Home › Vehicle Interior › WIPER / WASHER › WIPER SWITCH
RM2850E _58 Vehicle Interior _073209 WIPER / WASHER _0356345 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)

a.

Remove the steering column cover (Click hereVehicle Interior>WIPER / WASHER>WIPER SWITCH>REMOVAL).


b.
E229602E04
1.448,0.229 1.885,0.458 0.438,0.229 0.823,0.51 1.729,1.073 true 1.917,1.073 2.542,0.51 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.552,0.25 1.865,0.448 0.313,0.198 10 false J65 0.531,0.417 0.844,0.615 0.313,0.198 10 false EW 2.604,0.427 2.917,0.625 0.313,0.198 10 false WF

Check operation (front washer):

i.

Connect a voltmeter positive (+) lead to terminal J65-4 (WF) and a negative (-) lead to terminal J65-5 (EW).


ii.

Turn the ignition switch to ON.

Text in Illustration
*a Component with harness connected
(Windshield wiper switch assembly)


iii.

Turn the front washer switch on and off positions, and measure the voltage between terminals J65-4 (WF) and J65-5 (EW).

OK:

Voltage changes as shown in the following illustration.


E136494E35
2.417,0.083 2.729,0.281 0.313,0.198 10 false *1 2.417,0.833 2.729,1.031 0.313,0.198 10 false *a 3.292,0.25 3.604,0.448 0.313,0.198 10 false ON 3.24,0.49 3.552,0.688 0.313,0.198 10 false OFF 2.865,0.844 3.615,1.042 0.75,0.198 10 false 11 to 14 V 3.271,1.083 3.635,1.271 0.365,0.188 10 false 0 V 4.042,1.323 4.406,1.51 0.365,0.188 10 false *b 4.688,1.313 5.052,1.5 0.365,0.188 10 false *c

Text in Illustration
*1 Washer Switch - -
*a Voltage between terminals J65-4 (WF) - J65-5 (EW) *b Approximately 0.3 seconds
*c Approximately 2.5 seconds - -

If the result is not as specified, replace the windshield wiper switch assembly.



c.
E229602E05
1.49,0.323 1.948,0.542 0.458,0.219 1.156,1.635 1.417,1.26 true 2.146,1.656 1.781,1.271 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.615,0.344 1.927,0.542 0.313,0.198 10 false J65 0.99,1.688 1.302,1.885 0.313,0.198 10 false EW 2.063,1.688 2.375,1.885 0.313,0.198 10 false WR

Check operation (rear washer):

i.

Connect a voltmeter positive (+) lead to terminal J65-15 (WR) and a negative (-) lead to terminal J65-18 (EW).


ii.

Turn the ignition switch to ON.

Text in Illustration
*a Component with harness connected
(Windshield wiper switch assembly)


iii.

Turn the rear washer switch on and off positions, and measure the voltage between terminals J65-15 (WR) and J65-18 (EW).

OK:

Voltage changes as shown in the following illustration.


E136494E35
2.417,0.083 2.729,0.281 0.313,0.198 10 false *1 2.417,0.833 2.729,1.031 0.313,0.198 10 false *a 3.292,0.25 3.604,0.448 0.313,0.198 10 false ON 3.24,0.49 3.552,0.688 0.313,0.198 10 false OFF 2.865,0.844 3.615,1.042 0.75,0.198 10 false 11 to 14 V 3.271,1.083 3.635,1.271 0.365,0.188 10 false 0 V 4.042,1.323 4.406,1.51 0.365,0.188 10 false *b 4.688,1.313 5.052,1.5 0.365,0.188 10 false *c

Text in Illustration
*1 Rear Washer Switch - -
*a Voltage between terminals J65-15 (WR) - J65-18 (EW) *b Approximately 0.5 seconds
*c Approximately 2.5 seconds - -

If the result is not as specified, replace the windshield wiper switch assembly.



d.

