Home › Vehicle Interior › LIGHTING › HEADLIGHT ASSEMBLY(for Dual Beam Headlight)
RM2850E _58 Vehicle Interior _073208 LIGHTING _0356331 HEADLIGHT ASSEMBLY(for Dual Beam Headlight) N

LIGHTING  HEADLIGHT ASSEMBLY(for Dual Beam Headlight)  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

for Headlight:

It is possible that the headlight assembly, No. 1 headlight bulb and No. 2 headlight bulb is incorrectly installed, affecting headlight aim. Headlight assembly, No. 1 headlight bulb and No. 2 headlight bulb installation should be considered prior to performing the adjustment procedure.

·

for Fog light:

It is possible that the headlight assembly and fog light bulb is incorrectly installed, affecting fog light aim. Headlight assembly and fog light bulb installation should be considered prior to performing the adjustment procedure.



PROCEDURE

Hide 1. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT

a.

Prepare the vehicle:

HINT:
·

Make sure that there is no damage to the body around the headlights.

·

Inflate the tires to the appropriate pressure.

·

Have a person of average weight (75 kg, 165 lb) sit in the driver seat.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Unload the vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Vehicles with manually adjustable headlights should be adjusted to "0".




Hide 2. PREPARE FOR HEADLIGHT AIMING (Using a screen)

a.
E363241E01
0.635,1.313 0.948,1.51 0.313,0.198 10 false *a 1.115,1.875 1.427,2.073 0.313,0.198 10 false *b

Prepare the vehicle.

Text in Illustration
*a 90°
*b 25 m or 3 m

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·
E361963E01
2.25,1.49 2.771,1.49 true 2.792,2.156 1.635,1.573 true 2.875,1.406 3.26,1.688 0.385,0.281 10 false *a 2.854,2.104 3.26,2.365 0.406,0.26 10 false *b

Create a 25 m (82 ft.) distance between the vehicle (center marks of the low beam) and the wall.

Text in Illustration
*a Low Beam Center Mark
*b High Beam Center Mark

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82 ft.) between the vehicle (center marks of the low beam) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).




b.

Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.

E363243E01
0.896,1.094 0.896,0.688 0.896,0.688 1.135,0.688 false 0.896,1.844 0.896,2.302 0.896,2.302 1.115,2.302 false 4.177,1.854 4.177,2.313 4.177,2.313 4.396,2.313 false 4.177,1.094 4.177,0.688 4.177,0.688 4.417,0.688 false 1.031,0.135 3.177,0.427 2.146,0.292 10 false Alignment distance is 25 m: 4.458,0.146 6.604,0.438 2.146,0.292 10 false Alignment distance is 3 m: 1.208,0.615 2.208,0.875 1,0.26 10 false V RH Line 1.177,1.188 1.594,1.438 0.417,0.25 10 false 90° 4.458,1.177 4.875,1.427 0.417,0.25 10 false 90° 4.469,3.708 4.885,3.958 0.417,0.25 10 false 90° 1.188,3.708 1.604,3.958 0.417,0.25 10 false 90° 1.198,2.219 2.198,2.479 1,0.26 10 false V LH Line 3.323,1.5 3.781,1.76 0.458,0.26 10 false V Line 6.625,1.5 7.083,1.76 0.458,0.26 10 false V Line 4.448,2.229 5.448,2.49 1,0.26 10 false V LH Line 4.458,0.604 5.458,0.865 1,0.26 10 false V RH Line 0.26,3.542 0.719,3.802 0.458,0.26 10 false H Line 3.552,3.563 4.01,3.823 0.458,0.26 10 false H Line 1.427,4.198 1.844,4.448 0.417,0.25 10 false 25 m 4.74,4.198 5.156,4.448 0.417,0.25 10 false 3 m




e.
E257183E04
1.17,0.275 1.331,0.419 0.161,0.143 10 *a 1.823,0.275 1.984,0.419 0.161,0.143 10 *b 2.446,0.275 2.607,0.419 0.161,0.143 10 *c 2.936,0.851 3.097,0.994 0.161,0.143 10 *d 0.547,1.698 0.708,1.841 0.161,0.143 10 *e

Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

Text in Illustration
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground

HINT:
·

The base lines differ for "low beam inspection" and "high beam inspection".

