Home › Vehicle Interior › LIGHTING › HEADLIGHT LEVELING SWITCH
RM2850E _58 Vehicle Interior _073208 LIGHTING _0356324 HEADLIGHT LEVELING SWITCH G

LIGHTING  HEADLIGHT LEVELING SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84152 1.INSPECT HEADLIGHT LEVELING SWITCH

a.

Remove the headlight leveling switch.

Click hereVehicle Interior>LIGHTING>HEADLIGHT LEVELING SWITCH>REMOVAL


b.
E362538E01
1.427,0.219 1.802,0.448 0.375,0.229 0.99,1.698 1.229,1.333 true 2.125,1.698 1.885,1.344 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.51,0.271 1.906,0.521 0.396,0.25 10 false J31 0.885,1.698 1.281,1.948 0.396,0.25 10 false B 2.177,1.677 2.573,1.927 0.396,0.25 10 false E

Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J31-4(E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
J31-1(B) - J31-4(E) Light control switch head 11 to 14 V


If the result is not as specified, repair or replace the wire harness or connector.


c.

Connect the connector.


d.

Turn the ignition switch to ON.


e.

Turn the light control switch head.


f.
E362549E01
1.531,0.198 1.885,0.406 0.354,0.208 0.927,1.021 1.344,1.021 true 1.833,1.01 1.833,0.542 1.833,0.542 2.396,0.542 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.604,0.24 1.969,0.5 0.365,0.26 10 false J31 0.802,0.958 1.167,1.219 0.365,0.26 10 false E 2.469,0.479 2.833,0.74 0.365,0.26 10 false RH 0

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J31-2(RH 0) - J31-4(E) 0 0.84 to 1.56 V
1 2.12 to 2.84 V
2 3.40 to 4.12 V
3 4.68 to 5.40 V
4 5.96 to 6.68 V
5 7.24 to 7.96 V


If the result is not as specified, replace the headlight leveling switch.

Text in Illustration
*a Component with harness connected
(Headlight Leveling Switch)


g.
E157014E03
1.156,1.5 1.51,1.5 true 1.938,0.938 1.688,0.938 1.688,0.938 1.688,1.438 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 1.01,1.417 1.323,1.625 0.313,0.208 10 false E 2,0.865 2.458,1.094 0.458,0.229 10 false ILL+

Apply battery voltage to the connector and check the light illumination condition.

OK:
Battery Connection Specified Condition
Positive → 3(ILL+)
Negative → 4(E)
Illuminates


If the result is not as specified, replace the headlight leveling switch.

Text in Illustration
*a Component with harness connected
(Headlight Leveling Switch)