Install the steering column cover (Click hereVehicle Interior>WIPER / WASHER>WIPER SWITCH>INSTALLATION).


Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)

a.

Remove the steering column cover (Click hereVehicle Interior>WIPER / WASHER>WIPER SWITCH>REMOVAL).


b.
E229602E06
1.49,0.219 1.896,0.417 0.406,0.198 1.5,1.083 0.958,0.542 true 1.688,1.073 2.313,0.49 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.708,0.438 1.021,0.635 0.313,0.198 10 false WF 2.375,0.396 2.688,0.594 0.313,0.198 10 false EW 1.583,0.229 1.896,0.427 0.313,0.198 10 false J65

Check operation (front washer):

i.

Connect a voltmeter positive (+) lead to terminal J65-7 (WF) and a negative (-) lead to terminal J65-6 (EW).


ii.

Turn the ignition switch to ON.

Text in Illustration
*a Component with harness connected
(Windshield wiper switch assembly)


iii.

Turn the front washer switch on and off positions, and measure the voltage between terminals J65-7 (WF) and J65-6 (EW).

OK:

Voltage changes as shown in the following illustration.


E136494E35
2.417,0.083 2.729,0.281 0.313,0.198 10 false *1 2.417,0.833 2.729,1.031 0.313,0.198 10 false *a 3.292,0.25 3.604,0.448 0.313,0.198 10 false ON 3.24,0.49 3.552,0.688 0.313,0.198 10 false OFF 2.865,0.844 3.615,1.042 0.75,0.198 10 false 11 to 14 V 3.271,1.083 3.635,1.271 0.365,0.188 10 false 0 V 4.042,1.323 4.406,1.51 0.365,0.188 10 false *b 4.688,1.313 5.052,1.5 0.365,0.188 10 false *c

Text in Illustration
*1 Washer Switch - -
*a Voltage between terminals J65-7 (WF) - J65-6 (EW) *b Approximately 0.3 seconds
*c Approximately 2.5 seconds - -

If the result is not as specified, replace the windshield wiper switch assembly.



c.
E229602E07
1.5,0.281 1.927,0.521 0.427,0.24 1.354,1.583 1.625,1.26 true 2.229,1.604 1.979,1.26 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.604,0.313 1.917,0.51 0.313,0.198 10 false J65 1.198,1.615 1.51,1.813 0.313,0.198 10 false WR 2.115,1.625 2.427,1.823 0.313,0.198 10 false EW

Check operation (rear washer):

i.

Connect a voltmeter positive (+) lead to terminal J65-16 (WR) and a negative (-) lead to terminal J65-13 (EW).


ii.

Turn the ignition switch to ON.

Text in Illustration
*a Component with harness connected
(Windshield wiper switch assembly)


iii.

Turn the rear washer switch on and off positions, and measure the voltage between terminals J65-16 (WR) and J65-13 (EW).

OK:

Voltage changes as shown in the following illustration.


E136494E35
2.417,0.083 2.729,0.281 0.313,0.198 10 false *1 2.417,0.833 2.729,1.031 0.313,0.198 10 false *a 3.292,0.25 3.604,0.448 0.313,0.198 10 false ON 3.24,0.49 3.552,0.688 0.313,0.198 10 false OFF 2.865,0.844 3.615,1.042 0.75,0.198 10 false 11 to 14 V 3.271,1.083 3.635,1.271 0.365,0.188 10 false 0 V 4.042,1.323 4.406,1.51 0.365,0.188 10 false *b 4.688,1.313 5.052,1.5 0.365,0.188 10 false *c

Text in Illustration
*1 Rear Washer Switch - -
*a Voltage between terminals J65-16 (WR) - J65-13 (EW) *b Approximately 0.5 seconds
*c Approximately 2.5 seconds - -

If the result is not as specified, replace the windshield wiper switch assembly.



d.

Install the steering column cover (Click hereVehicle Interior>WIPER / WASHER>WIPER SWITCH>INSTALLATION).