Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
67001
1.INSPECT FRONT DOOR PANEL SUB-ASSEMBLY RH
Check that the clearance measurements of areas A to E are within the standard ranges.
| Area | Measurement Condition | Specified Condition |
|---|---|---|
| A | 2 Coat Application | 4.3 to 7.3 mm (0.169 to 0.287 in.) |
| 4 Coat Application | 4.2 to 7.2 mm (0.165 to 0.283 in.) | |
| 2 Coat Application + Black Out Tape | 4.0 to 7.0 mm (0.157 to 0.276 in.) | |
| 4 Coat Application + Black Out Tape | 3.9 to 6.9 mm (0.154 to 0.272 in.) | |
| B | 2 Coat Application | 3.2 to 6.2mm (0.126 to 0.244 in.) |
| 4 Coat Application | 3.1 to 6.1mm (0.122 to 0.240 in.) | |
| 2 Coat Application + Black Out Tape | 2.9 to 5.9mm (0.114 to 0.232 in.) | |
| 4 Coat Application + Black Out Tape | 2.8 to 5.8mm (0.110 to 0.228 in.) | |
| C | 2 Coat Application | 4.4 to 7.4 mm (0.173 to 0.291 in.) |
| 4 Coat Application | 4.3 to 7.3 mm (0.169 to 0.287 in.) | |
| 2 Coat Application + Black Out Tape | 4.1 to 7.1 mm (0.161 to 0.280 in.) | |
| 4 Coat Application + Black Out Tape | 4.0 to 7.0 mm (0.157 to 0.276 in.) | |
| D | 2 Coat Application | 3.7 to 8.7 mm (0.146 to 0.343 in.) |
| 4 Coat Application | 3.6 to 8.6 mm (0.142 to 0.339 in.) | |
| 2 Coat Application + Black Out Tape | 3.4 to 8.4 mm (0.134 to 0.331 in.) | |
| 4 Coat Application + Black Out Tape | 3.3 to 8.3 mm (0.130 to 0.327 in.) | |
| E | 2 Coat Application | -0.9 to 4.1 mm (0.035 to 0.161 in.) |
| 4 Coat Application | -1.0 to 4.0 mm (0.039 to 0.157 in.) | |
| 2 Coat Application + Black Out Tape | -1.2 to 3.8 mm (0.047 to 0.149 in.) | |
| 4 Coat Application + Black Out Tape | -1.3 to 3.7 mm (0.051 to 0.146 in.) |
67001
2.ADJUST FRONT DOOR PANEL SUB-ASSEMBLY RH
Using SST, loosen the body side bolt and adjust the horizontal and vertical axis of the door.
Tighten the body side bolt on the body after the adjustment.
24 N*m (245 kgf*cm, 18 ft.*lbf)
Loosen the door side bolt and adjust the vertical axis of the door and the horizontal axis for the front of the door.
Tighten the door side bolts on the body after the adjustment.
32.5 N*m (331 kgf*cm, 288 ft.*lbf)
A center ring bolt is used in the factory assembly stage. Therefore, it is necessary to replace it with a replacement bolt when performing adjustments.
Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a brass bar and hammer.
Tighten the striker mounting screws on the body after the adjustment.
12 N*m (122 kgf*cm, 9 ft.*lbf)