167 10 false d 2.292,0.781 2.448,0.948 0.156,0.167 10 false A 2.292,0.979 2.438,1.146 0.146,0.167 10 true A 0.156,0.135 0.635,0.458 0.479,0.323 10 false *a

Text in Illustration
*1 Side Window Frame Retainer - -
*a Back Side - -

Standard:
Area Specified Condition
a 115.6 mm (4.55 in.)
b 499.4 mm (19.7 in.)
c 915.6 mm (36.0 in.)
d 1159.6 mm (45.7 in.)




f.

for Standard Body, Fixed Type:

i.

Remove the peeling paper from a new side window frame retainer.


ii.

Install the 4 side window frame retainers to the rear side front window glass LH as shown in the illustration.

B477314E01
1.198,1.26 1.583,1.26 false 0.198,0.125 0.51,0.323 0.313,0.198 10 false *a 1,0.604 1.365,0.792 0.365,0.188 10 false A-A 0.958,1.188 1.198,1.344 0.24,0.156 10 false *1 5.969,0.219 6.125,0.375 0.156,0.156 10 false a 5.229,0.354 5.385,0.51 0.156,0.156 10 false b 4.406,0.51 4.563,0.667 0.156,0.156 10 false c 3.938,0.667 4.094,0.823 0.156,0.156 10 false d 5.021,0.76 5.177,0.917 0.156,0.156 10 false A 5.021,0.958 5.167,1.115 0.146,0.156 10 true A

Text in Illustration
*1 Side Window Frame Retainer - -
*a Back Side - -

Standard:
Area Specified Condition
a 120.6 mm (4.75 in.)
b 504.4 mm (19.9 in.)
c 920.6 mm (36.2 in.)
d 1164.5 mm (45.8 in.)




Hide 62785V 11.INSTALL SIDE WINDOW GLASS SPACER

a.

Using non-residue solvent, clean the side window glass spacer installation surface of the rear side front window glass LH.


b.

Install the primer to the side window glass spacer installation surface of the rear side front window glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

for Long Body, Slide Type:

i.

Remove the peeling paper from a new side window glass spacer.


ii.

Install the 4 side window glass spacers to the rear side window front glass LH as shown in the illustration.

B476278E01
1.24,0.979 1.365,0.979 false 1.25,0.771 1.458,0.698 true 1.188,1.219 1.406,1.302 true 1.25,1.604 1.479,1.563 true 1.188,2.073 1.458,2.146 true 1.24,1.813 1.365,1.813 false 5.74,0.719 5.917,0.771 true 6,1.208 5.823,1.271 true 5.74,1.563 5.917,1.615 true 5.979,2.073 5.76,2.156 true 5.781,0.969 5.917,0.969 false 5.781,1.823 5.927,1.823 false 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.49,0.594 1.698,0.75 0.208,0.156 10 false *b 1.469,1.229 1.677,1.385 0.208,0.156 10 true *b 5.563,0.604 5.771,0.76 0.208,0.156 10 true *b 5.615,1.229 5.823,1.385 0.208,0.156 10 true *b 5.521,1.469 5.729,1.625 0.208,0.156 10 true *b 5.573,2.094 5.781,2.25 0.208,0.156 10 true *b 1.365,0.896 1.573,1.052 0.208,0.156 10 false *1 1.521,1.479 1.729,1.635 0.208,0.156 10 true *b 1.521,2.104 1.729,2.26 0.208,0.156 10 true *b 1.375,1.729 1.583,1.885 0.208,0.156 10 false *1 5.635,0.896 5.917,1.125 0.281,0.229 10 false *1 5.635,1.76 5.896,1.99 0.26,0.229 10 false *1

Text in Illustration
*1 Side Window Glass Spacer - -
*a Back Side *b Ceramic Notch



d.

for Long Body, Fixed Type:

i.

Remove the peeling paper from a new side window glass spacer.


ii.

Install the 4 side window glass spacers to the rear side window front glass LH as shown in the illustration.

