Home › Vehicle Interior › EXTERIOR › NAME PLATE
RM2850E _58 Vehicle Interior _073214 EXTERIOR _0356378 NAME PLATE A

EXTERIOR  NAME PLATE  INSTALLATION  


PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the back door or luggage compartment door surface.

i.

using a heat light, heat the back door or luggage compartment door surface.

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




ii.

wipe off any tape adhesive with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the back door or luggage compartment door surface (installation surface of the back door or luggage compartment door) and tape to between 20 and 30°C (68 and 86°F) using a heat light.

When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the back door or luggage compartment door surface where the tape will be installed (installation surface of the back door or luggage compartment door) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the name plate.

i.

The name plate bends and rolls up easily. Store the name plate between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in a place with a high temperature.




e.

Key points for the installation of the name plate (how to use a squeegee and the installation procedure for a flat surface).

NOTICE:
·

Position the name plate with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The name plate cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the name plate that is going to be applied so that its adhesive surface does not touch the back door or luggage compartment door while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the back door or luggage compartment door surface and press with a force of 20 to 30 N (2 to 3 kgf. 1.45 to 6.71 lbf.) while moving the squeegee at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.

B233855E19
0.083,0.073 3.875,1.563 3.792,1.49 0.688,0.625 0.833,0.479 0.833,0.479 1,0.479 false 2.177,0.74 2.292,0.365 2.292,0.365 2.542,0.365 false 2.135,1.25 2.833,1.25 false 2.146,1.99 2.146,1.823 2.146,1.823 2.604,1.823 true 2.094,3.427 2.646,3.427 true 4.594,2.635 4.99,2.635 false 4.875,3.052 5.302,3.052 false 5.698,2.635 5.938,2.979 5.938,2.979 6.052,2.979 true 5.677,3.271 6.073,3.271 false 1.021,2.865 1.781,2.865 1.781,2.865 2.021,2.281 false 1.125,3.26 1.646,3.26 false 4.552,2.24 5,2.5 0.448,0.26 10 false *e 2.698,1.729 3.292,1.969 0.594,0.24 10 false *d 6.125,2.885 6.583,3.198 0.458,0.313 10 false *g 2.885,2.385 3.281,2.698 0.396,0.313 10 false *f 0.167,0.104 0.427,0.385 0.26,0.281 10 false *a 2.594,0.281 2.875,0.542 0.281,0.26 10 false *b 2.885,1.167 3.198,1.448 0.313,0.281 10 false *c 1.021,0.396 1.323,0.667 0.302,0.271 10 false *1 0.813,2.792 1.146,3.052 0.333,0.26 10 false *1 0.094,1.635 0.5,1.906 0.406,0.271 10 false *A 0.938,3.177 1.229,3.406 0.292,0.229 10 false *2 4.406,2.542 4.708,2.802 0.302,0.26 10 false *1 4.667,2.979 5.063,3.25 0.396,0.271 10 false *2 2.688,3.344 2.958,3.573 0.271,0.229 10 false *3 3.677,1.635 4,1.885 0.323,0.25 10 false *B 6.115,3.198 6.51,3.469 0.396,0.271 10 false *3 1.083,2.25 1.531,2.51 0.448,0.26 10 false *e 6.354,2.042 6.75,2.354 0.396,0.313 10 false *f

Text in Illustration
*A Protective Tape *B Pulling
*1 Squeegee *2 Name Plate
*3 Release Paper - -
*a Sectional View *b Non-padded Side
*c Padded Side *d 40 to 50° (for pressing forward)
*e 30 to 70 mm/sec. (1.18 to 2.76 in/sec.) *f 10 to 20 mm (0.39 to 0.79 in.)
*g 30 to 45° (for pulling) - -

NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.39 to 0.79 in.) from the edge of the squeegee.





f.
B233856E04
0.969,1.792 1.083,1.792 1.083,1.792 1.198,1.698 false 0.74,1.698 0.938,1.854 0.198,0.156 10 false *1 2.333,0.438 2.51,0.615 0.177,0.177 10 false *a 1.625,0.333 1.823,0.51 0.198,0.177 10 false *b 0.906,0.427 1.115,0.625 0.208,0.198 10 false *c 1.771,1.833 2.104,2.031 0.333,0.198 10 false *2

Key points for the installation of the name plate (how to use a squeegee and the installation procedure for a hemming surface).

i.