·

Mark the headlight center marks on the screen.



i.

H Line (Headlight height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight low beam center marks of the low beam headlights.


ii.

V LH Line, V RH Line (Center mark position of the left-hand (LH) and right-hand (RH) headlights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center marks of the low beam).



Hide 3.INSPECT HEADLIGHT AIMING

a.

Cover the headlight to prevent light from the headlight that is not being inspected from affecting the headlight aiming.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.


HINT:

When checking the aim of the high beam headlight, cover the low beam headlight.



b.

Start the engine.


c.

Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

HINT:
·

The low beam and high beam headlight are a unit, Adjusting the aim on the low beam to the correct position should also result in the high beam adjustment being correct.

·

The illustration for LHD vehicles. RHD vehicles are the opposite of the illustration.

·

If the alignment distance is 25 m (82 ft.):

The low beam cutoff line should be within 83 mm (3.27 in.) and 375 mm (14.8 in.) below the H line as well as 249 mm (9.80 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be within 10 mm (0.394 in.) and 45 mm (1.77 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 25 m (82 ft.):

The horizontal line of the preferred low beam cutoff line is 249 mm (9.80 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

E231280E24
3.99,1.875 4.604,1.427 false 0.5,1.875 1.083,1.448 false 1.771,1.438 2.094,0.635 2.094,0.635 2.271,0.635 true 5.229,1.417 5.552,0.615 5.552,0.615 5.729,0.615 true 0.875,0.156 3.104,0.427 2.229,0.271 12 false Aligning distance is 25 m: 4.302,0.177 6.438,0.427 2.135,0.25 12 false Aligning distance is 3 m: 5.781,0.552 6.406,0.792 0.625,0.24 10 false Point A 2.323,0.573 2.948,0.813 0.625,0.24 10 false Point A 1.156,0.917 1.635,1.083 0.479,0.167 10 false 83mm 4.615,0.906 5.094,1.073 0.479,0.167 10 false 10mm 4.708,1.813 5.125,2.01 0.417,0.198 10 false 30mm 5.344,1.823 5.76,2.021 0.417,0.198 10 false 30mm 6.365,1.281 6.781,1.479 0.417,0.198 10 false 45mm 1.875,1.792 2.375,2.021 0.5,0.229 10 false 249mm 3.708,1.5 4.125,1.698 0.417,0.198 10 false 30mm 2.885,1.323 3.448,1.5 0.563,0.177 10 false 375mm 1.219,1.792 1.719,2.021 0.5,0.229 10 false 249mm 0.177,1.521 0.677,1.75 0.5,0.229 10 false 249mm 0.188,1.094 0.688,1.323 0.5,0.229 10 false H Line 3.667,1.073 4.167,1.302 0.5,0.229 10 false H Line 1.073,2.365 2.604,2.573 1.531,0.208 10 false V LH Line or V RH Line 4.521,2.365 6.052,2.573 1.531,0.208 10 false V LH Line or V RH Line 0.01,1.917 1.042,2.229 1.031,0.313 10 false Preferred Cutoff Line 3.021,1.896 4.052,2.208 1.031,0.313 10 false Preferred Cutoff Line




d.

Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

HINT:
·

The low beam and high beam headlight are a unit, Adjusting the aim on the low beam to the correct position should also result in the high beam adjustment being correct.

·

The illustration for LHD vehicles. RHD vehicles are the opposite of the illustration.

·

If the alignment distance is 25 m (82 ft.):

The high beam center of intensity should be within 175 mm (6.88 in.) above and 249 mm (9.80 in.) below the H line as well as 497 mm (1.63 ft.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity should be within 21 mm (0.82 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.