B476279E01
1.188,0.76 1.448,0.698 true 1.25,1.083 1.385,1.188 true 0.896,0.969 1.073,0.969 false 1.063,1.104 0.958,1.188 true 0.896,1.833 1.063,1.833 false 1.229,1.604 1.49,1.542 true 1.24,2.063 1.427,2.219 true 5.802,0.677 5.958,0.771 true 6.104,0.99 6.271,0.99 false 5.917,1.104 5.792,1.208 true 6.219,1.208 6.104,1.104 true 5.76,1.51 5.917,1.604 true 5.906,2.094 5.781,2.198 true 6.104,1.823 6.271,1.823 false 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 1.49,0.615 1.729,0.792 0.24,0.177 10 true *b 1.438,1.146 1.677,1.323 0.24,0.177 10 true *b 1.531,1.458 1.771,1.635 0.24,0.177 10 true *b 1.479,2.188 1.719,2.365 0.24,0.177 10 true *b 5.615,0.542 5.823,0.719 0.208,0.177 10 true *b 5.583,1.177 5.781,1.354 0.198,0.177 10 true *b 5.552,1.417 5.771,1.594 0.219,0.177 10 true *b 5.594,2.167 5.802,2.344 0.208,0.177 10 true *b 0.76,1.177 0.969,1.354 0.208,0.177 10 true *b 0.688,0.896 0.906,1.052 0.219,0.156 10 true *1 0.688,1.781 0.896,1.938 0.208,0.156 10 true *1 6.323,0.917 6.563,1.094 0.24,0.177 10 true *1 6.323,1.76 6.563,1.938 0.24,0.177 10 true *1 6.24,1.177 6.438,1.354 0.198,0.177 10 true *b

Text in Illustration
*1 Side Window Glass Spacer - -
*a Back Side *b Ceramic Notch



e.

for Standard Body, Slide Type:

i.

Remove the peeling paper from a new side window glass spacer.


ii.

Install the 4 side window frame spacers to the rear side front window glass LH as shown in the illustration.

B477301E01
1.24,0.771 1.344,0.771 true 1.188,1.208 1.396,1.323 true 1.25,1.615 1.354,1.615 true 1.188,2.052 1.302,2.094 true 0.875,0.979 1.052,0.979 false 0.885,1.823 1.063,1.823 false 6.104,0.979 6.281,0.979 false 5.833,0.729 5.927,0.771 true 6.021,1.219 5.813,1.25 true 5.802,1.583 5.927,1.604 true 5.969,2.073 5.802,2.156 true 6.094,1.823 6.271,1.823 false 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.385,0.688 1.615,0.865 0.229,0.177 10 true *b 1.448,1.26 1.677,1.438 0.229,0.177 10 true *b 1.396,1.531 1.625,1.708 0.229,0.177 10 true *b 1.323,2.042 1.552,2.219 0.229,0.177 10 true *b 5.625,0.635 5.854,0.813 0.229,0.177 10 true *b 5.615,1.167 5.844,1.344 0.229,0.177 10 true *b 5.615,1.5 5.844,1.677 0.229,0.177 10 true *b 5.604,2.104 5.833,2.281 0.229,0.177 10 true *b 0.667,0.917 0.896,1.094 0.229,0.177 10 true *1 0.635,1.75 0.865,1.927 0.229,0.177 10 true *1 6.313,0.917 6.542,1.094 0.229,0.177 10 true *1 6.313,1.75 6.542,1.927 0.229,0.177 10 true *1

Text in Illustration
*1 Side Window Glass Spacer - -
*a Back Side *b Ceramic Notch



f.

for Standard Body, Fixed Type:

i.

Remove the peeling paper from a new side window glass spacer.


ii.

Install the 4 side window glass spacers to the rear side window front glass LH as shown in the illustration.

B477302E01
6.094,0.979 6.229,0.979 false 6.094,1.833 6.229,1.833 false 0.896,0.979 1.083,0.979 true 0.885,1.844 1.073,1.844 true 1.208,0.771 1.313,0.74 true 1.25,1.094 1.344,1.208 true 1.094,1.094 0.99,1.198 true 1.24,1.594 1.344,1.563 true 1.229,2.104 1.323,2.219 true 5.844,0.75 5.958,0.771 true 5.813,1.583 5.927,1.604 true 5.938,2.094 5.833,2.198 true 6.094,1.104 6,1.26 6,1.26 5.927,1.083 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.688,0.906 0.906,1.083 0.219,0.177 10 true *1 0.667,1.771 0.885,1.948 0.219,0.177 10 true *1 6.292,0.896 6.51,1.073 0.219,0.177 10 true *1 6.271,1.75 6.49,1.927 0.219,0.177 10 true *1 1.365,0.667 1.583,0.844 0.219,0.177 10 true *b 1.385,1.156 1.604,1.333 0.219,0.177 10 true *b 1.396,1.448 1.615,1.625 0.219,0.177 10 true *b 1.375,2.167 1.594,2.344 0.219,0.177 10 true *b 0.771,1.177 0.99,1.354 0.219,0.177 10 true *b 5.615,0.625 5.813,0.833 0.198,0.208 10 true *b 5.906,1.292 6.125,1.469 0.219,0.177 10 true *b 5.615,1.49 5.771,1.677 0.156,0.188 10 true *b 5.646,2.156 5.865,2.333 0.219,0.177 10 true *b

Text in Illustration
*1 Side Window Glass Spacer - -
*a Back Side *b Ceramic Notch