If it is difficult to press the name plate, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the name plate to the hem of the vehicle, especially for a small hem.

Text in Illustration
*1 Squeegee
*2 Hem
*a First
*a Second
*b Third

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the name plate (how to use a squeegee and the installation procedure for corners).

i.

Remove the release paper and apply the name plate carefully with your fingers.


ii.

Before applying the name plate to each corner, heat the name plate using a heat light and gradually apply it to avoid wrinkles in the name plate and achieve a neat finish.



h.

Check after installation.

i.

After completing the application, check if the name plate is applied neatly. If the name plate is not applied neatly, apply new name plate.

NOTICE:

Do not reuse the name plate.




Hide 75311 2.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

a.

Align the guide, attach the 3 claws and install the radiator grille (or front panel) emblem.


Hide 52119A 3.INSTALL FRONT BUMPER COVER (w/o Snorkel Air Cleaner)

Hide 52119A 4.INSTALL FRONT BUMPER COVER (w/ Snorkel Air Cleaner)

Hide 75431A 5.INSTALL NO. 1 BACK DOOR EMBLEM (for Double Swing Out Type)

HINT:

When installing the No. 1 back door emblem, heat the back door and No. 1 back door emblem using a heat light.


Standard
Item Temperature
Back Door 40 to 60°C (104 to 140°F)
No.1 Back Door Emblem 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the back door or No. 1 back door emblem excessively.


a.

Clean the No. 1 back door emblem installation surface.

i.

Using a heat light, heat the back door surface.


ii.

Remove the double-sided tape from the back door.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 1 back door emblem.

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



i.

Using a heat light, heat the back door and a new No. 1 back door emblem.


ii.

Remove the peeling paper from the face of the No. 1 back door emblem.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B466080E01
1.313,1.708 1.563,1.708 1.563,1.708 1.563,1.854 false 0.198,1.542 0.198,1.365 0.198,1.365 0.333,1.365 false 0.125,1.552 0.365,1.719 0.24,0.167 10 false *a 1.5,1.875 1.74,2.042 0.24,0.167 10 false *a

Align the boss positions and install the No. 1 back door emblem.

HINT:

Press the No. 1 back door emblem firmly to install it.


Text in Illustration
*a Boss



Hide 75431A 6.INSTALL NO. 1 BACK DOOR EMBLEM (for Luggage Compartment)

HINT:

Use the same procedure described for the double swing out type.


Hide 75471B 7.INSTALL NO. 1 REAR BODY NAME PLATE (for Luggage Compartment)

HINT:

When installing the No. 1 rear body name plate, heat the luggage compartment door and No. 1 rear body name plate using a heat light.


Standard
Item Temperature
Luggage Compartment Door 40 to 60°C (104 to 140°F)
No. 1 Rear Body Name Plate 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the luggage compartment door or No. 1 rear body name plate excessively.


a.

Clean the luggage compartment door surface.

i.

Using a heat light, heat the luggage compartment door surface.


ii.

Remove the double-sided tape from the luggage compartment door.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 1 rear body name plate.

i.

Using a heat light, heat the luggage compartment door and a new No. 1 rear body name plate.


ii.

Remove the peeling paper from the face of the No. 1 rear body name plate.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B466081E01
2.333,1.469 2.406,1.292 2.406,1.292 2.615,1.292 true 1.865,0.469 2.01,0.302 2.01,0.302 2.219,0.302 true 1.313,0.344 1.625,0.542 0.313,0.198 10 false *a 0.406,0.854 0.604,1.042 0.198,0.188 10 false *b 2.26,0.229 2.458,0.417 0.198,0.188 10 false *c 2.646,1.229 2.844,1.417 0.198,0.188 10 false *d

Align the boss positions and install the No. 1 rear body name plate.

Text in Illustration
*a 257 mm (10.118 in.)
*b 69.3 mm (2.728 in.)
*c Vehicle Center
*d Edge of Curved Surface



Hide 75471B 8.INSTALL NO. 1 REAR BODY NAME PLATE (for Double Swing Out Type)

HINT:

When installing the No. 1 rear body name plate, heat the back door and No. 1 rear body name plate using a heat light.


