Home › Vehicle Interior › AIR CONDITIONING › COMPRESSOR (for 14B) › 2017.01–2019.08
RM2850E _58 Vehicle Interior _073207 AIR CONDITIONING _0356307 COMPRESSOR(for 14B) A

AIR CONDITIONING  COMPRESSOR(for 14B)  SHAFT SEAL REPLACEMENT  


CAUTION / NOTICE / HINT

E393768

PROCEDURE

Hide 1.REMOVE SERVICE VALVE

Using SST, remove the 4 bolts holding the service valve.

SST 07110-61050

E393769

Hide 2.DRAIN COMPRESSOR OIL INTO MEASURING FLASK

Measure the quantity of drained oil because the same amount should be replaced later.

Hide 3.REMOVE FELT

Using a screwdriver, remove the felt from the front housing.

E393770

Hide 4.REMOVE KEY

Using SST, remove the key from the shaft.

SST 07712-45021

E393771

Hide 5.REMOVE FRONT HOUSING

a.
E393772

Remove the 5 through bolts.

HINT:

Do not reuse 5 washers.



b.
E393773

Install SST onto the shaft.

SST 95042-10810


c.

Using a screwdriver, remove the front housing.

NOTICE:

Be careful not to scratch the sealing surface of the front housing.



Hide 6.REMOVE SHAFT SEAL

a.
E393774

Using SST, remove the snap ring.

SST 07714-84010


b.
E393775

Using SST, remove the shaft seal.

SST 95042-10611

SST 95042-20420


c.
E393776

Install SST onto the shaft, and pull the mechanical seal upward.

SST 95042-10810


d.
E393777

Using the brass bar and plastic hammer, remove the seal plate.


Hide 7.REMOVE REAR HOUSING

Using a screwdriver, remove the rear housing.

E393778

NOTICE:

Be careful not to scratch the sealing surface of the rear housing.


Hide 8.REMOVE GASKET, VALVE PLATE, SUCTION REED VALVE AND O-RING

a.
E393779

Remove the 2 pins from the front housing. Discard the pins.


b.

Remove O-ring, suction reed valve, valve plate and gasket.


c.
E393780

Remove the 2 pins from the rear housing. Discard the pins.


d.

Remove the O-ring, gasket, suction reed valve, valve plate and gasket. Discard them.


Hide 9.INSTALL REAR HOUSING

a.
E394755

Install the 2 pins in the rear cylinder.


b.

Lubricate a new O-ring with compressor oil. Install the O-ring in the. rear cylinder.


c.
E394756

Install the suction reed valve over the pins on the rear cylinder.


d.
E394757

Install the valve plate together with the discharge reed valve over the pins on the rear cylinder.


e.
E394758

Lubricate the new gasket with compressor oil.


f.

Install the gasket over the pins on the rear cylinder.


g.
E394759

Install the rear housing over the pins on the rear cylinder.


Hide 10.INSTALL FRONT HOUSING

a.
E394760

Install the 2 pins in the front cylinder.


b.

Lubricate a new O-ring with compressor oil. Install the O-ring in the front housing.


c.
E394761

Install the suction reed valve over the pins on the front cylinder.


d.
E394762

Install the valve plate together with the discharge valve over the pins on the front cylinder.


e.
E394763

Lubricate the new gasket with compressor oil. Install the gasket on the valve plate.


f.
E394764

Install SST onto the shaft.

SST 95042-10810


g.

Install the mechanical seal to the shaft.


h.
E394765

Install a new O-ring to the seal plate.


i.

Using SST, install the seal plate to the front housing.

SST 95042-10540


j.
E394766

Using SST, install the lip seal to the front housing.

SST 95042-10611


k.
E394767

Using SST, install the snap ring.

SST 07714-84010


l.
E394768

Install SST onto the shaft.

SST 95042-10611


m.

Install the front housing with the 5 through bolts.

Torque:

37 N*m (375 kgf*cm, 27 ft.*lbf)



Hide 11.INSTALL KEY IN SHAFT GROOVE

Using SST, tap the key lightly by hand.

E394769

SST 95042-10530

Hide 12.INSTALL FELT

Using pipe, install a new felt to the front housing.

E394770

Hide 13. CHECK SHAFT STARTING TORQUE

Starting Torque:

12.7 N*m (130 kgf*cm, 9.4 in.*lbf) or less.


E394771

Hide 14. POUR COMPRESSOR OIL INTO COMPRESSOR

Add the same quantity plus 20 cc of oil into the compressor.

E394772

Compressor oil:

ND-OIL 8


Hide 15.INSTALL SERVICE VALVE

a.

Lubricate new O-ring with compressor oil. Install O-ring in the service valves.


b.

Install the service valves on the compressor.Using SST and torque wrench, tighten the bolts.

Torque:

25 N*m (260 kgf*cm, 19 ft.*lbf)


SST 07110-61050