E261529E07
1.646,1.365 2.125,0.583 2.125,0.583 2.344,0.583 true 5.052,1.354 5.531,0.573 5.531,0.573 5.75,0.573 true 0.75,0.167 3,0.469 2.25,0.302 12 false Alignment distance is 25 m: 4.229,0.167 6.333,0.458 2.104,0.292 12 false Alignment distance is 3 m: 2.438,0.5 3.583,0.698 1.146,0.198 10 false Center of Intensity 5.833,0.5 6.979,0.698 1.146,0.198 10 false Center of Intensity 0.198,1.292 1.115,1.49 0.917,0.198 10 false H Line 3.594,1.292 4.51,1.49 0.917,0.198 10 false H Line 2.719,0.917 3.49,1.115 0.771,0.198 10 false 175 mm 2.719,1.896 3.49,2.094 0.771,0.198 10 false 249 mm 1.063,2.052 1.833,2.25 0.771,0.198 10 false 497 mm 1.729,2.052 2.5,2.25 0.771,0.198 10 false 497 mm 4.479,2 5.25,2.198 0.771,0.198 10 false 60 mm 5.229,2 6,2.198 0.771,0.198 10 false 60 mm 6.146,1.854 6.917,2.052 0.771,0.198 10 false 30 mm 6.146,0.844 6.917,1.042 0.771,0.198 10 false 21 mm 1.01,2.417 3.917,2.615 2.906,0.198 10 false V LH Line or V RH Line 4.417,2.417 6.5,2.615 2.083,0.198 10 false V LH Line or V RH Line




Hide 4.ADJUSTMENT HEADLIGHT AIMING

a.
E360877

Using a screwdriver, adjust the aim.

Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

Text in Illustration
V100135

Vertical and Horizontal Aiming Screw
V100136

Vertical Aiming Screw

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

The low beam and high beam headlight are a unit, Adjusting the aim on the low beam to the correct position should also result in the high beam adjustment being correct.

·

When adjusting the vertical and horizontal axis of the headlight, the vertical axis will also change. It is necessary to adjust the vertical and horizontal position first, and then correct the vertical position.

·

If it is not possible to correctly adjust headlight aim, check the headlight assembly, No. 1 headlight bulb and No. 2 headlight bulb installation.

·

for LH Side:

The headlight aim moves up and right when turning the vertical and horizontal aiming screw clockwise, and moves down and left when turning the vertical and horizontal aiming screw counterclockwise. The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise.

·

for RH Side:

The headlight aim moves up and left when turning the vertical and horizontal aiming screw clockwise, and moves down and right when turning the vertical and horizontal aiming screw counterclockwise. The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted.Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.




Hide 5. PREPARE VEHICLE FOR FOG LIGHT AIMING

a.

Prepare the vehicle:

HINT:
·

Make sure that there is no damage to the body around the fog lights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Have a person of average weight (75 kg, 165 lb) sit in the driver seat.




Hide 6. PREPARE FOR FOG LIGHT AIMING (Using a screen) (w/ Fog Light)

a.
E363242E01
0.688,1.313 1,1.51 0.313,0.198 10 false *a 1.052,1.896 1.365,2.094 0.313,0.198 10 false *b

Prepare the vehicle.

Text in Illustration
*a 90°
*b 25 m or 3 m

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·
E363169E01
2.219,2.01 2.781,2.01 true 2.875,1.917 3.219,2.188 0.344,0.271 10 false *a

Create a 25 m (82 ft.) distance between the vehicle (fog light bulb center) and the wall.

Text in Illustration
*a Fog Light Bulb Center

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82 ft.) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).




b.

Set the screen as shown in the illustration.

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.

