Home › Vehicle Interior › AIR CONDITIONING › COMPRESSOR (for N04C-VL)
RM2850E _58 Vehicle Interior _073207 AIR CONDITIONING _0356306 COMPRESSOR(for N04C-VL) A

AIR CONDITIONING  COMPRESSOR(for N04C-VL)  REASSEMBLY  


PROCEDURE

Hide 88410 1.INSTALL MAGNET CLUTCH ASSEMBLY

a.
I103030E01
0.521,0.76 0.927,0.927 false 0.354,0.656 0.667,0.854 0.313,0.198 10 false *1

Install the magnet clutch stator with the 3 bolts.

Torque:

7.9 N*m (81 kgf*cm, 70 in.*lbf)


Text in Illustration
*1 Magnet Clutch Stator


b.

Install the ground wire with the bolt.


c.
I103028E01
0.677,0.635 1.031,0.771 false 0.49,0.531 0.802,0.729 0.313,0.198 10 false *1

Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing outward.

Text in Illustration
*1 Magnet Clutch Rotor

NOTICE:

Do not damage the seal cover of the bearing when installing the snap ring.



d.

Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Do not change the combination of the magnet clutch washer(s) used before disassembly.



e.
I105369E02
0.667,1.083 0.917,0.948 false 1.792,0.938 2.875,0.5 true 0.365,1.021 0.698,1.198 0.333,0.177 10 false SST 2.917,0.365 3.229,0.563 0.313,0.198 10 false *1

Using SST, secure the magnet clutch hub and install the nut.

SST
09985-00030  

Torque:

23 N*m (235 kgf*cm, 17 ft.*lbf)


Text in Illustration
*1 Magnet Clutch Hub

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt, and clutch hub.



Hide 88410 2.INSPECT MAGNET CLUTCH CLEARANCE

a.
I103031E06
1.49,2.792 1.667,3.021 true 0.5,0.844 0.865,0.844 true 0.323,0.25 0.688,0.479 0.365,0.229 10 false *a 0.854,0.76 1.219,0.99 0.365,0.229 10 false 1 2.906,1 3.271,1.229 0.365,0.229 10 false *2 1.615,3.031 1.979,3.26 0.365,0.229 10 false *1 0.146,0.76 0.604,0.958 0.458,0.198 10 false MG+

Clamp the compressor in a vise.


b.

Set the dial indicator to the magnet clutch hub.


c.

Connect the positive battery lead to terminal 1 (MG+) of the magnet clutch connector and the negative lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard clearance:

0.6 to 1.0 mm (0.024 to 0.039 in.)


Text in Illustration
*1 Magnet Clutch Hub
*2 Battery

If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using a magnet clutch washer or combination of washers.

NOTICE:

Adjustment should be performed with 3 or less magnet clutch washers.



d.

Remove the compressor and magnet clutch from the vise.


Hide 88688K 3.INSTALL COOLER COMPRESSOR BRACKET

a.
E315834

Install the bracket with the bolt.


b.

Connect the connector clamp.