Standard
Item Temperature
Back Door 40 to 60°C (104 to 140°F)
No. 1 Rear Body Name Plate 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the back door or No. 1 rear body name plate excessively.


a.

Clean the back door surface.

i.

Using a heat light, heat the back door surface.


ii.

Remove the double-sided tape from the back door.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 1 rear body name plate.

i.

Using a heat light, heat the back door and a new No. 1 rear body name plate.


ii.

Remove the peeling paper from the face of the No. 1 rear body name plate.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B466083E01
1.729,0.646 2.083,0.229 2.083,0.229 2.396,0.229 true 2.427,1.219 2.76,0.896 2.76,0.896 2.969,0.896 true 1.188,0.229 1.5,0.427 0.313,0.198 10 false *a 2.438,0.156 2.75,0.354 0.313,0.198 10 false *c 3.01,0.813 3.323,1.01 0.313,0.198 10 false *d 2.313,1.448 2.521,1.615 0.208,0.167 10 false *b

Align the boss positions and install the No. 1 rear body name plate.

HINT:

Press the No. 1 rear body name plate firmly to install it.


Text in Illustration
*a 257 mm (10.118 in.)
*b 13.7 mm (0.539 in.)
*c No. 1 Back Door Emblem Center
*d Edge of Curved Surface



Hide 75472A 9.INSTALL NO. 2 REAR BODY NAME PLATE (for Luggage Compartment)

HINT:

When installing the No. 2 rear body name plate, heat the luggage compartment door and No. 2 rear body name plate using a heat light.


Standard
Item Temperature
Luggage Compartment Door 40 to 60°C (104 to 140°F)
No. 2 Rear Body Name Plate 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the luggage compartment door or No. 2 rear body name plate excessively.


a.

Clean the luggage compartment door surface.

i.

Using a heat light, heat the luggage compartment door surface.


ii.

Remove the double-sided tape from the luggage compartment door.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 2 rear body name plate.

i.

Using a heat light, heat the luggage compartment and a new No. 2 rear body name plate.


ii.

Remove the peeling paper from the face of the No. 2 rear body name plate.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B466085E01
1.865,0.438 2.01,0.188 2.01,0.188 2.292,0.188 true 2.885,1.458 2.958,1.333 2.958,1.333 3.104,1.333 true 1.292,0.135 1.604,0.333 0.313,0.198 10 false *a 2.365,0.115 2.677,0.313 0.313,0.198 10 false *c 0.292,0.76 0.604,0.958 0.313,0.198 10 false *b 3.156,1.26 3.365,1.427 0.208,0.167 10 false *d

Align the boss positions and install the No. 2 rear body name plate.

HINT:

Press the No. 2 rear body name plate firmly to install it.


Text in Illustration
*a 257 mm (10.118 in.)
*b 12.3 mm (0.484 in.)
*c Vehicle Center
*d Edge of Curved Surface



Hide 75472A 10.INSTALL NO. 2 REAR BODY NAME PLATE (for Double Swing Out Type)

HINT:

When installing the No. 2 rear body name plate, heat the back door and No. 2 rear body name plate using a heat light.


Standard
Item Temperature
Back Door 40 to 60°C (104 to 140°F)
No. 2 Rear Body Name Plate 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the back door or No. 2 rear body name plate excessively.


a.

Clean the back door surface.

i.

Using a heat light, heat the back door surface.


ii.

Remove the double-sided tape from the back door.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 2 rear body name plate.

i.

Using a heat light, heat the back door and a new No. 2 rear body name plate.


ii.

Remove the peeling paper from the face of the No. 2 rear body name plate.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B466087E01
1.729,0.583 2.083,0.229 2.083,0.229 2.365,0.229 true 2.063,1.219 2.156,1.052 2.156,1.052 2.323,1.052 true 1.125,0.219 1.438,0.417 0.313,0.198 10 false *a 2.427,0.156 2.667,0.333 0.24,0.177 10 false *c 2.375,0.979 2.573,1.135 0.198,0.156 10 false *d 2.75,0.594 2.938,0.802 0.188,0.208 10 true *b

Align the boss positions and install the No. 2 rear body name plate.

HINT:

Press the No. 2 rear body name plate firmly to install it.


Text in Illustration
*a 257 mm (10.118 in.)
*b 13.7 mm (0.539 in.)
*c No. 2 Back Door Emblem Center
*d Edge of Curved Surface