E363244E01
0.896,1.083 0.896,0.729 0.896,0.729 1.094,0.729 true 1.146,2.177 0.896,2.177 0.896,2.177 0.896,1.854 true 4.177,1.083 4.177,0.729 4.177,0.729 4.375,0.729 true 4.417,2.177 4.167,2.177 4.167,2.177 4.167,1.854 true 1.063,0.146 3.302,0.427 2.24,0.281 10 false Alignment distance is 25 m: 4.219,0.156 6.458,0.438 2.24,0.281 10 false Alignment distance is 3 m: 1.198,0.646 2.406,0.906 1.208,0.26 10 false V RH Line 4.479,0.656 5.667,0.917 1.188,0.26 10 false V RH Line 4.531,2.094 5.719,2.354 1.188,0.26 10 false V LH Line 1.25,2.115 2.438,2.375 1.188,0.26 10 false V LH Line 3.375,1.5 4.177,1.74 0.802,0.24 10 false V Line 6.646,1.51 7.156,1.781 0.51,0.271 10 false V Line 1.177,1.156 1.979,1.396 0.802,0.24 10 false 90° 4.479,1.177 5.281,1.417 0.802,0.24 10 false 90° 0.198,3.604 1.063,3.823 0.865,0.219 10 false H Line 3.49,3.604 4.354,3.823 0.865,0.219 10 false H Line 1.208,3.729 2.01,3.969 0.802,0.24 10 false 90° 4.458,3.719 5.26,3.958 0.802,0.24 10 false 90° 1.417,4.208 2.219,4.448 0.802,0.24 10 false 25 m 4.75,4.229 5.552,4.469 0.802,0.24 10 false 3 m




c.
E257183E04
1.17,0.275 1.331,0.419 0.161,0.143 10 *a 1.823,0.275 1.984,0.419 0.161,0.143 10 *b 2.446,0.275 2.607,0.419 0.161,0.143 10 *c 2.936,0.851 3.097,0.994 0.161,0.143 10 *d 0.547,1.698 0.708,1.841 0.161,0.143 10 *e

Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

Text in Illustration
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground

HINT:

Mark the center of the fog light bulb on the screen.


i.

H line (Fog light height):

Draw a horizontal line across the screen so that it passes through the both sides of the fog light bulb center. The H line should be at the same height as the both sides of the fog light bulb center.


ii.

V LH Line, V RH Line (Bulb center position of left-hand (LH) and right-hand (RH) fog lights):

Draw 2 vertical lines so that they intersect the H line at each fog light bulb center.



Hide 7.INSPECT FOG LIGHT AIMING (w/ Fog Light)

a.

Cover the headlight or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.



b.

Start the engine.


c.

Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration.

HINT:
·

If the alignment distance is 25 m (82 ft.):

The upper edge of the hot zone for the fog light should be 376 mm (1.24 ft.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The upper edge of the hot zone for the fog light should be 46 mm (1.78 in.) below the H line.



E168642E69
1.958,1.896 2.104,2.417 2.104,2.417 2.333,2.417 false 5.333,1.896 5.49,2.417 5.49,2.417 5.719,2.417 false 2.792,1.917 3.333,2.104 0.542,0.188 10 376 mm 6.198,1.917 6.667,2.104 0.469,0.188 10 46 mm 0.781,0.083 2.896,0.323 2.115,0.24 12 Alignment distance is 25 m: 4.208,0.083 6.198,0.313 1.99,0.229 12 Alignment distance is 3 m: 0.302,1.417 0.75,1.75 0.448,0.333 10 H Line 3.667,1.427 4.115,1.75 0.448,0.323 10 H Line 1.531,0.917 2.167,1.25 0.635,0.333 10 V LH Line 4.844,1.167 5.5,1.5 0.656,0.333 10 V RH Line 4.833,0.917 5.469,1.229 0.635,0.313 10 V LH Line 1.521,1.167 2.177,1.5 0.656,0.333 10 V RH Line 2.375,2.333 2.969,2.635 0.594,0.302 10 Hot Zone 5.75,2.333 6.344,2.635 0.594,0.302 10 Hot Zone


Hide 8.ADJUST FOG LIGHT AIMING (w/ Fog Light)

a.
E360878E01
0.885,2.417 1.24,2.281 true 1.24,2.156 1.552,2.354 0.313,0.198 10 false *a

Adjust the aim vertically:

Adjust the aim of each fog light so that it is within the specified range by turning the aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


Text in Illustration
*a Aiming screw

HINT:

If it is not possible to correctly adjust fog light aim, check the headlight assembly and fog light bulb installation.